• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.7
• /
• pp.481-485
• /
• 2003

Amorphous silicon (a-Si:H) based TFT process has been studied at the maximum temperature of 15$0^{\circ}C$ with 25${\mu}{\textrm}{m}$ thick flexible and adhesive tape type polyimide foil substrate, which has benefit on handling a rugged, flexible plastic substrate trough sticking simply it to glass. This paper summarize the process procedure of the TFT on the plastic substrate and shows its electrical characteristics in comparison with glass substrate using primarily the ON/OFF current ratio and the field effect mobility as the quality criterion. The a-SiN:H coating layer played an important role in decreasing surface roughness of plastic substrate, so leakage current of TFT was decreased and mobility was increased. The results show that high quality a-Si:H TFTs can be fabricated on the plastic substrates through coating a rough plastic surface with a-SiN:H.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.4
• /
• pp.1803-1811
• /
• 2011

We have analyzed the electrical defect detection mechanism using low energy microcolumn on the TFT substrate for TFT-LCD. In this study, we have acquired the SEM images of the various pixel defects for 7-inch TFT substrate by scanning of low energy electron beam in the high vacuum chamber. Futhermore, we have interpreted the defect detection mechanism through the correlations between the SEM images and electrical behaviors of the defective pixels. As a result, we obtained consistent results as the follows. We can confirm that the SEM images using low energy electron beam are significantly affected by the space charge effect.

• Electrical & Electronic Materials
• /
• v.9 no.1
• /
• pp.30-37
• /
• 1996

Previously, crystallization of a-Si:H films on glass substrates were limited to anneal temperature below 600.deg. C, over 10 hours to avoid glass shrinkage. Our study indicates that the crystallization is strongly influenced by anneal temperature and weakly affected by anneal duration time. Because of the high temperature process and nonconducting substrate requirements for poly-Si TFTs, the employed substrates were limited to quartz, sapphire, and oxidized Si wafer. We report on poly-Si TFT's using high temperature anneal on a Si:H/Mo structures. The metal Mo substrate was stable enough to allow 1000.deg. C anneal. A novel TFT fabrication was achieved by using part of the Mo substrate as drain and source ohmic contact electrode. The as-grown a-Si:H TFT was compared to anneal treated poly-Si TFT'S. Defect induced trap states of TFT's were examined using the thermally stimulated current (TSC) method. In some case, the poly-Si grain boundaries were passivated by hydrogen. A-SI:H and poly-Si TFT characteristics were investigated using an inverted staggered type TFT. The poly -Si films were achieved by various anneal techniques; isothermal, RTA, and excimer laser anneal. The TFT on as grown a-Si:H exhibited a low field effect mobility, transconductance, and high gate threshold voltage. Some films were annealed at temperatures from 200 to >$1000^{\circ}C$ The TFT on poly-Si showed an improved $I_on$$I_off$ ratio of $10_6$, reduced gate threshold voltage, and increased field effect mobility by three orders. Inverter operation was examined to verify logic circuit application using the poly Si TFTs.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1466-1469
• /
• 2008

We have fabricated 2.5 inch QQCIF AM-OLED panel driven by ZnO-TFT on a plastic substrate for the first time. The number of photo mask for the whole panel process was 5 and the TFT structure was top gate with active protection layer as a first gate insulator. Optimizing the process for the substrate buffer layer, active layer, ZnO protection layer, and gate insulator was key factor to achieve the TFT performance enough to drive OLED. The ZnO TFT has mobility of $5.4\;cm^2/V.s$, turn on voltage of -6.8 V, sub-threshold swing of 0.39 V/decade, and on/off ratio of $1.7{\times}10^9$. Although whole process temperature is below $150^{\circ}C$ to be suitable for the plastic substrate, performance of ZnO TFT was comparable to that fabricated at higher temperature on the glass.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.10-10
• /
• 2009

We have fabricated transparent and flexible thin film transistor(TFT) on polyethylene terephthalate(PET) substrate using Zinc Oxide (ZnO) and Indium Tin Oxide (ITO) film as active layer and electrode. The transfer printing method was used for printing the device layer on target plastic substrate at room temperature. This approach have an advantage to separate the high temperature annealing process to improve the electrical properties of ZnO TFT from the device process on plastic substrate. The resulting devices on plastic substrate presented mechanical and electrical properties similar with those on rigid substrate.

• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.933-936
• /
• 2000

N-channel poly-Si TFT, processed by Solid Phase Crystalline(SPC) on a glass substrate, has been investigated by measuring its electrical properties before and after stressing. It is observed that the threshold voltage shift due to electrical stress varies with various stress conditions. Threshold voltages measured in 1.5um and 3um poly-Si TFT’s are 3.3V, 37V respectively. With the threshold voltage shift, the degradation of transconductance and subthreshold swing is also observed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.247-249
• /
• 2008

Low Temperature a-Si:H TFT on stainless steel substrate has been developed for the flexible electrophoretic display. Stability of low temperature a-Si:H TFT is more important point than its initial device characteristics. Thus, we have studied device characteristics of low temperature a-Si:H TFT in terms of stability for driving electrophoretic display.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.962-964
• /
• 2007

A 14.1-inch reflective type Thin Film Transistor-Electric Phoretic Display was developed at the esolution of 1280 x 900 lines on plastic substrate. All of the processes of TFT were carried out below $100\;^{\circ}C$ on PES plastic films. The process conditions of TFT were optimized for large area TFT-LCD on plastic substrate. At $60^{\circ}C$ high temperature during 160hours, TFT does not delaminate and IV characteristic is also satisfied.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.341-341
• /
• 2011

최근 AMOLED 구동이 가능한 소자에 대한 연구가 활발히 진행중이다. AMOLED구동 가능소자는 LTPS TFT, a-Si TFT, OTFT, Oxide TFT가 있으며 그 중에서 현재 대부분 LTPS TFT를 사용하고 있다. LTPS TFT는 높은 전자 이동도와 안정성을 가지고 있기 때문에 현재 각광 받는 AMOLED에 잘 맞는다. 하지만 LTPS TFT는 고비용, 250$^{\circ}C$ 이상의 공정온도, Substrate가 Glass, Metal로 제한 된다는 문제점이 있으며, 균일성이 낮고 현재 대면적 기술이 부족한 상태이다. 해결방안으로 AMOLED를 타겟으로 하는 Oxide TFT 기술이 떠오르고 있다. Oxide TFT는 이동도가 높고 저온공정이 가능하며 Substrate로 Plastic 기판을 사용할 수가 있어 차후에 Flexible 소자로서의 적용이 가능하다. 또한 기존의 진공장비 사용대신 용액공정이 가능하여 장비사용시간 및 절차를 단축시킬 수 있어 비용적인 유리함을 가지고 있다. Oxide TFT는 단결정 산화물과 다결정 복합 산화물 두 가지 범주를 가지고 있다. Oxide TFT의 재료물질은 ZnO, ZTO, IZO, SnO2, Ga2O3, IGO, In2O3, ITO, InGaO3(ZnO)5, a-IGZO이 있다. 본 연구에서는 산화물질 중 하나인 ZTO를 이용하여 TFT 소자를 제작하였다. 산화물 특성상 열처리 온도에 따라 형성되는 결정의 정도가 다르기 때문에 온도 및 시간 변수에 따른 ZTO의 특성변화에 초점을 맞추어 연구함으로서 최적화된 조건을 찾고자 실험을 진행하였다. 실험을 위한 기판으로 n-type wafer을 사용하였다. PE-CVD 장비를 이용하여 SiNx를 120 nm 증착하고, ZTO 용액을 spin-coating을 이용하여 channel layer을 형성하였다. 균일하게 형성된 ZTO의 결정을 위하여 200$^{\circ}C$, 300$^{\circ}C$, 400$^{\circ}C$, 500$^{\circ}C$에서 1시간, 3시간, 6시간, 10시간의 온도 및 시간 변수를 두어 공기 중에서 열처리 하였다. ZTO는 약 30 nm 두께로 형성되었다. Thermal evaporator를 이용하여 Source, Drain의 알루미늄 전극을 형성하고, wafer 뒷면에는 Silver paste를 이용하여 Gate전극을 만들었다. 제작된 소자를 dark room temperature에서 측정하였다.

• Electrical & Electronic Materials
• /
• v.19 no.9
• /
• pp.28-32
• /
• 2006

A 7.0-inch transmissive type plastic TFT-LCD was developed at the resolution of 640 $\times$ 3 $\times$ 480 lines (114ppi). All of the processed of TFT, color filter and LC were carried out below $130^{\circ}C$ on PES plastic films. The process conditions of TFT, color filter and LC were optimized for large area TFT-LCD on plastic substrate. The backplane and the color filter was strongly adhered while the panel was bending by using holding spacers.