• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1465-1469
• /
• 2003

In general satellite verification process, the AOCS (Attitude & Orbit Control Subsystem) should be verified through several kinds of verification test which can be divided into two major category like FBT (Fixed Bed Test) and polarity test. And each test performed in different levels such as ETB (Electrical Test Bed) and satellite level. The test method of FBT is to simulate satellite dynamics with sensors and actuators supported by necessary environmental models in ETB level. The VDS (Vehicle Dynamic Simulator) try to make the real situation as possible as the on-board processor will undergo after launch. The purpose of FBT test is to verify that attitude control logic function and hardware interface is designed as expected with closed loop simulation. The VDS is one of major equipments for performing FBT and consists of software and hardware parts. The VDS operates in VME environments with target board, several commercial boards and custom boards based on the VxWorks real time operating system. In order to make time synchronization between VDS and satellite on-board processor, high reliable semaphore was implemented to make synchronization with the interrupt signal from on-board processor. In this paper, the real-time operating environment used on VDS equipment is introduced, and the hardware and software configurations of VDS summarized in the systematic point of view. Also, we try to figure out the operational concept of VDS and AOCS verification test method with close-loop simulation.

• KIEAE Journal
• /
• v.7 no.4
• /
• pp.135-140
• /
• 2007

In this study we settled the trouble of the MgO board of existence by this research. We changed the wooden one of the main ingredient of a board to a perlite and a mineral particle in the aluminum hydroxide group and proceeded with a study to physical character and fire resistance efficiency improvement. The result yellowing phenomenon could be improved and it was possible to reduce size decrease of pin hole and the frequency of occurrence. We found out that the in case of absorbed amount added 5~8% corresponding to the weight decreases the acrylic group emulsion suddenly. So this product is improved with the bending strength and water-resistance. After behavior stop time measurement of a mouse for experiments was measured at the time of a gas harmful effect test, an improved MgO board appeared more highly for an average of 138 seconds compared with a board of existence.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.2
• /
• pp.35-41
• /
• 2011

Recently, board level solder joint reliability performance of IC packages during drop impact becomes a great concern to semiconductor and electronic product manufacturers. The handheld electronic products are prone to being dropped during their useful service life because of their size and weight. The IC packages are susceptible to solder joint failures, induced by a combination of printed circuit board (PCB) bending and mechanical shock during impact. The board level drop testing is an effective method to characterize the solder joint reliability performance of miniature handheld products. In this paper, applying the JEDEC (JESD22-B111) standard present a finite element modeling of the FBGA. The simulation results revealed that maximum stress was located at the outermost solder ball in the PCB or IC package side, which consisted well with the location of crack initiation observed in the failure analysis after drop reliability tests.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.1
• /
• pp.119-126
• /
• 2005

The objective of this paper is to investigate the lining board's capacity for the static load. The test is to inspect the possibility of retrofit and efficiency, which is required to upgrade the structure's capacity and to examine the effects of the improvements of specimen by using structural analysis, and static loading test, respectively. As the result of static loading test for measured stresses and deflections. H type lining board take sufficient load carrying capacity and high stiffness which likes ultimate load, displacement, and bending stresses of intermediate span and top, bottom flange more than 3 times channel type lining board.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.58 no.1
• /
• pp.85-93
• /
• 2022

In this study, we investigated how satisfaction with on-board training had an effect on career motivation of the trainees. For this purpose, satisfaction for on-board training and career motivation were used as variables. Satisfaction for on-board training were classified into education, environment and operation, and then measurement items were composed. Career motivation consisted of career identity, career insight and career resilience. To establish and test nine hypotheses, a questionnaire survey was conducted by 57 trainees who participated in the Gyeongsang National University on-board sailing training in 2021. To analyze the questionnaire responses, frequency analysis, factor analysis, multiple regression analysis and paired sample t-test were used. As a result of factor analysis, six factors for satisfaction for on-board training were derived. Among the factors, it was analyzed that satisfaction with assignments, the satisfaction with accommodation, and the satisfaction with the adequate condition of facilities and equipment had a significant effect on career motivation. In addition, it was found that career motivation significantly increased through on-board training as a result of comparing the difference between the averages of career motivation before and after on-board training.

• Progress in Superconductivity and Cryogenics
• /
• v.13 no.1
• /
• pp.12-16
• /
• 2011

In this paper, the prototype of the HTS motor with an on-board cryocooler, is fabricated and tested. The overall system is composed of the stator with conventional copper winding, the rotor with superconductor, and the rotating cryocooler designed from the on-board concept. The rotor is fabricated as the race-track coil with 2G, YBCO tape and contacts with the on-board cryocooler while being rotated together. An inline-type pulse tube refrigerator is used as the on-board cryocooler. The cryocooler is fabricated from optimal process to satisfy the structure and thermal stability of the on-board system. Each component is integrated according to carefully defined sequence. Specially, a combining method of torque tubes is an important part for sustaining stability of the rotor and the cryocooler. In the rotating test, the HTS motor is successfully operated with 240 rpm of rotating speed when 75 A current is supplied to the superconducting rotor. In this paper, potential problems of the HTS motor system using the on-board cryocooler are proposed and solved, and realistic possibility of this concept is also confirmed.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.2
• /
• pp.71-77
• /
• 1994

A serious of study is carried out to practical use of the three-slot cambered otter board improved by the authors. As the first step, we designed main plates, slots and accessories, such as holding plate, fan-shaped towing plate, normans, center ring, etc. Standing on this design, we made the simple cambered and three-slot cambered model otter board with accessories in a linear scale 6:1. and carried out model test to examine the efficiency of these boards. The obtained results can be summarized as follows: 1. On the simple cambered board with accessories, the values of the maximum shear coefficient($C _{LX}$ ). drag coefficient(($C _{D}$) and hydrodynamic efficiency($C _{L}$/$C _{D}$ ) are 1.39, 0.56, 2.48 at $22^{\circ}$ of the angle of stall respectively. 2. On the three-slot cambered board with accessories, $C _{LX}$/$C _{D}$ and $C _{I}$/$C _{D}$ are 1.67, 0.92, 1.82 at $32^{\circ}$ of the angle of stall respectively. 3.$C _{LX}$ of board with accessories is smaller 10~12% than that of only the main plate, and the angle of stall is almost same. 4. $C _{LX}$ and the angle of stall of the three-slot cambered board with accessories are greater 20% and $10^{\circ}$ than that of the simple cambered board respectively.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.3
• /
• pp.193-199
• /
• 2016

This study is a research about performance of fireproof board using industrial waste such as oyster shell and dry process bottom ash through the heating test and conclusions were obtained as follows. Test samples show back side temperatures as follows : in $300^{\circ}C$, $103.1{\sim}125.1^{\circ}C$, in $600^{\circ}C$, $201.1{\sim}210.1^{\circ}C$, in $900^{\circ}C$, $249.2{\sim}276.9^{\circ}C$. In the test, temperature increases of specimens of fireproof board are kept at certain temperatures hence it could be concluded that the specimens withstand high temperatures. According to the test, it could be concluded that fireproof board made by smaller particles shows better performance up to $600^{\circ}C$ while at higher temperatures, fireproof board made by bigger particles shows better performance. It is estimated that fireproof board made by particles of bigger size has more pore structure and it delays heat conduction.

• Journal of the Korea Safety Management & Science
• /
• v.5 no.1
• /
• pp.115-128
• /
• 2003

To comparison the surface treatment methods of stone board materials, the results of Dorry's abrasive test were 23.4 for water-jet system and 18.9 for flame-burner system. Therefore abrasive hardness, the stone board materials by the water-jet system was greater than one by flame-jet system. As a result of Shore's hardness test, the stone board materials by water-jet system was twice greater than one by flame-jet system. Authors carried out microscopic observation to survey a defection of the composition minerals for two methods, but all of the both methods have not founded a defection. Therefore, the stone board materials by water-jet system was greater durability than one by flame-jet for the surface treatment methods.

• Journal of the Korean Society for Railway
• /
• v.12 no.5
• /
• pp.670-677
• /
• 2009

This paper is a study of testing on-board signalling equipment in advanced high speed rail at the maximum speed of 400km/h. The on-board signalling equipment in advanced high speed rail provides operating information to the driver when operating at ATC, ATS, and ATP sections, and maintains safety from driver oversight, signalling equipment malfunction, natural disasters and so on. Since the testing train performance of advanced high speed rail at 400km/h must include the function test of on-board signalling equipment, this thesis focuses on the function test of on-board signalling equipment and analyze the necessity of the test at the maximum speed. Finally, it is suggested to change some infrastructure and to use specific test methods to test the train performance at the maximum speed in high speed line ATC section.