• Electrical & Electronic Materials
• /
• v.10 no.6
• /
• pp.555-561
• /
• 1997

The passivation of n-GaAs(100) surface has investigated by photoreflectance(PR). The surface of the sample was treated with the 0.001 N solution Se/NH$_4$OH. After the surface treatment, the samples were annealed between 400 to $700^{\circ}C$ in a $N_2$atmosphere for 10 min. The intensity of PR signal and period of Franz-Deldysh oscillation(FKO) gradually decreased as the annealing temperature increased. The surface electric field(E$_{s}$) of the sample annealed at $600^{\circ}C$ is obtained 1.34$\times$10$^{5}$ V/cm. This value is 1.97 times less than that of unannealed sample. It has found that the passivation of surface occurred when the surface of the sample had been treated with Se/NH$_4$OH solution and annealed from 500 to $600^{\circ}C$. This result could be due to activation of elemental Se on the surface. It has also found that the elemental Se of the surface diffused about 100 $\AA$ into the bulk GaAs when Se-treated sample was annealed at $600^{\circ}C$.>.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.4
• /
• pp.80-85
• /
• 2007

The passivation is one of the important technologies for protection of the devies from damage. In this paper, we fabricated $0.1{\mu}m\;{\Gamma}$--gate InAIAs/InGaAs metamorphic high electron mobility transistors (MHEMTs) on a GaAs substrate. And then the wafer with MHEMTs was divided into two pieces; one for passivation and another for without passivation experiments. The passivations were done by using both low-k BCB and Si3N4 thin films. DC and RF performances were measured and the results are compared. The MHEMTs with BCB passivation show lower degradation than ones with Si3N4 passivation.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.128.1-128.1
• /
• 2011

In amorphous silicon and crystalline silicon(a-Si:H/c-Si) heterojuction solar cells, intrinsic hydrogenated amorphous silicon(a-Si:H) films play an important role to passivate the crystalline silicon wafer surfaces. We have studied the correlation between the surface passivation quality and nature of the Si-H bonding at the a-Si:H/c-Si interface. The samples were obtained by VHF-CVD under different deposition conditions. The passivation quality and analysis of all structures studied was performed by means of quasi steady state photoconductance(QSSPC) methods and fourier transform infrared spectrometer(FTIR) measurements respectively.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.5
• /
• pp.227-233
• /
• 2015

To reduce the cost of solar electricity, the crystalline-silicon (c-Si) photovoltaic industry is moving toward the use of thinner wafers (100 μm to 200 μm) to achieve a high efficiency. In this field, it is imperative to achieve an effective passivation method to reduce the electronic losses at the c-Si interface. In this article, we review the most promising surface passivation schemes that are available for high-efficiency solar cells.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.892-896
• /
• 2005

In this paper, key issues of stainless steel foil substrates for display applications have been described. We studied and analyzed technical issues on substrate passivation/planarization to control surface roughness and capacitive coupling from conductive substrates. A thick (either multiple or single) passivation/planarization layer needs to be applied on the nonelectronic-grade stainless steel substrate to provide a smooth surface and electrical insulation from the conductive substrate. Especially for large size, high-resolution display applications, low k and thick passivation/planarization layers should be used for appropriate capacitive coupling. Based on our initial study, a unit area capacitance of less than $2nF/cm^2$ of passivation/planarization layers is needed for 32" HD TV OLED displays.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.211-211
• /
• 2012

The electrical loss of the photo-generated carriers is dominated by the recombination at the metal- semiconductor interface. In order to enhance the performance of the solar cells, many studies have been performed on the surface treatment with passivation layer like SiN, SiO2, Al2O3, and a-Si:H. In this work, Al2O3 thin films were investigated to reduce recombination at surface. The Al2O3 thin films have two advantages, such as good passivation properties and back surface field (BSF) effect at rear surface. It is usually deposited by atomic layer deposition (ALD) technique. However, ALD process is a very expensive process and it has rather low deposition rate. In this study, the ICP-assisted reactive magnetron sputtering method was used to deposit Al2O3 thin films. For optimization of the properties of the Al2O3 thin film, various fabrication conditions were controlled, such as ICP RF power, substrate bias voltage and deposition temperature, and argon to oxygen ratio. Chemical states and atomic concentration ratio were analyzed by x-ray photoelectron spectroscopy (XPS). In order to investigate the electrical properties, Al/(Al2O3 or SiO2,/Al2O3)/Si (MIS) devices were fabricated and characterized using the C-V measurement technique (HP 4284A). The detailed characteristics of the Al2O3 passivation thin films manufactured by ICP-assisted reactive magnetron sputtering technique will be shown and discussed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.346-346
• /
• 2009

For high efficiency hetero junction solar cell over 20%, good silicon wafer passivation is one of the most important technological factor. Compared to the conventional PECVD technique, HWCVD has appeared as an promising alternative for high quality passivation layer formation. In this work, HWCVD passivation layer characteristics have been intensively investigated on wafer surface treatment, Hydrogen density in deposited thin layer and thermal effects in deposition process. Comprehensive results of the individual process factors on interface passivation has been discussed and resultant silicon hetero junction solar cell characteristics has been investigated.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.2
• /
• pp.131-135
• /
• 2005

The effect of different surface passivation films on blue or green (465-505 nm) InGaN/GaN multi-quantum well light-emitting diodes (LEDs) die were examined. $SiO_2$ or $SiN_x$ deposited by plasma enhanced chemical vapor deposition, or $Sc_2O_3$ or MgO deposited by rf plasma enhanced molecular beam epitaxy all show excellent passivation qualities. The forward current-voltage (I-V) characteristics were all independent of the passivation film used, even though the MBE-deposited films have lower interface state densities ($3-5{\times}10^{12}\;eV^{-1}\;cm^{-2}$) compared to the PECVD films (${\sim}10^{12}\;eV^{-1}\;cm^{-2}$), The reverse I-V characteristics showed more variation, hut there was no systematic difference for any of the passivation films, The results suggest that simple PECVD processes are effective for providing robust surface protection for InGaN/GaN LEDs.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.11
• /
• pp.862-866
• /
• 2012

Surface passivation of AlGaN/GaN heterojunction structure was examined through the thermal oxidation of evaporated Al. The Al-oxide passivation increased channel conductance of two dimensional electron gas (2DEG) on the AlGaN/GaN interface. The sheet resistance of 463 ohm/${\Box}$ for 2DEG channel before $Al_2O_3$ passivation was decreased to 417 ohm/${\Box}$ after passivation. The oxidation of Al induces tensile stress to the AlGaN/GaN structure and the stress seemed to enhance the sheet carrier density of the 2DEG channel. In addition, the $Al_2O_3$ films formed by thermal oxidation of Al suppressed thermal deterioration by the high temperature annealing.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.420-423
• /
• 2008

The characteristics of $Al_2O_3/Ag/Al_2O_3$ multilayer passivaton prepared by twin target sputtering (TTS) system for organic light emitting diodes. The $Al_2O_3/Ag/Al_2O_3$ multilayer thin film passivation on a PET substrate had a high transmittance of 86.44 % and low water vapor transmission rate (WVTR) of $0.011\;g/m^2$-day due to the surface plasmon resonance (SPR) effect of Ag interlayer and effective multilayer structure for preventing the intrusion of water vapor. Using synchrotron x-ray scattering and field emission scanning electron microscope (FESEM) examinations, we investigated the growth behavior of Ag layer on the $Al_2O_3$ layer to explain the SPR effect of the Ag layer. This indicates that an $Al_2O_3/Ag/Al_2O_3$ multilayer passivation is a promising thin film passivation scheme for organic based flexible optoelectronics.