• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1513-1520
• /
• 2000

Complex modal testing method for rotating disks with support motion is introduced which handles the pairs of two point excitation and responses of the disk as complex input and output, respectively. This method utilizes the directivity information and the separation over the rotational speed of forward and backward traveling wave modes or bending coupled modes in the directional frequency response functions(dFRFs). This method synthesizes the normal/reverse dFRFs and complex wave dFRF, which were originally applied to rotating shaft and rotating disk, respectively, and is applied to complex system with dynamically coupled rotating disks and shaft. Experiments with a commercial hard disk drive spindle system demonstrate the validity of this method.

• 한국안전학회지
• /
• 제10권4호
• /
• pp.9-12
• /
• 1995

Detection of small defects by medical ultrasonic testing when the thermal sprayed coating by $MoSi_2$ on the metal is done. The defects may occur at the bonded surface. So, the detecting method of the defects by non-destructive in spection is desired. Here, in order to examine the possibility of the detection of the small defects by the ultrasonic. The electronic scanning ultrasonic equipment using an array probe developed as the medical ultrasonic diagnostic equipment is applied for the detection of the metal material defects. It's validity is investigated.

• 한국통신학회논문지
• /
• 제21권8호
• /
• pp.1948-1957
• /
• 1996

통신 프로토콜의 적합성 시험은 구현된 프로토콜이 표준규격과 동일하게 구현되었는지를 검사하는 과정을 말한다. 생성된 시험 항목이 어느 정도의 오류를 발견해 낼 수 있는지를 평가함으로써 적합성 시험의 효율성을 평가하는 하나의 기준으로 사용될 수 있다. 시험 항목의 오류 발견 능력의 평가 방법은 주로 수학적 평가 방법과 시뮬레이션을 이용한 연구가 이루어져 왔다. 본 논문에서는 기존 평가 방법의 문제점을 지적하고 오류 모델을 사용하여 생성된 시험항목에 대한 새로운 오류 발견 평가 모델을 제시하였다. 그리고 제안된 평가 모델을 기존의 방법과 비교, 분석하여 타당성을 입증하였다.

• 한국품질경영학회:학술대회논문집
• /
• 한국품질경영학회 2004년도 품질경영모델을 통한 가치 창출
• /
• pp.655-673
• /
• 2004

This paper is concerned with analysing the bankruptcy prediction power of three models: Multivariate Discriminant Analysis(MDA ), Logit Analysis, Neural Network. The after-crisis bankrupted companies were limited to the research data and the listed companies belonging to manufacturing industry was limited to the research data so as to improve prediction accuracy and validity of the model. In order to assure meaningful bankruptcy prediction, training data and testing data were not extracted within the corresponding period. The result is that prediction accuracy of neural network model is more excellent than that of logit analysis and MDA model when considering that execution of testing data was followed by execution of training data.

• Journal of Welding and Joining
• /
• 제11권1호
• /
• pp.42-51
• /
• 1993

In this study, investigations were conducted in calculating parameters of elastic-plastic fracture mechanics using single specimen. The validity of these testing methods was judged by the confirmation of multiple specimen method of stop block test. The results were as follows: In order to measure a fracture toughness using the instrumented impact test, two general requirement must be considered; One, setting up proper impact velocity considered the effect of loading and the other, the necessity of low blow test for obtaining true energy by the compliance correction. It was possible to detect a crack initiation point by calculating the compliance changing rate from a load-defection curve. Criterion of a stable crack growth, $T_{mat}$ could be estimated by using key-curve method for a base metal. and combining Kaiser's rebound compliance with Paris-Hutchison's $T_{appl}$ equation for the brittled zone of welding heat affected.at affected.d.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.35.2-35.2
• /
• 2011

A wind turbine power performance test is very important to wind turbine manufacturers because a wind farm developer or planner must want to define power performance characteristics and reliability of new wind turbines. Based on the IEC 61400-12-1, A wind turbine test site has to be nicely installed at flat terrain for testing. We are developing the wind power system which is IEC wind class IIa model with rated power of 3MW. KEPCO's Gochang power testing center was considered as candidates to build the test site without site calibration. This paper aims to verify the validity of the test site by using implement site assessment result that was based on IEC 61400-12-1.

• 대한전자공학회논문지
• /
• 제24권3호
• /
• pp.517-526
• /
• 1987

This paper proposes a new testable design for Zipper CMOS circuits. This design provides an additional feedback loop (called self oscillation loop) whichin the circuit, for testability. The circuit is tested only by observing the oscillation on the loop. The design can be applied to the multistage as well as the single stage, and can detect multiple faults which are undetectable by the conventional testing method. The application and evaluation of test patterns become easy and fault-free responses are not necessary. If the conventional testing method is applied to the sequential Zipper CMOS circuit with the LSSD design technique, it has the serious defect that the initial value may change due to intermediate test patterns and much time taken to apply the necessary test patterns. By using the proposed design, however, the sequential Zipper CMOS circuit with the LSSD design technique can be easily tested without such a defect. Also, the validity of the design is verified by performing the circuit level simulation.

• 산업기술연구
• /
• 제27권A호
• /
• pp.47-53
• /
• 2007

A theoretical model based on Rayleigh-Ritz method is proposed to predict the resonance frequency of a W/T(Wind Turbine) tower structure supported by guy cables. In order to verify the validity of the theoretical model, a reduced W/T tower system is manufactured and tested. Frequency response and mode data are determined by modal testing and finite element analysis is performed to calculate the natural frequency of the tower model. Numerical and experimental results are compared with those by the theoretical analysis. Parametric study by the theoretical model shows how the cable tension and cable elasticity influence the resonance frequency of the W/T tower structure. Finally, vibration response under various rotating speed is investigated to examine the possibility of severe resonance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 A
• /
• pp.220-222
• /
• 1999

This paper presents a numerical analysis of the eddy current testing with cracked pipe using finite element method (FEM). ${\vec{A}},\;{\phi}-{\vec{A}}$ method is adopted for the formulation of 3-dimensional(3-D) FEM with the brick element. The cracks investigated here are the inner and outer surface of axial symmetry, 90 degree circular one. The algorithm of 3-D numerical analysis is employed for the axisymmetric pipe with the cracks. In order to verify the validity of 3-D numerical analysis, the results are compared with those of 2-D analysis with the same type of the model. The differential impedance is obtained by using energy method and its locus are various 8-shaped curves for each cracks. The ICCG method is used for the calculation of a matrix.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.623-629
• /
• 2002

The spectrum of impulse response signal from an impulse hammer testing is widely used to obtain frequency response function(FRF) of the structure. However the FRFs obtained from impact hammer testing have not only leakage errors but also finite record length errors when the record length for the signal processing is not sufficiently long. The errors cannot be removed with the conventional signal analyzer which treats the signals as if they are always steady and periodic. Since the response signals generated by the impact hammer are transient and have damping, they are undoubtedly non-periodic. It is inevitable that the signals be acquired for limited recording time, which causes the finite record length error and the leakage error. In this paper, the errors in the frequency response function of multi degree of freedom system are formulated theoretically. And the method to remove these errors is also suggested. This method is based on the optimization technique. A numerical example of 3-dof model shows the validity of the proposed method.