• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.89-90
• /
• 2022

Arc metal spraying is a widely used method for improving the performance of construction structures such as corrosion resistance and electromagnetic wave shielding. However, when arc metal spraying is applied to a concrete structure, adhesion performance may deteriorate. Therefore, the effect of each surface treatment method on the physical properties between the arc metal spray coating and concrete was reviewed by evaluating the deposition efficiency and adhesion performance according to the arc metal spray surface treatment method (surface reinforcing agent, roughening agent, and sealing agent). As a result, it is suggested as an optimal surface treatment condition to induce non-interface failure by using a roughening agent and to improve the properties of concrete and metal coatings by applying a surface reinforcing agent and sealing agent.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.4
• /
• pp.915-924
• /
• 1996

The purpose of this paper is to investigate the surface roughness of glass ionomer cement during initial setting time followed by applying surface coating agent. No other finishing or polishing procedure is done and each surface coating agents (varnish, adhesive, gloss, sealant) are used after filling of glass ionomer cement. Surface roughness indices(Ra) are measured and surface contours are obtained electronically by Surfcorder SEF-30D(Kosaka laboratory Ltd., Japan). The results are as follows: 1. During initial setting time, surface roughness increases slightly regardless of surface coating agents. But it is statistically insignificant. (p>0.05) 2. Among surface coating agents used, Ra indices of group using varnish are high significantly compared to other groups regardless of elapsed time.(p<0.05) Among the groups which has used other surface coating agents except for the varnish group, similar Ra index all over the experiment is obtained, when compared to control group (no agent). 3. If no surface treatment is performed, tri-cure glass ionomer cement (Vitremer) has higher Ra Index than light cure glass ionomer cement (Fuji II LC) (t<0.05). But there is no difference between two groups in Ra index if any kinds of agents are applied except for sealant. (t>0.05)

• Journal of Conservation Science
• /
• v.27 no.4
• /
• pp.415-420
• /
• 2011

Urethane coating agent was made up in order to prevent corrosion on metal relics. This urethane coating agent was designed to solve problems linked to gloss and discoloration caused by existing acrylic coating agent which is mainly applied to metal relics. For the purpose, the urethane coating agent was made up which has lower gloss and slight color change. This coating agent formed thinner coating layer with excellent adhesion compared to the existing agent and has outstanding resistance to the surface oxidization of metal relics and water repellent on the surface. In addition, the agent is considered a stable coating agent replacing current acrylic coating agent with showing easy dissolution in organic solvents such as acetone, toluene and xylene with excellent result in reversible reaction.

• Magazine of the Korea Concrete Institute
• /
• v.2 no.4
• /
• pp.61-68
• /
• 1990

This experimental study is aimed to investigate the coating method of scoria lightweight aggregate for reo duction of water absorption and the physical dynamic characteristics of coated-scoria jightweight aggregate con¬crete. The coating methods are as follows: I) Non-coating method. II) Coating method of only cement paste. rn) Coating mehtod of surface-coating agent after coating by cement paste. IV) Coating method of only surfaee-coating agent. V) Coating method of cement pasted after coating by surface-coating agent. The summerized conclusion are as fallows ; 1) Specific gravity and the rate of water absorption were lowest when aggregate was covered by only surface-coating agent, especially, rate of absorption was about 10% of non-coating aggregate. 2) Coated-aggregate were about 0.87~0.97t/m3 and lightweight concrete made of coated-aggre¬gates were 1.80~ 1.94 t/m3 in unit weight. 3) Compressive strength of the lightweight concrete made of cement pasted-coating aggregate was about 200~215kg/crrl. 4) The higher the rate of water absorption of coarse aggregate, the higher the rate of deterioration of compressive strength.

• Journal of dental hygiene science
• /
• v.9 no.2
• /
• pp.153-160
• /
• 2009

The purposed of this study was to investigate the effect of Gold bonding agent as intermediate layer between metal substrate and ceramic coating. Gold bonding agent used to seal off any surface porosity, to mask the greyish color of the metal, and to provide an underlying bright golden hue to the ceramic coverage. The adhesion between metal substrate and ceramic is related to diffusion of oxygen during ceramic firing. The oxide layer produced on non-precious alloy anti titanium was considered to have a potentially adverse effect on metal-ceramic bonding. The oxidation characteristics of titanium and non-precious alloys are the main problem. Every group were divided into test and control groups. Control groups are carried out process of degassing for product oxide layer. Au coating was applied on each Ni-Cr, Co-Cr alloys and cp-Ti specimens with difference surface condition or degassing. Specimens surfaces and cutting plane was characterized by SEM/EDS. Results suggested that Au coating is effective barriers to protect metal oxidation during ceramic firing.

• Journal of Industrial and Engineering Chemistry
• /
• v.68
• /
• pp.387-392
• /
• 2018

Various technical approaches and concepts have been proposed to develop conductive super-hydrophobic (SH) surfaces. However, most of these approaches are not usable in practical applications because of insufficient adhesion and cost issues. Additionally, durability and uniformity issues are still in need of improvement. The goal of this research is to produce a large-area conductive SH surface with improved adhesion performance and uniformity. To this end, carbon nanotubes (CNT) with a high aspect ratio and elastomeric polymer were utilized as a conductive filler and matrix, respectively, to form a coating layer. Additionally, nanoscale silica particles were utilized for stable implementation of the conductive SH surface. To improve the adhesion properties between the SH coating layer and substrate, pretreatment of the substrate was conducted by utilizing both wet and dry etching processes to create specific organic functional groups on the substrate. Following pretreatment of the surface, a zirco-aluminate coupling agent was utilized to enhance adhesion properties between the substrate and the SH coating layer. Raman spectroscopy revealed that adhesion was greatly improved by the formation of a chemical bond between the substrate and the SH coating layer at an optimal coupling agent concentration. The developed conductive SH coating attained a high electromagnetic interference (EMI) shielding effectiveness, which is advantageous in self-cleaning EMI shielding applications.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.2
• /
• pp.56-61
• /
• 2015

In this study, the wear performance of manganese phosphate coating on SM45C with addition agent of Tartaric acid and Citric acid were investigated. The Surface morphology of manganese phosphate coating was examined by Scanning Electron Microscope (SEM) and Energy Dispersive X-ray spectroscopy (EDS). It is found that Mn, P, Fe, O and C. The crystal structure and thee composition was analysis and determined by using XRD. The XRD results indicated that manganese phosphate coatings are mainly composed of $(Mn,Fe)_5H_2(PO_4)_44H_2O$ and consists of a lot of close packed lump crystalline. Based on the time dependence of morphology and the weight of manganese phosphate coating, it shows that the phosphating process mainly includes three stages: corrosion of the substrate, creation and growth of phosphate crystal nucleus and thickening of manganese phosphate coating. The wear tests were performed in a ball on disc apparatus as per ASTM G-99 Standard. It was showed that the initial wear was quite high followed by low sludge.

• Corrosion Science and Technology
• /
• v.11 no.1
• /
• pp.15-19
• /
• 2012

Both electrogalvanized and hot-dip galvanized steel sheets have been finally produced via organic-inorganic surface coating process on the zinc surface to enhance corrosion resistance and afford additional functional properties. Recently, POSCO has been developed a variety of chromate-free coated steels that are widely used in household, construction and automotive applications. New organic-inorganic hybrid coating solutions as chromate alternatives are comprised of surface modified silicate with silane coupling agent and inorganic corrosion inhibitors as an aqueous formulation. In this paper we have prepared new type of hybrid coatings and evaluated quality performances such as corrosion resistance, spot weldability, thermal tolerance, and paint adhesion property etc. The electrogalvanized steels with these coating solutions exhibit good anti-corrosion property compared to those of chromate coated steels. Detailed components composition of coating solutions and experimental results suggest that strong binding between organic-inorganic hybrid coating layer and zinc surface plays a key role in the advanced quality performances.

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.1
• /
• pp.21-28
• /
• 2014

The purpose of this study is to investigate the mechanical properties and carbonation resistance of concretes using lightweight aggregate coated surface finishing materials. To evaluate the mechanical properties and carbonation resistance of concrete, slump, air amount, air-dried unit volume weight, compressive strength, and carbonation depth are tested. In terms of the unit volume weight of concrete, air-dried unit volume weight of concrete using coating lightweight aggregate was measured as $1,739{\sim}1,806kg/m^3$. When using coating aggregate, compressive strength of concrete at 28 days was measured as much as 82.7~95.9% of the compressive strength using non-coating aggregate. It is found that compressive strength tends to decrease with coating lightweight aggregate. However, all concretes using coating lightweight aggregate except O-LWAC satisfied the criteria for 28-day compressive strength suggested in KS. The measurement of carbonation depth when the water-repellent agent was used found that carbonation depth was reduced by as much as 2.6~6.1%. On the other hand, when using polymer waterproof agent, carbonation depth was reduced by as much as 8.6~12.0%. Consequently, to improve carbonation resistance, polymer waterproof agent was more effective than water-repellent agent. In particular, epoxy showed the most outstanding performance.

• Elastomers and Composites
• /
• v.50 no.2
• /
• pp.98-102
• /
• 2015

A series of polyurethane-acrylate hybrids were synthesized by 2-step emulsion polymerization of a variety of acrylate monomers such as 2-hydroxy ethyl methacrylate (HEMA), methyl methacrylate (MMA). Experiment was performed to improve stability and emulsibility of surface treatment agent, and it was found that the polyurethane-acrylate hybrids having an optimum composition (MMA : 20%, LA(EO)3-S : 3% and TDA-7 : 5%) was shown to be quite surface active in the solid contents. These results suggests that the optimal polyurethane-acrylate hybrids in this study have high potential as top coating agent, which may have high gloss and excellent properties.