• Journal of Sensor Science and Technology
• /
• v.14 no.6
• /
• pp.369-373
• /
• 2005

High quality CdTe single crystal for the solar cell fabrication was grown by vertical Bridgman method. The etch pits patterns of (111) surfaces of CdTe etched by Nakagawa solution was observed the (111)A compesed of Cd atoms with typical triangle etch pits of pyramid mode. From the photoluminescence measurement on (111)A, we observed free exciton ($E_{x}$) existing only high quality crystal and neutal acceptor bound exciton ($A^{0}$,X) having very strong peak intensity. Then, the full width at half maximum and binding energy of neutral acceptor bound exciton were 7 meV and 5.9 meV, respectively. By Haynes rule, an activation enery of impurity was 59 meV. Therefore, the origins on impurity level acting as a neutral acceptor were associated Ag or Cu elements.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.6
• /
• pp.1146-1150
• /
• 2009

Cadmium telluride (CdTe) is one of the most attractive photovoltaic materials due to its low cost, high efficiency and stable performance in physical, optical and electronic properties. Few researches on the influences of uniform surface on the photovoltaic characteristics in large-area CdTe solar cell were not reported. As the preceding study of the effects of thickness-uniformity on the photovoltaic characteristics for the large-area CdTe thin film solar cell, chemical mechanical polishing (CMP) process was investigated for an enhancement of thickness-uniformity. Removal rate of CdTe thin film was 3160 nm/min of the maximum value at the 200 $gf/cm^2$ of down force (pressure) and 60 rpm of table speed (velocity). The removal rate of CdTe thin film was more affected by the down force than the table speed which is the two main factors directly influencing on the removal rate in CMP process. RMS roughness and peak-to-valley roughness of CdTe thin film after CMP process were improved to 96.68% and 85.55%, respectively. The optimum process condition was estimated by 100 $gf/cm^2$ of down force and 60 rpm of table speed with the consideration of good removal uniformity about 5.0% as well as excellent surface roughness for the large-area CdTe solar cell.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.279-283
• /
• 2003

In this study, ZnTe : S single crystal thin films substituted by sulfur were grown on GaAs (100) substrates by hot-wall epitaxy. The photoluminescence (PL) characteristics of ZnTe : S single crystal thin films was measured to investigate the effects due to sulfur atoms in the ZnTe layer. The Peak of 2.339 eV identified as the isoelectronic center was observed in low temperature PL spectrum, but PL spectra which the origin had not been well-explained were not observed. Temperature dependence of PL intensities of the light hole free exciton was explained by extrinsic self-trapping. Besides it is reported that the emission lines near absorption edge at room temperature were observed.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.1
• /
• pp.40-45
• /
• 2016

Recently, $Bi_2Te_3$-based alloys are the best thermoelectric materials near to room temperature, so it has been researched to achieve increased figure of merit(ZT). Ternary compounds such as Bi-Te-Se and Bi-Sb-Te have higher thermoelectric property than binary compound Bi-Te and Sb-Te, respectively. Compared to DC plating method, pulsed electrodeposition is able to control parameters including average current density, and on/off pulse time etc. Thereby the morphology and properties of the films can be improved. In this study, we electrodeposited n-type ternary Cu-doped $Bi_2(Te-Se)_3$ thin film by modified pulse technique at room temperature. To further enhance thermoelectric properties of $Bi_2(Te-Se)_3$ thin film, we optimized Cu doping concentration in $Bi_2(Te-Se)_3$ thin film and correlated it to electrical and thermoelectric properties. Thus, the crystal, electrical, and thermoelectric properties of electrodeposited $Bi_2(Te-Se)_3$ thin film were characterized the XRD, SEM, EDS, Seebeck measurement, and Hall effect measurement, respectively. As a result, the thermoelectric properties of Cu-doped $Bi_2(Te-Se)_3$ thin films were observed that the Seebeck coefficient is $-101.2{\mu}V/K$ and the power factor is $1412.6{\mu}W/mK^2$ at 10 mg of Cu weight. The power factor of Cu-doped $Bi_2(Te-Se)_3$ thin film is 1.4 times higher than undoped $Bi_2(Te-Se)_3$ thin film.

• Journal of the Korean Chemical Society
• /
• v.53 no.5
• /
• pp.530-535
• /
• 2009

Dicyclohexyl telluride was obtained in a high yield by the reaction of cyclohexyl bromide with NaTeH(prepared in situ) in an aqueous ethanolic solution. A series of new organotelluronium salts of the general formula ${(cyclo-C_6H_11)}_2Te(R)X$ (where R = $CH_3$, X = I (1); R = $C_2H_5$, X = Br(2); R = $C_2H_5$, X = I (3); R = C_3H_5$, X = Br (4)) were prepared by the reaction of ${(cyclo-C_6H_11)}_2Te$ with the corresponding alkyl halide. Reaction of 1 with NaBPh4 gave compound 5 ( i.e. R = CH3, X = BPh4 ‒) in 78% yield. Reaction of ${(cyclo-C_6H_11)}_2Te$ with benzyl bromide and 4-bromophenacyl bromide gave unexpectedly dibenzylcyclohexyltelluronium bromide (6) and bis(4-bromophenacyl)cyclohexyltelluronium bromide (7), respectively. Reaction of 6 with NaBPh4 gave the corresponding tetraphenylborate derivative (8) in high yield. $^1H$ NMR studies revealed that in $CDCl_3$solution compound 1 eliminated alkyl halide. Conductivity, IR, $^1H\;and\;^{13}C$ NMR and thermal data for the new compounds are presented and discussed.

• Journal of Powder Materials
• /
• v.13 no.5 s.58
• /
• pp.313-320
• /
• 2006

The present study is to analyze the thermoelectric properties of $Bi_{0.4}Sb_{1.6}Te_3$ thermoelectric materials fabricated by the mechanical grinding process. The $Bi_{0.4}Sb_{1.6}Te_3$ powders were prepared by the combination of mechanical milling and reduction treating methods using simply crushed pre-alloyed $Bi_{0.4}Sb_{1.6}Te_3$ powder. The mechanical milling was carried out using the tumbler-ball mill and planetary ball mill. The tumbler-ball milling had an effect on the carrier mobility rather than the carrier concentration, whereas, the latter on the carrier concentration. The specific electric resistivity and Seebeck coefficient decreased with increasing the reduction-heat-treatment time. The thermal conductivity continuously increased with increasing the reduction-heat-treatment time. The figure of merit of the $Bi_{0.4}Sb_{1.6}Te_3$ sintered body prepared by the mechanical grinding process showed higher value than one of the sintered body of the simply crushed powder.

• The KIPS Transactions:PartC
• /
• v.11C no.6 s.95
• /
• pp.815-820
• /
• 2004

For providing high quality-guaranteed service over Internet, traffic engineering based on an MPLS technology is being introduced. MPLS traffic engineering performs the computation on the path guaranteeing service`s quality and the reservation on network resources by an MPLS signaling protocol. As one of MPLS signaling protocol, RSVP-TE protocol transmits and receives periodic refresh messages for maintaining the path of a traffic flow. Such characteristic gives a heavy processing overhead to routers for maintaining states of large number of paths. In this paper, we propose a scalable implementation approach for RSVP-TE without dramatically increasing processing overhead. And we eval-uate the processing overhead on periodic messages by implementing the RSVP-TE protocol and the reduction mechanism of periodic messages.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.666-672
• /
• 1996

The optical property of CdTe thin film is important for applications such as the compound semiconductor type solar cells. CdTe films are prepared by RF sputtering at various substrate temperature between $25^{\circ}C$ and $300^{\circ}C$, then, annealed in argon gas environment at $400^{\circ}C$. The annealing process of the thin film caused variation in the film structure and the composition of films. The deformation of CdTe thin film was observed by X-ray diffractometry. After annealing, the grain size increased and the portion of the non-crystalline CdTe reduced. Futhermore, the structure of sputtered CdTe film grown at the substrate temperature more than $250^{\circ}C$ was enhanced in the (111) direction of zincblend structure. There was a discrepancy, in the spectroscopic ellipsometer spectrum, between the single crystal CdTe and the sputtered CdTe thin films, especially in the region over 3.2eV. An oxidation layer was found on the CdTe thin film by spectroscopic ellipsometry analysis.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.253-253
• /
• 2011

ZnTe semiconductor is very attractive a material for optoelectronic devices in the visible green spectral region because of it has direct bandgap of 2.26 eV. The prototypes of ZnTe light emitting diodes (LEDs) have been reported [1], showing that their green emission peak closely matches the most sensitive region of the human eye. The optoelectronic properties of ZnTe:O film allow to expect a large optical gain in the intermediate emission band, which emission band lies about 0.4-0.6 eV below the conduction band of ZnTe [2]. So, the ZnTe system is useful for the production of high-efficiency multi-junction solar cells [2,3]. In this work, the ZnTe:O thin films were deposited on Al2O3 substrates by using the radio frequency magnetron sputtering system. Three sets of samples were prepared using argon and oxygen as the sputtering gas. The deposition chamber was pre-pumped down to a base pressure of 10-7 Torr before introducing gas. The deposition pressure was fixed at 10-3 Torr throughout this work. During the ZnTe deposition, the substrate temperature was 300 oC. The optical properties were also investigated by using the ultraviolte-visible (UV-Vis) spectrophotometer.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.2
• /
• pp.114-118
• /
• 2017

Bismuth telluride ($Bi_2Te_3$) and its alloys are well-known thermoelectric materials for ambient temperature applications. In this study, the dissolved Bi-Te precursor solution was used to synthesis metallic $Bi_2Te_3$ powder via ultrasonic spray pyrolysis and reduction process. The droplets of the Bi-Te precursor solution were decomposed to Bi-Te oxide powders by ultrasonic spray pyrolysis. The spherical $Bi_2Te_3$ powders were synthesized by reduction reaction in atmosphere of hydrogen gas at the temperature above $375^{\circ}C$ for 6h. The reduced $Bi_2Te_3$ powders have a mean particle size of $1.5{\mu}m$. The crystal structure of the powder was evaluated by X-Ray diffraction(XRD), and the microstructure with size and shape powders was observed by fieldemission scanning electron microscope(FE-SEM) and transmission electron microscope(TEM).