• 한국구조물진단유지관리공학회 논문집
• /
• 제21권1호
• /
• pp.15-22
• /
• 2017

본 논문은 바탕면의 함수조건에 따른 보수재료로서 MKPC의 인발 부착강도, 전단 부착강도, 계면 부착강도를 폴리머 시멘트 모르타르, 에폭시 모르타르와 비교 분석하였다. 그 결과 MKPC는 PC 및 MKPC와 비교하여 바탕면 함수조건에 따른 부착성능의 변화가 상대적으로 작은 것으로 나타났다. 또한 MKPC의 경우 절건 바탕면에서의 부착성능은 무기계 보수재료인 폴리머 시멘트 모르타르와 비교하여 우수한 특성을 지니고 있으며, 습윤 바탕면에서의 부착성능은 폴리머 시멘트 모르타르와 유사한 수준을 보이고 있으나 에폭시 모르타르와 비교하여 우수한 특성을 지니는 것으로 나타났다.

• 대한치과보존학회:학술대회논문집
• /
• 대한치과보존학회 2001년도 추계학술대회(제116회) 및 13회 Workshop 제3회 한ㆍ일 치과보존학회 공동학술대회 초록집
• /
• pp.558.1-558
• /
• 2001

Flowable resin composite is a relatively new restorative material. It has been reported that a low viscosity, low modulus intermediate resin applied between the bonding agent and restorative resin act as an "elastic buffer" that can relieve contraction stress. This in-vitro study aimed to evaluate the effect of flowable composite resin as a restorative material on regional tensile bond stredgth to cervical wedge shaped cavity walls. (omitted)

• Restorative Dentistry and Endodontics
• /
• 제28권5호
• /
• pp.378-384
• /
• 2003

This study evaluated the influence of a desensitizer(MS coat) on microtensile bond strength of different adhesives:a three-step adhesive(All-Bond 2), a two-step adhesive(Single Bond), a one-step adhesive(One-up Bond F). Non-caries extracted human molars were used. Dentin surface was obtained by horizontal section on mid-portion of crown using a water-cooled low speed diamond saw. Teeth were randomly divided into 6 group. AMO(MS coat + All Bond), SMO(MS coat + Single Bond)- and OMO(MS coat + One-up Bond F)-dentin surface were treated with 17% EDTA before bonded adhesive. AMX-, SMX- and OMX-dentin surface were bonded with All-Bond 2, Single Bond and One-up Bond F, respectively. with no previous treatment with MS coat and 17% EDTA. About 1cm high resin composite($Z-250^{TM}$) were incrementally build-up on the treated surface. The specimens for the microtensile test were serially sectioned perpendicular to the adhesive layer to obtain $0.7{\times}0.7mm$ sticks. 30 sticks were prepared from each group. After that. tensile bond strength for each stick was measured with Microtensile Tester at a 1mm/min crosshead speed. Fractured dentin surfaces were observed under the SEM. The results were statistically analysed by using a One-way ANOVA and Tukey's test(p<0.05). Value in MPa were: $AMO-44.35{\pm}13.21;{\;}SMO-39.35{\pm}13.32;{\;}OMO-31.07{\pm}10.25;{\;}AMX-49.22{\pm}16.38;{\;}SMX-56.02{\pm}13.35;{\;}OMX-72.93{\pm}16.19$. Application of MS coat reduced microtensile bond strengths of both Single Bond and One-up Bond F, whereas microtensile bond strengths of All-Bond 2 were not affected significantly.

• The Journal of Advanced Prosthodontics
• /
• 제12권4호
• /
• pp.189-196
• /
• 2020

PURPOSE. The aim of the present study was to investigate the effects of surface treatments on the bond strengths between polymer-containing restorative materials and two dual-cure resin cements. MATERIALS AND METHODS. In the present study, rectangular samples prepared from Lava Ultimate (LU) and Vita Enamic (VE) blocks were used. The specimen surfaces were treated using CoJet sandblasting, 50 ㎛ Al₂O₃ sandblasting, % 9 HF (hydrofluoric) acid, ER,Cr:YSGG laser treatment, and Z-Prime. Dual-cure resin cements (TheraCem and 3M RelyX U 200) were applied on each specimen's treated surface. A micro-tensile device was used to evaluate shear bond strength. Statistical analysis was performed using the SAS 9.4v3. RESULTS. While the bond strength using TheraCem with LU or VE was not statistically significant (P=.164), the bond strength using U200 with VE was statistically significant (P=.006). In the TheraCem applied VE groups, Z-Prime and HF acid were statistically different from CoJet, Laser, and Sandblast groups. In comparison of TheraCem used LU group, there was a statistically significant difference between HF acid and other surface treatments. CONCLUSION. The bonding performance between the restorative materials and cements were material type-dependent and surface treatment had a large effect on the bond strength. Within the limitations of the study, the use of both U200 and TheraCem may be suggested if Z-prime was applied to intaglio surfaces of VE. The cementation of LU using TheraCem is suitable after HF acid conditioning of the restoration surfaces.

• Smart Structures and Systems
• /
• 제17권4호
• /
• pp.593-610
• /
• 2016

In this study, an innovative and smart glass fiber-reinforced polymer (GFRP) hybrid bar was developed for stronger durability of concrete structures. As comparing with the conventional GFRP bar, the smart GFRP Hybrid bar can promise to enhance the modulus of elasticity so that it makes the cracking reduced than the case when the conventional GFRP bar is used. Besides, the GFRP Hybrid bar can effectively resist the corrosion of conventional steel bar by the GFRP outer surface on the steel bar. In order to verify the bond performance of the GFRP hybrid bar for structural reinforcement, uniaxial pull-out test was conducted. The variables were the bar diameter and the number of strands and pitch of the fiber ribs. Tensile tests showed a excellent increase in the modulus of elasticity, 152.1 GPa, as compared to that of the pure GFRP bar (50 GPa). The stress-strain curve was bi-linear, so that the ductile performance could be obtained. For the bond test, the entire GFRP hybrid bar test specimens failed in concrete splitting due to higher shear strength resulting in concrete crushing as a function of bar deformation. Investigation revealed that an increase in the number of strands of fiber ribs enhanced the bond strength, and the pitch guaranteed the bond strength of 19.1 mm diameter hybrid bar with 15.9 mm diameter of core section of deformed steel the ACI 440 1R-15 equation is regarded as more suitable for predicting the bond strength of GFRP hybrid bars, whereas the CSA S806-12 prediction is considered too conservative and is largely influenced by the bar diameter. For further study, various geometrical and material properties such as concrete cover, cross-sectional ratio, and surface treatment should be considered.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.361-364
• /
• 2006

In this study, six specimens were prepared for two type FRP sheets(carbon and polyacetal) to evaluate the behavior of FRP-concrete interfacial bond. A direct tensile test was conducted and the test results show that fiber type influences both bond strength and the shape of strain distribution. The failure mode for carbon type specimens seems to bond failure between concrete and FRP, but for polyacetal type indicates interface failure between FRP and expoxy. The local bond stress-slip relations were obtained from test results, and it was shown good shape for the polyacetal type. But for the carbon type it was scattered.

• 콘크리트학회논문집
• /
• 제14권3호
• /
• pp.315-320
• /
• 2002

본 연구에서는 고로슬래그 미분말을 이용한 SBR혼입 폴리머 시멘트 콘크리트의 강도 성상에 미치는 고로슬래그 치환율 및 폴리머 결합재비의 영향에 대하여 구명하였다. 그 결과, 고로슬래그 미분말을 이용한 SBR혼입 폴리머 시멘트 콘크리트의 압축, 인장 및 휨강도는 폴리머-결합재비 및 고로슬래그 치환율의 증가에 따라 증가하였으며, 고로슬래그 치환율 40%에서 가장 높은 강도를 나타내었다. 특히 고로슬래그 치환율 40%의 SBR혼입 폴리머 시멘트 콘크리트의 인장 및 휨강도는 폴리머 미혼입의 강도보다 약 2배 이상의 높은 강도를 보였다. 이와 같이 높은 강도의 발현은 SBR 폴리머의 높은 인장강도와 SBR라텍스의 혼입에 의한 시멘트 수화물과 골재간의 접착성이 개선되었기 때문이라 판단된다.

• Journal of Welding and Joining
• /
• 제23권6호
• /
• pp.67-71
• /
• 2005

This paper is concerned with a study on fracture strength of composites in an adhesive single lap joint. The tests were carried out on joint specimens made with hybrid stacked composites consisting of the polyester and bamboo natural fiber layer. The main objective of this work was to evaluate the fracture properties adjacent to adhesive bonded joint of natural fiber reinforced composite specimens. From the results, natural fiber reinforced composites have lower tensile strength than the original polyester. But tensile-shear strength of natural fiber reinforced composites with bamboo layer far from adhesive bond is as high as that of the original polyester adhesive bonded joints. Spew filet at the end of the overlap reduced the stress concentration at the bonded area. Spew fillet and position of bamboo natural fiber layer have a peat effect on the tensile-shear strength of natural fiber reinforced composites including adhesive bonded joints.

• International Journal of Concrete Structures and Materials
• /
• 제18권1E호
• /
• pp.29-34
• /
• 2006

Elastic modulus, tensile and bond capacities are important factors for developing an effective reinforcing action of a flexural member as a reinforcing material for concrete structures. Reinforcement must have enough bond capacity to prevent the relative slip between concrete and reinforcement. This paper presents an experimental study to clarify the bond capacity of prestressed carbon fiber reinforced polymer(CFRP) rod manufactured by an automatic assembly robot. The bond characteristics of CFRP rods with different pitch of helical wrapping were analyzed experimentally. As the result, all types of CFRP rods show a high initial stiffness and good ductility. The mechanical properties of helical wrapping of the CFRP rods have an important effect on the bond of these rods to concrete after the bond stress reached the yield point. The stress-slip relationship analyzed from the pull-out test of embedded cables within concrete was linear up to maximum bond capacity. The deformation within the range of maximum force seems very low and was reached after approximately 1 mm. The average bond capacity of CF20, CF30 and CF40 was about 12.06 MPa, 12.68 MPa and 12.30 MPa, respectively. It was found that helical wrapping was sufficient to yield bond strengths comparable to that of steel bars.

• 대한치과보철학회지
• /
• 제47권2호
• /
• pp.232-239
• /
• 2009

연구목적: 많은 의치 환자들은 의치의 유지력, 안정성 그리고 저작기능을 향상시키기 위해 의치접착제를 사용하고 있다. 이상적인 의치접착제는 독성이나 자극이 없고, 구강점막에 편안함을 제공하고, 나쁜 냄새나 맛이 없어야 한다. 의치접착 크림의 세포독성 여부를 확인하고, 의치접착제의 효과와 시간에 따른 유지력의 변화를 알아보고자 하였다. 연구재료 및 방법: 의치접착크림의 세포독성 여부를 알아보기 위해 mouse 섬유아세포를 이용한 MTT 시험을 통해 의치접착크림의 농도와 1일에서 4일까지의 시간에 따른 세포독성 여부를 평가하였다. 의치 접착제가 유지력 향상에 미치는 효과와 시간에 따른 유지력의 변화를 알아보기 위해 무치악 덴티폼과 이에 맞는 의치상을 제작하여 의치 접착제 적용 후 3일까지의 인장결합강도를 측정하였다. 결과: 1. 의치접착크림은 농도와 시간에 따라 세포독성이 관찰되는 것은 없었다. 2. 의치접착크림과 인공타액을 동시에 사용한 경우 통계학적으로 가장 높은 인장 결합강도를 나타내었고, 의치접착크림을 단독으로 사용한 경우보다 인장 결합강도가 통계학적으로 유의성 있게 높았다. 이는 인공타액과 의치접착크림의 인장 결합강도의 단순 합계보다 높았다. 3. 의치접착크림과 인공타액을 동시에 사용한 군에서 도포 후부터 1시간 후까지 인장 결합강도는 최대치를 기록하였고 3시간부터 인장 결합강도는 점차 감소하기 시작하여 12시간 후는 최대 인장 결합강도의 70%, 1일후에50%까지 감소하였다. 이상의 결과를 토대로 의치접착크림은 1일에서 4일까지 세포독성이 없었고 의치의 유지력을 향상시키는데 효과적이며, 타액과 같이 작용하여 효과를 더 발휘할 수 있었다. 향후 장기적인 사용에 따른 다양한 세포독성 실험과 접착력의 감소에 대한 연구가 필요하리라 사료된다.