• Journal of Korean Society of Transportation
• /
• v.15 no.3
• /
• pp.93-109
• /
• 1997

현재 사용되고 있는 신호등 설치기준은 교차로의 형태를 반영하고 있지 않다. 본 논문은 신호 및 비신호 T형 교차로에 대한 현장의 지체도 조사를 바탕으로 첨두시간 교통량을 이용한 T형 교차로의 신호등 설치기준을 개발하였다. 기준설정을 위해 교차로의 평균정지지체 최소화를 평가척도로 사용하였으며 주요 연구결과를 요약하면 다음과 같다. 첫째, T형 교차로의 지체도 모형은 주도로 교통량과 부도로 교통량을 독립변수로 하는 지수함수 형태를 갖는다. 둘째, T형 교차로의 신호등 설치기준은 T형으로 인한 현시의 감소로 MUTCD에서 제시하고 있는 신호등 설치기준과 비교시 타당성 교통량이 높게 나타났다. 셋째, T형 교차로의 신호등 설치를 위한 첨두시 교통량기준 도표를 작성하였으며, 평일의 하루중 주도로(양방향)의 시간당 교통량과 이에 사용하는 부도로의 시간당 교통량의 최대값을 도표에 표시했을 때 접근로 차로수의 조합에 해당하는 기준선의 상위영역에 위치하면 신호등을 설치하는 것이 교차로의 지체도를 최소화시킬수 있다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.4
• /
• pp.595-600
• /
• 2023

In this paper, a modified equations of the T-equivalent circuit of the transmission line with the arbitrary electrical length is suggested. The suggested equations can be calculated without limitation of the equal branch-line. So, a modified T-equivalent circuit can be made with the arbitrary position of the open-stub. Also, the modified T-equivalent circuit can be applied in the arbitrary electrical length and impedance of the transmission line. For example, the λ/4 impedance transformer is converted with 4 divided T-equivalent circuit. The converted λ/4 impedance transformer has the size reduction ratio of 39.4%.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.3
• /
• pp.403-411
• /
• 2002

This paper described the ultimate strength and deformation limit of welded T-joints in cold-formed square hollow sections. Previous studies showed that the T-joint has an obvious peak load. with the failure mode of chord-web buckling at a ratio of branch width to chord width ($\beta$) of above 0.8. Similar to a T-joint with chord-flange failure mode, the strength at a certain deformation limit can be regarded as the ultimate strength of a T-joint Based on the experimental results including tests done by Kato and Zhao, the deformation limit was proposed as 3%B for $10.7{\leq}2{\gamma}(B/T){\leq}42.3$ and $0.8{\leq}{\beta}{\leq}1.0$. The strength formula of CIDECT and those of other researchers were also compared with the test results. Finally, the strength formula based on the column buckling was proposed.

• Journal of Korean Society of Steel Construction
• /
• v.23 no.2
• /
• pp.169-177
• /
• 2011

This paper presents the results of the systematic finite element analysis of the in-plane bending moment of T-joints subjected to cyclic loadings. T-joints were fabricated using high-strength, circular, hollow sections. Three-dimensional, nonlinear finite element models of the welded T-joints were constructed to investigate the strength, rotational-stiffness characteristics, and failure modes. A wide scope of structural behaviors explain the influence of the joint geometric parameters, such as the chord and brace wall slenderness ratios and the ratio of the brace to the chord diameter, as well as the yield strength ratios and compressive-chord-stress effects on the ultimate in-plane bending moment capacity of the T-joint.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.1
• /
• pp.133-140
• /
• 2010

Five strengthened columns and an unstrengthened column were tested under constant axial load and cyclic lateral loads to examine the seismic performance of the unbounded strengthening procedure using wire ropes and T-plates. Main variables considered were the presence of mortar cover for strengthening steel element and anchorage method of T-plate. Test results clearly showed that T-plates having a proper anchorage contribute to transfer of applied moment as well as enhancement of ductility of reinforced concrete columns. However, T-plate not anchored fully into a column base can seldom transfer the externally applied moment, though it highly improves the ductility of column. The presence of mortar cover for strengthening steel elements is significantly effective in enhancing the initial stiffness and flexural capacity of the strengthened columns, but has an adversely effect on enhancing the ductility. The ultimate moment strength predicted from the extended section laminae method in better agreement with test results compared with predictions obtained using stress black specified in ACI 318-05.

• Journal of the Korea Concrete Institute
• /
• v.14 no.6
• /
• pp.1001-1009
• /
• 2002

The objective of this study is to determine the range of confinement (or the transverse reinforcement of the reinforced concrete structural walls with the T-shaped cross section subjected to cyclic lateral loads. The range of confinement for transverse reinforcement is related to the location of neutral axis and determined by the magnitude and distribution of compressive strain. The compressive strain depends on the ratio of wall cross sectional area to the floor-plan area, the aspect ratio, configuration, the axial load, and the reinforcement ratios. By affection of flange, the neutral axis appears different depending on positive and negative forces and because of this reason, when web and flange are subjected to compressive stress, the range of confinement for the transverse reinforcement of T-shaped walls would shows different result. Therefore this experimental research focused on the structural characteristics of T-shaped walls and suggested the neutral axis depth through comparing the results of this study with sectional analysis.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.576-579
• /
• 2007

마이크로스트립으로 급전되는 슬롯 안테나를 소형화하기 위해 폴디드 슬롯과 T형 마이크로스트립 선로로 구성된 안테나 구조를 제안하였다. 전형적인 마이크로스트립으로 급전된 슬롯 안테나와 성능(안테나 크기, 슬롯 길이, 대역폭 등)을 비교하였으며, T형 마이크로스트립선로를 이용한 급전선로의 임피던스정합 방법에 대하여 설명하였다. 제안된 구조로 유전제기판상에 2.45GHz 대역 WLAN용 안테나를 설계 및 제작하였으며 특성 실험(반사손실, 부사패턴)을 통해 연구의 타당성을 확인하였다.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.4 s.65
• /
• pp.467-474
• /
• 2003

Composite action can be achieved by providing shear connectors between the steel top flange and concrete topping. Composite sections are stiffer than the sum of the individual stiffness of slab and beam. They can therefore carry heavier loads or similar loads with appreciably smaller deflection. They are also less prone to transient vibration. In this study, T-type Steel Composite beam (TSC-beam) was developed and tested. The test results of TSC beam were compared with the theoretical results based on composite actions.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.169-175
• /
• 2006

In this paper, a microstrip patch antenna with the T-shaped slits is designed and fabricated for GPS. The resonant frequency of the microstrip patch antenna with the slits is lower than that of a microstrip patch antenna without the slits so it can be reduced the size of patch. In order to calculate resonant frequency of the microstrip patch antenna with the slits, the resonant frequency formulas are derived from the surface current distribution on microstrip patch antenna. Using the Ensemble 6.0 simulation tool, the accuracy of approximate equations is verified. The microstrip patch antenna with the slits is designed by using these equations. The size of the designed antenna with T-shaped slits can be reduced to 29% compared with that without the slits. The microstrip patch antenna with slits have a very narrow bandwidth. In order to improve the narrow bandwidth of microstrip patch antennas with the slits, a microstrip patch antenna with rectangular slot is proposed. As the result of the measurements, the resonant frequency of the proposed microstrip patch antenna with the T-shaped slits is 1.575GHz and the bandwidth is about 50MHz.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.2
• /
• pp.311-318
• /
• 2002

This paper described the ultimate strength and deformation limit of welded T-joints in cold-formed square hollow sections. Previous studies showed that the strength of a T-joint still increases with increasing deformations at a ratio of branch width to chord width (${\beta}$) of below 0.8. Therefore, the strength at a certain deformation (chord flange indentation) limit can be regarded as the ultimate strength of a T-joint. The chord flange failure modes were investigated for the ratio of branch width to chord width (${\beta}$) and the ratio of chord width to chord web thickness (B/T). Experimental results including tests done by Kato proposed a deformation limit of 3%B for $16.7{\leq}B/T{\leq}41.6$ and $0.27{\leq}{\beta}{\leq}0.8$. The strength formula of CIDECT and other researchers were compared with the test results. Finally, the strength formula based on yield-line theory was proposed.