• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.869-872
• /
• 2005

In this paper we present a switch wrapper for an AMBA AXI, which is an efficient on-chip-network interface compared to bus-based interfaces in a multiprocessor SoC. The AXI uses an idea of NoC to provide the increasing demands on communication bandwidth within a single chip. A switch wrapper for AXI is located between a interconnection network and two IPs connecting them together. It carries out a mode of routing to interconnection network and executes protocol conversions to provide compatibility in IP reuse. A switch wrapper consists of a direct router, AHB-AXI converters, interface modules and a controller modules. We propose the design of a all-in-one type switch wrapper.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.6
• /
• pp.664-670
• /
• 2015

A four-times-VDD switch that supports high and low voltage mode operations is demonstrated in a generic 65 nm logic process. The proposed switch shows the robust operation for supply voltages ranging from VDD to $4{\times}VDD$. A cascaded voltage switch and a voltage doubler based charge pump generate the intermediate supply voltage levels required for the proposed high voltage switch. All the high voltage circuits developed in this work can be implemented using standard logic transistors without being subject to any voltage overstress.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.8
• /
• pp.433-437
• /
• 2000

We fabricated switch module of ATM(Asynchronous Transfer Mode) exchange system with MCM-C(MultiChip Module Co-fired) technology and measured its electrical characteristics. Green tape was used as substrate and Au/Ag paste was used to form the interconnect layers. The via holes were made by drill and filled with metal paste usign screen method. After manufacturing the substrate, chips and passive components were assembled on the substrate. In electrical test, the module showed the output signal of 46.9MHz synchronized with input signal. In the view of substrate size reduction, the area of MCM switch module was 35% of conventional hybrid switch module.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.113-116
• /
• 2003

Confluence buffers and single flux quantum (SFQ) switches are essential components in constructing a high speed superconductive Arithmetic Logic Unit (ALU). In this work, we developed a SFQ confluence buffer and an SFQ switch. It is very important to optimize the circuit parameters of a confluence buffer and an SFQ switch to implement them into an ALU. The confluence buffer that we are currently using has a small bias margin of $\pm$11％. By optimizing it with a Josephson circuit simulator, we improved the design of confluence buffer. Our simulation study showed that we improved bias global margin of 10％ more than the existent confluence buffer. In simulations, the minimal bias margin was $\pm$33％. We also designed, fabricated, and tested an SFQ switch operating in a DC mode. The mask layout used to fabricate the SFQ switch was obtained after circuit optimization. The test results of our SFQ switch showed that it operated correctly and had a reasonably wide margin of $\pm$15％.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.4
• /
• pp.324-333
• /
• 2009

This paper presents a numerical simulation study of the transient behavior of a $2{\times}340MW$ pump-turbine power plant, where the results show an unstable behavior at runaway. First, the modeling of hydraulic components based on equivalent schemes is presented. Then, the 2 pump-turbine test case is presented. The transient behavior of the power plant is simulated for a case of emergency shutdown with servomotor failure on Unit 1. Unstable operation at runaway with a period of 15 seconds is properly simulated using a 1-dimensional approach. The simulation results points out a switch after 200 seconds of the unstable behavior between a period of oscillations initially of 15 seconds to a period of oscillation of 2.16 seconds corresponding to the hydraulic circuit first natural period. The pressure fluctuations related to both the rigid and elastic water column mode are presented for oscillation mode characterization. This phenomenon is described as a switch between a rigid and an elastic water column oscillation mode. The influence of the rotating inertia on the switch phenomenon is investigated through a parametric study.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.936-945
• /
• 2016

Large magnitude common-mode voltage (CMV) and its variation dv/dt have an adverse effect on motor drives that leads to early winding failure and bearing deterioration. For matrix converters, the switch states that connect each output line to a different input phase result in the lowest CMV among all of the valid switch states. To reduce the output CMV for matrix converters, this paper presents a new space vector modulation (SVM) strategy by utilizing these switch states. By this mean, the peak value and the root mean square of the CMV are dramatically decreased. In comparison with the conventional SVM methods this strategy has a similar computation overhead. Experiment results are shown to validate the effectiveness of the proposed modulation method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.3
• /
• pp.188-194
• /
• 2020

This paper presents a high-efficiency Switch Mode Line Transformer (SMLT) composed of load-shared dual modules, which is based on the AC/AC LLC resonant converter. Given that the conventional adaptor is usually composed of two power stages, namely, the PFC and DC/DC converters, its system size can be increased according to the output power. However, given that the proposed SMLT can separate the PFC converter from the adaptor, the size reduction of the system can be achieved. Meanwhile, the SMLT with a single module has the limit of the size reduction because of a high resonant current. Thus, it can be configured with dual or multiple modules to reduce the resonant current. Then, their load sharing can be guaranteed by only the proposed transformer structure without an extra current controller. The validity of the proposed converter is proven through a 850-W prototype.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.11-23
• /
• 2019

In this study, a novel zero voltage zero current transition (ZVZCT) bidirectional DC-DC converter is proposed by employing coupled inductors. This converter can turn the main switch on at ZVZCT and it can turn it off with zero voltage switching (ZVS) for both the boost and buck modes. These characteristics are obtained by using a simple auxiliary sub-circuit regardless of the power flow direction. In the boost mode, the auxiliary switch achieves zero current switching (ZCS) turn-on and ZVS turn off. Due to the coupling inductors, this converter can make further efficiency improvements because the resonant energy in the capacitor or inductor can be transferred to the load. The main diode operates with ZVT turn-on and ZCS turn-off in the boost mode. For the buck mode, there is a releasing circuit to conduct the currents generated by the magnetic flux leakage to the output. The auxiliary switch turns on with ZCS and it turns off with ZVT. The main diode also turns on with ZVT and turns off with ZCS. The design method and operation principles of the converter are discussed. A 500 W experimental prototype has been built and verified by experimental results.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.267-270
• /
• 2000

In this paper, we consider the simple redundant structures with the function of hardware based active/standby control. The system includes two switch modules. The switch module is connected to a data bus, but only the active switch module has control of the data bus. The standby unit takes over the function of the active unit when the active unit failure or mode command are asserted. And this paper illustrate the high-speed router system and the overall redundant system architecture. The proposed redundant architecture for 80G Router system is verified and implemented with experiment.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.298-303
• /
• 2009

A single-switch parallel resonant converter for induction heating is implemented. The circuit consists of an input LC-filter, a bridge rectifier, and a controlled power switch. The switch operates in soft commutation mode and serves as a high frequency generator. The output power is controlled via the switching frequency. A steady state analysis of the converter operation is presented. A closed-loop circuit model is also presented, and the experimental results are compared with the simulation results.