• 조명전기설비학회논문지
• /
• 제20권4호
• /
• pp.37-42
• /
• 2006

본 논문에서는$CO_2$를 발생시키지 않고 물로부터 직접 수소를 제조하기 위하여 비열플라즈마를 이용하였다. 다중침-평판형(Multineedle-plate electrode geometry reacto: MPER)과 단일침-평판형(Needle-plate electrode geometry reactor: NPER) 두종류의 수소제조 반응기를 설계 제작하여 수소 발생에 미치는 영향에 대하여 실험하였다. 수소발생을 높이기 위해서는 강한 아크성 스트리머 방전 발생과 효과적인 수표면 방전을 위한 수표면 조건을 고려해야만 된다.

• 한국콘텐츠학회:학술대회논문집
• /
• 한국콘텐츠학회 2006년도 춘계 종합학술대회 논문집
• /
• pp.351-355
• /
• 2006

본 연구의 목적은 모든 하천에서 표면유속만을 이용하여 유량측정을 용이하게 할 수 있는 효과적이고 유용한 측정방법을 개발하는데 있다. 본 연구로 다음과 같은 중요한 결과를 얻었다. 1) 자연하천은 엔트로피 M값에 대응하여 평형상태를 유지하는 경향이 있으며, 2) 표면유속을 이용하여 산정된 계산치와 실측을 비교한 결과 상당히 좋은 일치를 보여주었으며, 3) 하천단면에서 최대유속이 발생하는 지점에서의 표면유속을 이용하여 유량을 산정하는 공식을 개발하였으며, 실측치와 비교한 결과 그 적용성을 확인하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.503-506
• /
• 2004

In this paper we investigated the changes of surface hydrophobic characteristics on silicone rubbers by corona discharge treatment and also investigated the distribution and the behavior of low molecular weight(LMW) silicone fluid which was extracted by solvent-extraction with gel permeation chromatography(GPC). It was shown that contact angle was $110.5^{\circ}$ on initial sample but contact angle was approximately decreased to $10^{\circ}$ after 45 minutes. However the surface hydrophobic characteristic on silicone rubbers which were removed from corona discharge was recovered within 5 hours. It was shown that corona discharge insured the increase of diffusible LMW chains, which could lead to recover the surface hydrophobicity. The surface hydrophobic characteristics on silicone rubbers and the recovery mechanism based on our results were discussed.

• 소성∙가공
• /
• 제28권5호
• /
• pp.239-246
• /
• 2019

Various surface texturing techniques have been studied because of the effective applicability of micro or nano scale surface patterns. Particularly, the most promising types of patterns include the hierarchical patterns, which consists of micro/nano structures. Different processes such as MEMS, laser machining, micro cutting and micro grinding have been applied in the production of hierarchical patterns on various material surfaces. This study demonstrates the process of hot imprinting to induce the hierarchical patterns on the Al alloy surfaces. Wire electrical discharge machining (WEDM) process was used to imprint molds with micro scale sinusoidal pattern. In addition, the sinusoidal pattern with rough surface morphology was obtained as a result of the discharge craters. Consequently, the hierarchical patterns consisting of the sinusoidal pattern and the discharge craters were prepared on the imprinting mold surface. Hot imprinting process for the Al plates was conducted on the prepared mold, and the replication performance was analyzed. As a result, it was confirmed that the hierarchical patterns of the mold were effectively duplicated on the surface of Al plate.

• 한국환경과학회지
• /
• 제13권9호
• /
• pp.759-765
• /
• 2004

HEC-RAS model is used for estimation of rating-curve of Musung in Wi stream. Discharge is computed from stage estimated by HEC-RAS model, is compared with the discharge of water surface slope method. The relative deviation of observed and computed discharge is 5.37%, and shows as a good results. A rating-curve by HEC-RAS model shows better results than by water surface slope method.

• Journal of Electrical Engineering and Technology
• /
• 제10권2호
• /
• pp.603-609
• /
• 2015

Dry air is an excellent alternative to $SF_6$ gas and is used as an insulation gas in Eco-friendly Gas Insulated Switchgears (EGISs), which has gained popularity in industry. Solid insulators in EGIS play an important role in electrical insulation. On the other hand, surface discharge can occur easily when solid insulators are used. This paper explored the surface discharge characteristics on the structure of three-layered laminated solid insulators to elevate the flashover voltage. A laminated solid insulator was inserted after the quasi-uniform electric field was formed in the test chamber. Dry air was then injected to set the internal pressure to 1 ~ 6 atm, and the AC voltage was applied. When identical solid insulators were stacked, the surface discharge characteristics were similar to those of a single solid insulator. On the other hand, the flashover voltage rose when the middle part was thicker and had lower permittivity than the top and bottom parts in the laminated solid insulator. Based on experimental results, when stacking a solid insulator in three layers, the middle part of the solid insulator should be at least four times as thick as the top and bottom parts and have lower permittivity than the others. In addition, the flashover voltage increased with increasing gas pressure on the surface of the laminated solid insulator due to the gas effect. This study may allow insulation design engineers to have useful information when using dry air for the insulation gas where the surface discharge can occur.

• 상하수도학회지
• /
• 제25권5호
• /
• pp.627-634
• /
• 2011

In the present study, the flow behaviors of square jets surface discharged and submerged discharged into shallow water were each simulated using computational fluid dynamics, and the results were compared. As for the verification of the models, the results of the hydraulic experiment conducted by Sankar, et al. (2009) were used. According to the results of the verification, the present application of computational fluid dynamics to the flow analysis of square jets discharged into shallow water was valid. As for the wall jet, which is one form of submerged discharges, at the bottom wall boundary, the peak velocity of the jet rapidly moved from the center of the jet to the bottom wall boundary due to the restriction of jet entrainment and the no-slip condition of the bottom wall boundary, and, as for the surface discharge, because jet entrainment is limited on the free water surface, the peak velocity of the jet moved from the center of the jet to the free water surface. This is because jet entrainment is restricted at the bottom wall boundary and the surface so that the momentum of the central core of the jet is preserved for considerable time at the bottom wall boundary and the surface. In addition, due to the effect of the bottom wall boundary and the free water surface, the jet discharged into shallow water had a smaller velocity diminution rate near the discharge outlet than did the free jet; at a location where it was so distant from the discharge outlet that the vertical profile of the velocity was nearly equal (b/x =20~30), moreover, it had a far smaller velocity diminution rate than did the free jet due to the effect of the finite depth.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2002년도 학술대회논문집
• /
• pp.251-255
• /
• 2002

This paper describes the analysis of UHF signals taking place at partial discharges due to defects in GIS. To imitate the defects, two kinds of electrode were employed. One is to generate the PD due to corona discharge, and the other surface discharge. As a result, the magnitude of the UHF signals acquired from the discharges increased with the applied voltage. However, each frequency distribution trend at corona discharges and surface discharge was similar even though the applied voltage increased. Frequency distribution between corona discharge and surface discharge was clearly distinguish.

• 한국환경과학회지
• /
• 제26권9호
• /
• pp.999-1011
• /
• 2017

In this study, the Chiu-2D velocity-flow rate distribution based on theoretical background of the entropy probability method was applied to actual ADCP measurement data of Gangjung Stream in Jeju from July 2011 to June 2015 to predict the parameter that take part in velocity distribution of the stream. In addition, surface velocity measured by SIV (Surface Image Velocimeter) was applied to the predicted parameter to calculate discharge. Calculated discharge was compared with observed discharge of ADCP observed during the same time to analyze propriety and applicability of depth of water velocity average conversion factor. To check applicability of the predicted stream parameter, surface velocity and discharge were calculated using SIV and compared with velocity and flow based on ADCP. Discharge calculated by applying velocity factor of SIV to the Chiu-2D velocity-flow rate distribution and discharge based on depth of water velocity average conversion factor of 0.85 were $0.7171m^3/sec$ and $0.5758m^3/sec$, respectively. Their error rates compared to average ADCP discharge of $0.6664m^3/sec$ were respectively 7.63% and 13.64%. Discharge based on the Chiu-2D velocity-flow distribution showed lower error rate compared to discharge based on depth of water velocity average conversion factor of 0.85.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2320-2322
• /
• 1999

This paper was studied on the surface discharge characteristics and tracking phenomena on the solid insulator in liquid nitrogen ($LN_2$) at atmospheric pressure. In order to investigate the bubbles which have much influence on electric surface discharge in liquid nitrogen, Knife type electrode and plane electrode were arranged in different modes(Mode A, Mode B, and Mode C) and investigated for surface discharge and tracking phenomena. In Mode A, by the movement of bubbles tracking damage was formed under the electrodes. The tracking pattern in Mode B was formed along the electrode axis.