• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.09a
• /
• pp.125-153
• /
• 2005

It has been widely known that the seismic piezo-cone penetration test (SCPTU) is one of the most useful techniques for investigating the geotechnical characteristics including dynamic soil properties. As the practical applications in Korea, SCPTU was carried out at two sites in Busan and four sites in Incheon, which are mainly composed of alluvial or marine soil deposits. From the SCPTU waveform data obtained from the testing sites, the first arrival times of shear waves were and the corresponding time differences with depth were determined using the cross-over method, and the shear wave velocity profiles (VS) were derived based on the refracted ray path method based on Snell's law and similar to the trend of cone tip resistance (qt) profiles. In Incheon area, the testing depths of SCPTU were deeper than those of conventional down-hole seismic tests. Moreover, for the application of the conventional CPTU to earthquake engineering practices, the correlations between VS and CPTU data were deduced based on the SCPTU results. For the empirical evaluation of VS for all soils together with clays and sands which are classified unambiguously in this study by the soil behavior type classification Index (IC), the authors suggested the VS-CPTU data correlations expressed as a function of four parameters, qt, fs, $\sigma$, v0 and Bq, determined by multiple statistical regression modeling. Despite the incompatible strain levels of the down-hole seismic test during SCPTU and the conventional CPTU, it is shown that the VS-CPTU data correlations for all soils clays and sands suggested in this study is applicable to the preliminary estimation of VS for the Korean deposits and is more reliable than the previous correlations proposed by other researchers.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.6 no.3
• /
• pp.189-203
• /
• 2008

The physical and chemical properties of radioactive waste drums, which have been temporarily stored on site, should be characterized before their shipment to a disposal facility in order to prove that the properties meet the acceptance guideline. The investigation of NDT(Nondestructive Test) method was figured out that the contents in drum, the quantitative analysis of free standing water and void fraction can be examined with X-ray NDT techniques. This paper describes the characteristics of X-ray NDT such as its principles, the considerations for selection of X-ray system, etc. And then, the waste drum characteristics such as drum type and dimension, contents in drum, etc. were examined, which are necessary to estimate the optimal X-ray energy for NDT of a drum. The estimation results were that: $(R)\acute{A}$ the proper X-ray energy is under 3 MeV to test the drums of 320 ${\beta}\S$ and less; $(R)\ddot{E}$ both X-ray systems of 450 keV and/or 3 MeV might be needed considering the economical efficiency and the realization. The number of drums that can be tested with 450 keV and 3 MeV X-ray system was figured out as 42,327 and 18,105 drums (based on storage of 2006. 12), respectively. Four testing scenarios were derived considering equipment procurement method, outsourcing or not, etc. The economical and feasibility assessment for the scenarios was resulted in that an optimal scenario is dependent on the acceptance guide line, the waste generator's policy on the waste treatment and the delivery to a disposal facility, etc. For example, it might be desirable that a waste generator purchases two 450 keV mobile system to examine the drums containing low density waste, and that outsourcing examination for the high density drums, if all NDT items such as quantitative analysis for 'free standing water' and 'void fraction', and confirmation of contents in drum have to be characterized. However, one 450 keV mobile system seems to be required to test only the contents in 13,000 drums per year.

• Tuberculosis and Respiratory Diseases
• /
• v.65 no.6
• /
• pp.471-475
• /
• 2008

Background: In order to achieve a maintenance level and to prevent hemorrhagic complications, regular monitoring of the INR is mandatory for patients on oral anticoagulation therapy (OAT). A point-of-care instrument for INR monitoring is convenient for users, but the accuracy of the results has been controversial, and so this calls for exact evaluation of the point-of-care instrument that is used for INR monitoring. Methods: From Aug 2007 through Feb 2008, 85 patients on OAT among the all the patients who were admitted to Soonchunhyang University Bucheon Hospital were involved in this study. Parallel measurements of the PT INR were performed using a CoaguChek-XS and, a CA-7000 laboratory reference instrument and the results were analyzed. In addition, the patients' clinical data, including the diagnosis and the frequency and interval of the INR measurements, were also analyzed. Results: Of the 85 patients, 25 were admitted more than once to undergo INR testing and the mean interval between testing was 8.6 weeks with 39% and 38% of the tests being less than INR 2 units with using the CoaguChek-XS and the reference method, respectively. The coefficients of variation of CoaguChek-XS were 4.50 and 2.45 for the high and low INR patients, respectively. An excellent correlation was found between the two methods with a $R^2$ of 0.966 (p<0.001). Through Bland-Altman analysis, the mean INR difference between the two methods was 0.13 with the limit of agreement being -0.47~+0.72 with a 95% confidence interval. CoaguChek-XS was shown to overestimate the INR value for patients with an increasing INR, as compared to the reference method. Conclusion: CoaguChek-XS demonstrated great precision and accuracy for patients on OAT when compared to the laboratory INR results. Accordingly, the instrument should help to monitor the INR in the patients on OAT.

• Journal of Korea Multimedia Society
• /
• v.14 no.1
• /
• pp.54-75
• /
• 2011

PoC(Push-to-talk Over Cellular) is an integrated technology of group voice calls, video calls and internet based multimedia services. If a PoC user can not participate in the PoC session for various reasons such as an emergency situation, lack of battery capacity, then the user can use the PoC Box which has a similar functionality to the MM Box in the MMS(Multimedia Messaging Service). The RTSP(Real-Time Streaming Protocol) method is recommended to be used when there is a transmission session between the PoC box and a terminal. Since the existing VOD service uses a wired network, the packet size of RTSP-based VOD service is huge, however, the PoC service has wireless communication environments which have general characteristics to be used in RTSP method. Packet loss in a wired communication environments is relatively less than that in wireless communication environment, therefore, a buffering latency occurs in PoC service due to a play-out delay which means an asynchronous play of audio & video contents. Those problems make a user to be difficult to find the information they want when the media contents are played-out. In this paper, the following techniques and methods were proposed and their performance and superiority were verified through testing: cross-over dual reception buffering technique, advance partition multi-reception buffering technique, and on-demand multi-reception buffering technique, which are designed for effective picking up of information in media content being transmitted in short amount of time using RTSP when a user searches for media, as well as for reduction in playback delay; and same-priority packetization transmission method and priority-based packetization transmission method, which are media data packetization methods for transmission. From the simulation of functional evaluation, we could find that the proposed multiple receiving buffering and packetizing methods are superior, with respect to the media retrieval inclination, to the existing single receiving buffering method by 6-9 points from the viewpoint of effectiveness and excellence. Among them, especially, on-demand multiple receiving buffering technology with same-priority packetization transmission method is able to manage the media search inclination promptly to the requests of users by showing superiority of 3-24 points above compared to other combination methods. In addition, users could find the information they want much quickly since large amount of informations are received in a focused media retrieval period within a short time.

• Journal of Food Hygiene and Safety
• /
• v.25 no.3
• /
• pp.238-244
• /
• 2010

Currently, in vitro suspension tests using tubes are used as a authorized test method for sanitizers and disinfectants. However, the methods could not accurately assess the efficacy of sanitizers and disinfectant on the food-contacted surfaces in the field. This study evaluated the effectiveness of 5 kinds of representative sanitizers and disinfectants against E. coli and S. aureus to compare three quantitative surface testing methods that have been internationally standardized. As a result, the ASTM E2111-05 (ASTM(1)) test method obtained 5.18 $\pm$ 0.03 and 5.27 $\pm$ 0.04 log cfu/carrier reduction in dealing with E. coli and S. aureus, respectively, the ASTM E2197-02 (ASTM(2)) test method obtained 4.63 $\pm$ 0.04 and 3.97 $\pm$ 0.03 log cfu/carrier reduction and the CEN EN 13697 test method should 6.14 $\pm$ 0.05 and 5.31 $\pm$ 0.10 log cfu/carrier reduction in clean condition (CEN(1)) but 4.37 $\pm$ 0.02 and 4.06 $\pm$ 0.01 log cfu/carrier reduction in dirty condition (CEN(2)). Among them, CEN(1) showed the highest bactericidal effects, whereas ASTM(2) and CEN(2) revealed low performance (p < 0.05). In conclusion, the bactericidal effects of the ASTM(2) method and the CEN EN 13697 method adopting stainless steel were lower than the ASTM(1) method, which uses glass. The effectiveness assessment results among nationally accredited test methods were different each other. This implies that they could not fit for in the accurate evaluation of sanitization and disinfection on food-contact surfaces in practical food-processing fields. These results could be used as a basic data for establishment of an official surface test methods applicable in the field.

• Journal of the Korean Arthroscopy Society
• /
• v.9 no.2
• /
• pp.162-166
• /
• 2005

Purpose: The purpose of this study were to evaluate the results of arthroscopic PCL reconstruction and posterolateral structure reconstruction. Materials and Methods: We performed 10 cases of arthrocopic PCL and posterolateral structure reconstruction using allo-achilles tendon. The average follow-up period was 25 months. We performed KT-2000 testing and posterior drawer test for posterior instability and tibial external rotation test for posterolateral rotatory instability, and measure Tegner and Lysholm score preoperatively and compared these with the results of a final evaluation in each cases. Results: The Preoperative average KT-2000 tests was 7.1 mm, posterior drawer test was Grade III and tibial external rotation test was positive at both 30 and 90 degrees of knee flexion in all cases. Preoperative average Lysholm score was 65.9 and Tegner score was 3.1. At the final evaluation, an average KT-2000 test was 2.2 mm, posteior drawer test, Grade 0 was 2 cases, Grade 1.4 cases, Grade II, 3 cases, Grade III, 1 cases. The tibial external rotation test at both 30 and 90 degrees of knee flexion was positive in 1 cases and positive at only 90 degrees in 2 cases. Lysholm score was 87.6 and Tegner score was 5.7. The objective and subjective score of final evaluation is increased in compare with preoperative one. Conclusion: Arthrocopic PCL and posterolateral structure reconstruction using allo-achilles tendon is one of the good surgical treatment method in patients having posterior and posterolateral rotatory instability.

• Journal of Venture Innovation
• /
• v.6 no.2
• /
• pp.41-65
• /
• 2023

This study was conducted to empirically analyse the factors that influence SMEs' intention to adopt ESG. For this purpose, we first derived the variables of usefulness of ESG and ease of adoption. In addition, we adopted CEO's will because of the importance of CEO's role in decision-making in SMEs. In addition, we added customer's request, government support, and credit evaluation reflection as institutional factors for ESG management. To examine the mediating role of attitudes and employees' innovation resistance in these relationships and how they affect ESG adoption, we set up a research model. These factors were used in the empirical analysis with 368 valid responses from the survey. Hierarchical regression analysis method using SPSS 24.0 was used for statistical analysis, and Process Macro 4.0 based on SPSS 24 was used for mediation and moderation effects. The results of the empirical analysis of this study showed that the usefulness of ESG adoption, ease of adoption, CEO's will, customer's request, government support, and credit evaluation reflection all had a positive and significant effect on the intention to adopt ESG management. In particular, among the variables affecting ESG adoption, CEO's will was found to be the most influential. Attitudes were also found to play a mediating role between the influencing factors and intention to adopt ESG management, as well as the mediating effect of employee' innovation resistance. The academic implications of this study include the identification and empirical testing of each of the influencing variables of ESG management adoption in the scarce literature on ESG in SMEs, and the prioritisation of the influence of these factors on adoption intention, which can be used to promote the adoption of ESG management. In terms of practical implications, it is important for SMEs to have a win-win relationship with large corporations, an ecosystem such as government support, in order to improve CEO awareness and motivate the CEO's will, and for smooth introduction of ESG management, it is necessary to find ways to reduce resistance through sufficient communication with organizational members to make them aware of the need.

• Journal of the HCI Society of Korea
• /
• v.9 no.2
• /
• pp.41-51
• /
• 2014

In mobile content services like apps for smart mobile devices in specific, there has been a growing interest in evaluating UX quality to make sure that it provides better experience to users and consequently, secures competitiveness in a market. In that sense, usability testing has been considered as one method that enables designers and design managers to evaluate UI quality before they launch their service. However, those designers have been faced with a following fundamental question to be answere d : Is good UX design a good business? In other words, can well-designed service, which has good usability, actually satisfy target users and improve competitiveness in a market? There is no doubt that usability is one important factor perceived by users. However, it has a limit in terms of evaluating UX quality in macro level, as it mostly focuses on ease of use and efficiency of performing tasks, but does not cover other possible experiential factors, which also can be perceived by users, such as market situation and preexistence experience. Therefore, this research aims to identify key experiential factors in using mobile content services, and establish service UX index model that enables to measure perceived user satisfaction, and identify how UX design contributes to the satisfaction in quantitative way.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.2
• /
• pp.37-44
• /
• 2018

Ballasted track has been widely used due to its flexibility. However, the plastic deformation of ballasted track causes the evolution of track geometrical errors, and hence it requires continuous maintenance; increase in number of trains, weight, and speed expedites maintenance frequency and cost as well. Ballast stiffness is well-known as an indicator of design and maintenance. In this regard, this paper aims to suggest the method to measure ballast track stiffness using light-weight deflectometer (LWD) and thus verify its applicability as a maintenance measure. Preliminary field tests determined simple field testing protocol to measure track stiffness. The apparent ballast stiffness by LWD shows good corelation with TQI (Track Quality Index) and maintenance length. That is, as average of apparent stiffness increase, TQI and tamping length decrease exponentially. Therefore, apparent stiffness can be used as an index for ballast condition assessment.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.1
• /
• pp.113-123
• /
• 2016

This study was to investigate the antifungal activity of A. holophylla essential oil against dermatophytes, such as Epidermophyton floccosum, Trichophyton mentagrophytes and Trichophyton rubrum, and to determine the potential effective compound as dermatitis treatment. To evaluate the potential antifungal activities of A. holophylla essential oil and its fractions, paper disc diffusion and agar dilution method tested with morphological observation. Also, their major constituents were analyzed by GC/MS. To determine synergic effects of active ingredient from A. holophylla essential oil were carried out by checkerboard microtiter plate testing. The morphological changes of the dermatophytes exposed to active fraction G4 were observed by electron microscopes. As the results, the highest activities were identified in the fraction containing ${\alpha}$-bisabolol. A mixture of ${\alpha}$-bisabolol and bornyl acetate showed the synergy effects, expressing high potential effects. Also, morphological observation using electron microscopes showed a dramatic changes of cell membrane of E. floccosum and T. rubrum exposed to fraction G4 containing ${\alpha}$-bisabolol. In conclusion, A. holophylla essential oil and its constituents were expected to be used as antifungal agent or raw material for dermatitis therapy.