• 소성∙가공
• /
• 제16권4호
• /
• pp.317-322
• /
• 2007

In order to investigate the cause and condition of fluting in tangential bending of low carbon steel sheet, an analytic analysis, an experiment and a series of finite element analysis for bending process were done. The fluting in bended sheet was related with the yield point elongation of material. Due to the yield point elongation, unstable plastic hinge was occurred in course of bending of elastic perfectly plastic sheet. According to the analysis and computational results, lower yield point elongation than 5% was required to prevent fluting in 0.5-0.6t sheet in $15{\sim}25mm$ radius bending. The tendency of fluting occurrence was reduced as decreasing the radius of bending, increasing thickness of bended sheet, and removing irregularity in sheet and bending processes.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.336-339
• /
• 2007

In order to investigate the cause of fluting in tangential bending of low carbon steel sheet, an analytic analysis, an experiment and a series of finite element analysis for bending process were done. The fluting in bended sheet was due to the yield point elongation of material. Due to the yield point elongation, unstable plastic hinge was occurred in course of bending of elastic perfectly plastic sheet. According to the analysis and computational results, lower yield point elongation than 5% was required to prevent fluting in $0.5{\sim}0.6t$ sheet in $15{\sim}20mm$ radius bending.

• 소성∙가공
• /
• 제14권4호
• /
• pp.375-383
• /
• 2005

The shear spinning process, where the plastic deformation zone is localized in a very small portion of the workpiece, shows a promise for increasingly broader application to the production of axially symmetric parts. In this paper, the three components of the working force are calculated by a newly proposed deformation model in which the spinning process is understood as shearing deformation after uniaxial yielding by bending, and shear stress, $\tau_{rz}$, becomes k, yield limit in pure shear, in the deformation zone. The tangential force are first calculated and the feed force and the normal force are obtained by the assumption of uniform distribution of roller pressure on the contact surface. The optimum contact area is obtained by minimizing the bending energy required to get the assumed deformation of the blank. The calculated forces are compared with experimental results. A comparison shows that theoretical prediction is reasonably in good agreement with experimental results

• Journal of Mechanical Science and Technology
• /
• 제20권6호
• /
• pp.806-818
• /
• 2006

The shear spinning process, where the plastic deformation zone is localized in a very small portion of the workpiece, shows a promise for increasingly broader application to the production of axially symmetric parts. In this paper, the three components of working force are calculated by the newly proposed deformation model in which the spinning process is understood as shearing deformation after uniaxial yielding by bending, and shear stress, $\tau_{rz}$ becomes $\kappa$, yield limit in pure shear, in the deformation zone. The tangential forces are first calculated and the feed forces and the normal forces are obtained by the assumption of uniform distribution of roller pressure on the contact surface. The optimum contact area is obtained by minimizing the bending energy required to get the assumed deformation of the blank. The calculated forces are compared with experimental results. A comparison shows that theoretical prediction is reasonably in good agreement with experimental results.

• Structural Engineering and Mechanics
• /
• 제17권1호
• /
• pp.1-14
• /
• 2004

Numerical solution to linear bending analysis of circular plates is obtained by the method of harmonic differential quadrature (HDQ). In the method of differential quadrature (DQ), partial space derivatives of a function appearing in a differential equation are approximated by means of a polynomial expressed as the weighted linear sum of the function values at a preselected grid of discrete points. The method of HDQ that was used in the paper proposes a very simple algebraic formula to determine the weighting coefficients required by differential quadrature approximation without restricting the choice of mesh grids. Applying this concept to the governing differential equation of circular plate gives a set of linear simultaneous equations. Bending moments, stresses values in radial and tangential directions and vertical deflections are found for two different types of load. In the present study, the axisymmetric bending behavior is considered. Both the clamped and the simply supported edges are considered as boundary conditions. The obtained results are compared with existing solutions available from analytical and other numerical results such as finite elements and finite differences methods. A comparison between the HDQ results and the finite difference solutions for one example plate problem is also made. The method presented gives accurate results and is computationally efficient.

• 대한기계학회논문집
• /
• 제14권3호
• /
• pp.547-553
• /
• 1990

본 연구에서는 알루미나 세라믹(Al$_{2}$O$_{3}$)재료와 순수구리를 티타늄 용자재로써 접합한 브레이징 접합물내의 냉각후 잔류응력을 유한요소법으로 사용하여 해석하였다.

• 한국강구조학회 논문집
• /
• 제15권5호통권66호
• /
• pp.509-518
• /
• 2003

본 논문에서는 강 콘크리트 경계면에 대한 비선형 해석 모델을 바탕으로 합성 구조체에 대한 비선형 구조해석을 실시하여 강 콘크리트 경계면을 모사한 인터페이스 요소에 발생하는 접선응력선 상대슬립 분포 등 합성 구조체의 경계면 거동 특성을 해석적으로 규명하였다. 연구결과 본 논문의 해석 모델인 합성 바닥판에서는 T형강-콘크리트 경계면 보다는 하부강판-콘크리트 경계면에서 접선응력의 증가가 빠르게 나타났으며, 하부강판-콘크리트 경계면에서도 인장부보다는 중립부 경계면에서 접선응력의 증가가 빠르게 진행되었다. 횡방향으로는 하중재하 위치에서 외부 측면으로 갈수록 접선응력이 완화되는 현상을 나타내었으며 종방향으로는 중앙부에서 최소, 지지점에서 $0.6{\sim}0.7L$ 지점에서 최대를 나타냈으며 이후 지지점으로 갈수록 감소하는 경향을 나타내었고, 하층이 증가하면서 경계면의 파괴가 최고 접선응력지점에서 전체영역으로 점차 확대되는 경향을 나타내었다. 이상의 연구결과는 합성 구조체의 경계면의 거동 특성과 하중전달 메카니즘을 이해하고 합리적인 전단연결재 설계를 위한 바탕을 제공할 것으로 기대된다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(5)
• /
• pp.189-192
• /
• 2002

This paper has been studied the movement of snake robot. In this paper we developed a simulator to simulate the creeping locomotion of a snake robot. This Robot makes possible to analyze the creeping locomotion with the normal-direction slip coupled to gliding along the tangential direction. Using the nonslip condition of the wheels, the robot gains propulsion by means of constrained forces on the wheels caused by bending the joints. The results of simulations show that smooth lateral undulatory motion is achived.

• 소성∙가공
• /
• 제24권4호
• /
• pp.241-247
• /
• 2015

In order to prevent shape defects such as fluting and stretcher strains during press forming of aged low carbon steel sheets, roller leveling conditions for reducing yield point elongation were studied. Yield point elongations of leveled sheets were determined as a function of leveling, which is defined as the plastic fraction or the ratio of plastically deformed part in sheet thickness section to the whole thickness of the sheet. By adjusting this plastic fraction during leveling to more than 78%, yield point elongation in the leveled sheets was reduced so no fluting occurred during subsequent tangential bending. Stretcher strains can be avoided by leveling the sheet to an 84% plastic fraction condition.

• Earthquakes and Structures
• /
• 제7권2호
• /
• pp.233-250
• /
• 2014

In this paper, a three dimensional soil-structure interaction (SSI) is numerically simulated using finite element method in order to analyse the foundation moments in annular raft of tall slender chimney structures incorporating the effect of openings in the structure and the effect of soil flexibility, when the structure-soil system is subjected to El Centro (1940) ground motion in time domain. The transient dynamic analysis is carried out using LS-DYNA software. The linear ground response analysis program ProShake has been adopted for obtaining the ground level excitation for different soil conditions, given the rock level excitation. The radial and tangential bending moments of annular raft foundation obtained from this SSI analysis have been compared with those obtained from conventional method according to the Indian standard code of practice, IS 11089:1984. It is observed that tangential and radial moments increase with the increase in flexibility of soil. The analysis results show that the natural frequency of chimney decreases with increase in supporting soil flexibility. Structural responses increase when the openings in the structure are also considered. The purpose of this paper is to propose the need for an accurate evaluation of the soilstructure interaction forces which govern the structural response.