• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.12
• /
• pp.649-654
• /
• 2003

The simplest method for measuring output currents of the three phase inverters is to measure them with three current sensors such as hall sensors. This method requires at least two current sensors, and these types of sensors are somewhat expensive. More economical method is measuring DC link current with a simple shunt resistor, then, reconstructing output current using the DC link current value and the switching status. However, in low speed region, the measurement becomes difficult and even impossible due to the requirement of minimum switching duration for A/D conversion. These problems can be overcome by limitation of switching duration. Limitation of switching, however, causes voltage and current distortion. Owing to compensation, distortion can be effectively suppressed. However these increase acoustic noise due to increment of current ripple. In this paper, a current measurement method is proposed, which can reduce minimum switching duration resulting in reduction of acoustic noise. The validity of proposed method is confirmed through experiment.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.137-139
• /
• 2005

본 논문에서는 30W급 스위칭형 직류전원장치 (Switching Mode Power Supply : SMPS)에 준공진형 프라이 백 스위칭 레귤레이터(quasi-resonant flyback switching regulator)를 적용하여 방사노이즈(radiation-noise)를 억제한 사례에 대하여 설명하고 있다. 기존의 PI사(社)의 TOP IC 시리즈$^{[1]}$와 같이 보편적으로 사용되고 있는 일명, 하드 스위칭(hard-switching)형 레귤레이터를 사용할 경우, 고속 스위칭시에 스위칭 손실(switching loss)과 스위칭 노이즈(switching noise)가 발생한다. 이로 인하여 SMPS의 발열에 따른 효율저화와 방사 노이즈에 의한 전파방해 등이 문제점이 된다. 본 논문에서는 일본의 Sanken사(社)에서 개발/시판중인 준공진형 스위칭 레귤레이터인 STR-F6000 IC 시리즈$^{[2]}$를 이용하여 프라이백 SMPS를 구성하여 방사노이즈를 저감하였다.

• Journal of Power Electronics
• /
• v.2 no.2
• /
• pp.139-145
• /
• 2002

Because conventional switching converters have been usually using unbalanced circuit topologies, parasitice between the drain/collertor of an active switch and frame ground through its heat sink may generate the commom-mode conducted noise. We have proposed a balanced switching converter circuit, whitch is an effective way to reduce the commom-mode converter version of the balanced switching converter was presented and the mechanism of the commom-mode noise reduction was explained using equivalent circuits. This paper extends the concept of the balanced switch converter circuit and presents a buck-boost converter version of the blanced switching converter. The feature of common-mode niose reduction is confirmed by experimental resuits and the mechanisem of the commom-mode niose reduction is explained using equivalent circuits.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.493-498
• /
• 2004

The EMI noise source in a switching mode power supply is dominated by a common mode noise. If we can understand the common mode noise occurring mechanism, it is resulted to find out the method to suppress the EMI noise source in the switching mode power supply. The common mode noise is occurring mostly due to circuit is unbalanced which is caused by the capacitive coupling to frame ground, which passes through a heatsink of the switching devices. This research paper presents a new effective balancing method of buck converter circuit by mean of grounding the parasitic and compensation capacitors in correct proportion which is called that the common mode impedance balance (CMIB). The CMIB can be achieved by source, transmission line and termination balanced, such balancing, the common mode current will be cancelled out in the frame ground. The greatly reduced common mode noise can be confirmed by the experimental results.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.10
• /
• pp.4930-4951
• /
• 2018

The deep learning based speech enhancement has shown considerable success. However, it still suffers performance degradation under mismatch conditions. In this paper, an adaptation method is proposed to improve the performance under noise mismatch conditions. Firstly, we advise a noise aware training by supplying identity vectors (i-vectors) as parallel input features to adapt deep neural network (DNN) acoustic models with the target noise. Secondly, given a small amount of adaptation data, the noise-dependent DNN is obtained by using $L_2$ regularization from a noise-independent DNN, and forcing the estimated masks to be close to the unadapted condition. Finally, experiments were carried out on different noise and SNR conditions, and the proposed method has achieved significantly 0.1%-9.6% benefits of STOI, and provided consistent improvement in PESQ and segSNR against the baseline systems.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.477-481
• /
• 2009

In this paper the process of transmitting images signal restore to image corrupted by impulse noise proposed switching mean filter. these filter is differential size using the two state noise detection distinguishes noise pixel and noise free pixel. Follow the detected impulse noise density in the image remove the impulse noise using switching mean filter these substituted pixel in order to non-recursive and recursive form from control process of the next pixel comes to be used with neighbor pixel process. Through the simulation, we compared with the existing methods and capabilties.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.6
• /
• pp.44-50
• /
• 2002

A novel technique for minimization of simultaneous switching noise is Presented. Dual Layer Power Line (DLPL) structure i:; newly proposed for a possible silicon realization of a mutual inductor, with which an instant large current in the power line is half-divided flowing through two different, but closely coupled, layers in opposite directions. This mutual inductance between two power layers enables us to significantly reduce the switching noise. SPICE simulations show that with a mutual coupling coefficient higher than 0.8, the switching noise reduces by 63% compared to the previously reported solutions. This DLPL technique can also be applied to PCB artworks.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 1999.11a
• /
• pp.33-36
• /
• 1999

In this paper, we proposed a simultaneous switching noise(SSN) reduction technique in muti-layer beards(MLB) for high-speed digital applications and analyzed them using the Finite Difference Time Domain(FDTD) method. The new method by conductive dielectric substrates reduces SSN couplings and resonances, significantly, which cause series malfunctions in the modem high-speed digital applications.

• Journal of the Korea Safety Management & Science
• /
• v.5 no.2
• /
• pp.199-214
• /
• 2003

With the progress of industrial technology, industrial machinery and home appliances have multi-function and high performances by the electronic control technology. Various results are given from the measuring switching induction noise according to environmental condition and its effects cannot be predicted accurately. Therefore, the output results should be analyzed and applied to practical work. To minimize the false operation, Taguchi Method used to solve the quality problem is adopted to analyze the characteristics within the constrained measuring level.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.3
• /
• pp.115-119
• /
• 2001

This paper presents an efficient and simple method for analyzine maximum simultaneous switching noise (SSN) on ground interconnection networks in CMOS systems. For the derivation of maximum SSN expression, we use ${\alpha}$-power law MOS model and Taylor's series approximation. The accuracy of the proposed method is verified by comparing the results with those of previous researches and HSPICE simulations under the contemporary process parameters and environmental conditions. The proposed method predicts the maximum SSN values more accurately when compared to existing approaches even in most practical cases such that exist some output drivers not in transition.