• Journal of information and communication convergence engineering
• /
• 제14권4호
• /
• pp.268-271
• /
• 2016

An efficient inductive switching noise suppression technique for mixed-signal integrated circuits (ICs) using standard CMOS digital technology is proposed. The proposed design technique uses a parallel RC circuit, which provides a damping path for the switching noise. The proposed design technique is used for designing a mixed-signal circuit composed of a ring oscillator, a digital output buffer, and an analog noise sensor node for $0.13-{\mu}m$ CMOS digital IC technology. Simulation results show a 47% reduction in the on-chip inductive switching noise coupling from the noisy digital to the analog blocks in the same substrate without an additional propagation delay. The increased power consumption due to the damping resistor is only 67% of that of the conventional source damping technique. This design can be widely used for any kind of analog and high frequency digital mixed-signal circuits in CMOS technology

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1891-1895
• /
• 2003

Switch-mode power supplies (SMPS) have become a major source of conducted electromagnetic interference (EMI) which is the combination between differential mode (DM) noise and common mode (CM) noise. This paper presents the conducted EMI reduction approach in flyback switched mode power supply by rerouting for circuit balance to reduce common mode noise. And differential mode noise can be reduce by adding $c_x$ capacitor across the input power line, and passive element to the gate drive of switching device MOSFET to slow down the switching times. This combination of our approach is the effective way to reduce the conducted EMI and it is also a cost effective for product design

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 F
• /
• pp.2106-2107
• /
• 1998

This paper analyzes the sources of EMI noise, and Presents the noise reduction method using the modulation of switching frequency. Modulating the switching frequency makes the noise of side bands by shattering emission spectrum, and then can reduce the size of EMI filter at input line of power supply.

• 한국조명전기설비학회지:조명전기설비
• /
• 제11권6호
• /
• pp.64-73
• /
• 1997

RPWM(Random Pulse Width Modulation)은 인버터의 스위칭 주파수를 랜덤(random)하게 변화시킴으로써 고조파 및 소음의 파워 스펙트럼을 광대역에 분산시켜 사람이 불쾌하게 느낄 수 있는 전자기적 가청 소음을 줄이기 위한 PWM 기법으로써 근래에 매우 각광받고 있다. 본 연구에서는 삼각파(반성파, carrier wave)의 주파수를 랜덤하게 변화시키는 방식의 RPWM에 의한 인버터 유도전동기 구동 장치를 구성하였다. 무항실에서 실험 측정한 소음의 파워 스펙트럼으로부터, 소음원에 대한 분석과 삼각파 주파수 변화 폭에 따른 스위칭 주파수대 소음의 저감 효과를 분석하였다. 고속의 DSP TMS320C31을 사용하여 속도 제어와 더불어 RPWM이 실시간적으로 가능하도록 하여, 부하 조건이 다양하게 변화하는 구동 장치에서도 삼각파 주파수의 중심 주파수 및 대역폭을 자유롭게 변화시킴으로써 효과적으로 스위칭 주파수대 가청 소음을 저감하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 학술대회 논문집 전문대학교육위원
• /
• pp.98-101
• /
• 2002

The switching-mode power converter has been widely used because of its features of high efficiency and small weight and size. These features are brought by the ON-OFF operation of semiconductor switching devices. However, this switching operation causes the surge and EMI(Electromagnetic Interference) which deteriorate the reliability of the converter themselves and entire electronic systems. This problem on the surge and noise is one of the most serious difficulties in AC-to-DC converter. In the case of carrier frequency selection, output-voltage of steady state and transient state is fully regulated. A RPWM control method was proposed in order to smooth the switching noise spectrum and reduce it's level. Experimental results are verified by converter operating at 300V/1kW with 5%${\sim}$30% white noise input. Spectrum analysis is performed on the Phase current and the CM noise voltage. The former is measured with Current Probe and the latter is achieved with USN. which are connected to the spectrum analyzer respectively.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.493-498
• /
• 2004

The EMI noise source in a switching mode power supply is dominated by a common mode noise. If we can understand the common mode noise occurring mechanism, it is resulted to find out the method to suppress the EMI noise source in the switching mode power supply. The common mode noise is occurring mostly due to circuit is unbalanced which is caused by the capacitive coupling to frame ground, which passes through a heatsink of the switching devices. This research paper presents a new effective balancing method of buck converter circuit by mean of grounding the parasitic and compensation capacitors in correct proportion which is called that the common mode impedance balance (CMIB). The CMIB can be achieved by source, transmission line and termination balanced, such balancing, the common mode current will be cancelled out in the frame ground. The greatly reduced common mode noise can be confirmed by the experimental results.

• 전력전자학회논문지
• /
• 제3권4호
• /
• pp.287-297
• /
• 1998

RPWM(Random Pulse Width Modulation)은 인버터의 스위칭 주파수를 랜덤하게 변화 시킴으로써 전압, 전류의 고조파 및 소음의 스펙트럼을 광대역에 분산시키는 PWM 기법이다. 스위칭 주파수 또는 펄스의 위치를 랜덤하게 변화시켜 고조파의 불연속적인 이산치 성분을 넓은 영역에 분산시켜 EMI, 진동 등에 좋은 효과를 낼 수 있을 뿐만 아니라, 전력소자의 스위칭에 의해 발생하는 가청 스위칭 소음을 저감할 수 있으므로 근래에 매우 각광 받고 있다. 본 연구에서는 펄스의 위치를 랜덤하게 함으로써 가청 스위칭 소음을 저감할 수 있는 새로운 RPPWM(Random Position Pulse Width Modulation) 방식의 제안 및 구현하였다. 제안된 방식은 각 3상 펄스들의 위치를 변조 구간 내의 임의의 위치에 랜덤하게 배치함으로써 RPWM을 구현하는 방식이다. 이를 위하여 16bit 공성능 마이크로 컨트롤러의 C167을 사용하여, 공각 벡터 변조에 의하여 각 변조 구간에서의 듀티비를 구한 후, 랜덤수 발생기를 이용하여 균일한 분포로 각 상의 펄스를 배치하였다. 그리고 제안된 RPPWM을 이용하여 실험한 결고, 전압, 전류 및 소음의 스텍트럼이 광대역화 되어 전력소자의 스위칭에 의해 발생하는 전동기의 가청 스위칭 소음이 현저히 저감 됨을 확인하였다.

• 전자공학회논문지
• /
• 제50권1호
• /
• pp.97-101
• /
• 2013

There is a growing need for optical communication systems that convert large volumes of data to optical signals and that accommodate and transmit the signals across long distances. Digital optical communication consists of a master unit (MU) and a slave unit (SU). The MU transmits data to SU using digital optical signals. However, digital optical units that are commercially available or are under development transmit data using two's complement representation. At low input levels, a large number of SSOs (simultaneous switching outputs) are required because of the high rate of bit switching in two's complement, which thereby increases the power noise. This problem reduces the overall system capability because a DSP (digital signal processor) chip (FPGA, CPLD, etc.) cannot be used efficiently and power noise increases. This paper proposes a change from two's complement to a more efficient method that produces less SSO noise and can be applied to existing digital optical units.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 학술대회 논문집 전문대학교육위원
• /
• pp.154-158
• /
• 2006

The switching-mode power converter has been widely used because of its features of high efficiency and small weight and size. These features are brought by the ON-OFF operation of semiconductor switching devices. However, this switching operation causes the surge and EMI(Electromagnetic Interference) which deteriorate the reliability of the converter themselves and entire electronic systems. This problem on the surge and noise is one of the most serious difficulties in AC-to-DC converter. Random Pulse Width Modulation (RPWM) is peformed by adding a random perturbation to switching instant while output-voltage regulation of converter is performed. RPWM method for reducing conducted EMI in single switch three phase discontinuous conduction mode boost converter is presented. The more white noise is injected, the more conducted EMI is reduced. But output-voltage is not sufficiently regulated. This is the reason why carrier frequency selection topology is proposed. In the case of carrier frequency selection, output-voltage of steady state and transient state is fully regulated. A RPWM control method was proposed in order to smooth the switching noise spectrum and reduce it's level. Experimental results are verified by converter operating at 300v/1kW with $5%{\sim}30%$ white noise input. Spectrum analysis is performed on the Phase current and the CM noise voltage. The former is measured with Current Probe and the latter is achieved with LISN, which are connected to the spectrum analyzer respectively.

• 전기학회논문지P
• /
• 제51권3호
• /
• pp.120-125
• /
• 2002

The switching-mode power converter has been widely used because of its features of high efficiency and small weight and size. These features are brought by the ON-OFF operation of semiconductor switching devices. However, this switching operation causes the surge and EMI(Electromagnetic Interference) which deteriorate the reliability of the converter themselves and entire electronic systems. This problem on the surge and noise is one of the most serious difficulties in AC-to-DC converter. In the switching-mode power converter, the output voltage is generally controlled by varying the duty ratio of main switch. When a converter operates in steady state, duty ratio of the converter is kept constant. So the power of switching noise is concentrated in specific frequencies. Generally, to reduce the EMI and improve the immunity of converter system, the switching frequency of converter needs to be properly modulated during a rectified line period instead of being kept constant. Random Pulse Width Modulation (RPWM) is performed by adding a random perturbation to switching instant while output-voltage regulation of converter is performed. RPWM method for reducing conducted EMI in single switch three phase discontinuous conduction mode boost converter is presented. The more white noise is injected, the more conducted EMI is reduced. But output-voltage is not sufficiently regulated. This is the reason why carrier frequency selection topology is proposed. In the case of carrier frequency selection, output-voltage of steady state and transient state is fully regulated. A RPWM control method was proposed in order to smooth the switching noise spectrum and reduce it's level. Experimental results are verified by converter operating at 300V/1kW with 5%~30% white noise input. Spectrum analysis is performed on the Phase current and the CM noise voltage. The former is measured with Current Probe and the latter is achieved with LISN, which are connected to the spectrum analyzer respectively.