• 한국표면공학회지
• /
• 제43권1호
• /
• pp.12-16
• /
• 2010

The morphology of the passivated surface of stainless steel (SS) was quantitatively characterized based on fractal geometry. In particular, the surface irregularities of the passivated 304 and 439 SSs were comparatively analyzed in terms of their self-similar fractal dimensions. The passivated surface of 439 SS in an acid-based electrolyte proved to have a higher fractal dimension, as compared to that of 304 SS, esp. at a scale of several tens of nanometers, strongly indicating the higher irregularity of the passivated surface. It is anticipated that the fractal approach suggested herein might be effectively utilized to analyze the irregularity of the steel surface and/or the compactness of the oxide film.

• 한국측량학회지
• /
• 제38권5호
• /
• pp.477-486
• /
• 2020

Drone has been widely used for many applications ranging from amateur and leisure to professionals to get fast and accurate 3-D information of the surface of the interest. Most of commercial softwares developed for this purpose are performing automatic matching based on SIFT (Scale Invariant Feature Transform) or SURF (Speeded-Up Robust Features) using nadir-looking stereo image sets. Since, there are some situations where not only nadir and nadir-looking matching, but also nadir and oblique-looking matching is needed, the existing software for the latter case could not get good results. In this study, a matching experiment was performed to utilize images with differences in geometry. Nadir and oblique-looking images were acquired through drone for a total of 2 times. SIFT, SURF, which are feature point-based, and IMAS (Image Matching by Affine Simulation) matching techniques based on affine transformation were applied. The experiment was classified according to the identity of the geometry, and the presence or absence of a building was considered. Images with the same geometry could be matched through three matching techniques. However, for image sets with different geometry, only the IMAS method was successful with and without building areas. It was found that when performing matching for use of images with different geometry, the affine transformation-based matching technique should be applied.

• 한국항공우주학회지
• /
• 제40권4호
• /
• pp.336-345
• /
• 2012

균열성장 수명에는 구조 형상의 복잡함, 작용하중의 변동, 재료물성 분포 등의 영향으로 불확실성이 포함된다. 따라서 이러한 불확실 인자들에 대해 계산된 수명의 강건성을 확보하기 위해서는 신뢰성 평가가 요구된다. 하지만 형상이 복잡한 터빈 휠의 경우 균열성장 수명 계산의 주요 변수인 응력확대계수의 표현식을 알기 힘들며, 이를 유한요소해석으로 계산하므로 수명 계산 및 신뢰성 평가에 많은 시간이 요구된다. 따라서 본 연구에서는 균열성장 수명의 반응표면을 사용함으로써 신뢰성 평가의 효율성을 높일 수 있음을 고찰하였다. 이를 위해 형상이 복잡한 터빈 휠을 모델로 유한요소해석으로 생성된 응력확대계수 데이터를 회귀분석하여 근사모델을 생성한 후 응력확대계수의 회귀계수, Paris 계수, 초기균열길이에 대한 균열성장 수명의 반응표면을 생성하여 신뢰성해석에 사용하였다. 신뢰성해석은 몬테카를로 시뮬레이션으로 수행하였으며, 연구결과 반응표면의 사용이 신뢰성 평가 시 필요한 균열성장 수명의 계산량을 효과적으로 줄일 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.400-400
• /
• 2009

In a wide variety of high-voltage applications surface flashover plays major role in the system's performance and yet has not been studied in great detail for atmospheric conditions with modem diagnostic tools. surface flashover for both direct current and pulsed voltages in considered. within the setup, parameters such as geometry, material characteristics of the applied voltage can be altered. This paper review surface flashover of insulator, primarily in atmosphere. It discusses theories and models relating to surface flashover and experimental results. surface flashover of insulators in atmosphere generally is initiated by the emission of electrons from the cathode triple junction point (the region where the electrode, insulator, air). the electrode material was copper, and a AC voltage was applied between the electrodes. these results were compared with the surface flashover characteristic of epoxy.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1145-1150
• /
• 2005

The aim of this paper is to investigate the effect of surface texturing on metal surface and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 is recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.

• 한국정밀공학회지
• /
• 제16권12호
• /
• pp.143-151
• /
• 1999

The shape of surface micro-crack is very irregular due to nonhomogeneous microstructure but is very important in respect to qualitative estimation of fatigue life. Fractal geomety can quantify the shape of surface mciro-crack. Fractal dimension is measured for surface micro-cracks with coast line and box counting method and estimates cycle ration in Al 2024-T3. The average fractal dimension $D_{favg}$ of surface micro-cracks has 3-parameter weibull distribution and location parameter is nearly constant but shape parameter decreases as cycle ration increases. The fractal dimension by coast line method is measured for individual surface micro-crack but the fractal dimension by box countin method is measured for all the surface micro-cracks under sampling area. Therefore, This paper shows fractal dimension $D_{fb}$ can predict cycle ratio $N/N_f$ more convenient than fractal dimension $D_{favg}$.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.872-879
• /
• 2010

High rock-fill embankment is relatively flexible, which makes crest of embankment subject to excessive amplification in displacement due to earthquake loading. To overcome problems related with site response in high embankment, it is essential to evaluate shear-wave velocity profile of the embankment with improved accuracy and reliability. In this aspect, an experimental research was performed to answer how to perform surface-wave tests and to analyze measurements at an embankment site with a sloping ground surface. Unlike flat ground surface, sloping ground may hamper and slow down propagation of surface waves due to multiple reflections and refractions in embankment. To figure out this reasoning for the effect of multiple reflections and refractions due to sloping surface, surface wave tests were performed at a reservoir embankment of Chung-Song in North KyeongSang Province. Parameters involved in surface wave tests at non-flat surface, including source directionality, geometry-related constraint and frequency components in source function, were investigated using field measurements.

• 한국CDE학회논문집
• /
• 제3권4호
• /
• pp.293-303
• /
• 1998

The objective of this study is to develop a PC level freeform surface modeling system which explicitly represents information of part geometry. Surface modeler uses nonuniform rational B-spline (NURBS) function with nonuniform knot vector for the flexible modeling work. The results of this study are as follows. 1) By implementation surface modeler through applying representation scheme proposed to represent free-form surface explicity, the technical foundation to develop free-from surface modeling system using parametric method. 2) Besides the role to model geometric shape of a surface, geometric modeler is developed to model arbitrary geometric shape. By doing this, the availability of the modeling system is improved. Geometric modeler can be utilized application fields such as collision test of tool and fixture, and tool path generation for NC machine tool.

• 한국정밀공학회지
• /
• 제21권9호
• /
• pp.196-203
• /
• 2004

SL(Stereolithography) part is made by piling up thin layers which causes the stair stepping effect at the surface of SL parts. The effect brings about excessive surface roughness and cuts down the merits of using SL part. Hence, additional post-machining finishing such as traditional grinding is required. But the traditional post-machining is detrimental to part geometry and time consuming. In this study, therefore, a paraffin coating and grinding post-machining is newly proposed to improve the surface quality of SL fart. The paraffin which has suitable properties for the proposed post-machining is coated all over the part surface. By grinding the only over-coated paraffin based on boundary of the SL part surface, the surface roughness can be improved without any damage on the part. Also, it is verified that SL part finished by the proposed post-machining process can be applied for rapid tooling as pattern through manufacturing silicon rubber molding and casting test.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.248-253
• /
• 1997

The ideal surface roughness is obtained by tool geometry and feed rate in face milling. however actual surface roughness is affected by various factors such as cutting conditions. vibration and used tool. To improve the quality and productivity of the machining parts, lots of research on the evaluation of tool life and control of surface roughness has been required. Therefore, the width of flank wear, cutting force, and surface roughness are monitored to analyse the characteristics of surface roughness. This experimental investigation is mainly focused on the characteristics of surface roughness in multi-insert milling using TiN coated tool.