• 한국정밀공학회지
• /
• 제4권4호
• /
• pp.56-71
• /
• 1987

Determination of navigation variables (latitude, longitude, and altitude) near the earth's surface is termed 'Terrestrial Navigation'. The quantities that are measured inertially are the total acceleration (or the integral fo this acceleration over a fixed time interval) and the total angular rate (or the integral of this angular rate over the same time interval). These measurements when suitably compensated can be manipulated to yield the navigation variables. Hence, it is essential that the initial values of position, orientation and velocity are accurately set up during the initial alignment process. Initial alignment of gimballed inertial navigation system ( GINS) is accomplished by gyrocompassing techniques. These cannot be used, in the case of strapdown inertial navigation system(SDINS), where the inertial instruments are directly strapped down to a vehicle frame. The basic objective of this paper is the development of digital method for the determination of the initial axes erection of a SDINS from vibration and sway currupted data on the launch pad.

• 공업화학
• /
• 제9권2호
• /
• pp.300-305
• /
• 1998

세 종류의 모노머로 구성된 삼모노머중합의 동력학을 입자성장이 끝난 interval II 동안 pseudo-homopolymerization (PHP) 방법에 의하여 연구하였다. 삼모노머중합의 Smith-Ewart 확장식과 순간중합조성식을 단일유화중합의 해당식과 유사하게 나타낼 수 있었다. 입자당 평균라디칼수와 순간중합조성을 라텍스입자내의 모노머조성을 변화시킴으로써 입자당 자유라디칼수가 한 개 이하인 계에서 예측하였다. 모델계산의 예로서 Styrene-Methyl methacrylate-Acrylonitrile(SMA)계의 속도상수들을 사용하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1593-1595
• /
• 2000

We present a new procedure to evaluate the degradation in a lCr-lMo-0.25V steel. The method is based on the existence of the peak of reversible permeability in the differential magnetization around the coercive field strength. The apparatus is based on the detection of the voltage induced in a surface type coil using a lock-in amplifier tuned to a frequency to the exciting one. Results obtained the reversible permeability and Vickers hardness on the annealed samples show the peak interval of reversible permeability and Vickers hardness decreased as ageing time increased. The correlation between Vickers hardness and the peak interval of reversible permeability could well be evaluated non destructively.

• 한국유기농업학회지
• /
• 제19권spc호
• /
• pp.259-262
• /
• 2011

In organic Chinese cabbage fields, Commercial Bacillus thuringiensis products are used widely against diamond back moth, Plutella xylostella. We conducted the study to determine the effective spray-interval of commercialized B. thuringiensis against diamond back moth on Chinese cabbages. Chinese cabbage leaves were collected 0, 1, 2, 3, 6, 10days after treatment in first trial and 0, 2, 4, 7, 9, 11days after treatment. We compared the insecticidal property of sprayed B. thuringiensis and the density of it on surface of Chinese cabbages using collected leaves. The insecticidal property maintained high until nine days after commercial B. thuringiensis products sprayed.

• 대한기계학회논문집A
• /
• 제24권3호
• /
• pp.661-666
• /
• 2000

Optimization of the elastic joint of train is performed according to the minimization of ten responses which represent driving safety and ride comfort of train and analyzed by using the each response se surface model from stochastic design of experiments. After the each response surface model is constructed, the main effect and sensitivity analyses are successfully performed by 2nd order approximated regression model as described in this paper. We can get the optimal solutions using by nonlinear programming method such as simplex or interval optimization algorithms. The response surface models and the optimization algorithms are used together to obtain the optimal design of the elastic joint of train. the ten 2nd order polynomial response surface models of the three translational stiffness of the elastic joint (design factors) are constructed by using CCD(Central Composite Design) and the multi-objective optimization is also performed by applying min-max and distance minimization techniques of relative target deviation.

• 한국가시화정보학회지
• /
• 제5권2호
• /
• pp.39-47
• /
• 2007

This paper describes an experimental study on the droplet formation and the subsequent motion in a microchannel having a cross junction. While one kind of liquid (pure water or water-surfactant mixture) is drawn into a horizontal inlet channel, the other kind (oil) is introduced through two vertical inlet channels. Due to the effect of surface tension on the interface between the two fluids, the droplets of the first fluid are formed near the cross junction. In this study, we have found that the droplet formation is affected even by slight difference in the surface tension. When the surface tension between two fluids is decreased, the droplet size is decreased in order to keep the equilibration between the pressure and the surface tension. In addition, the time interval between each of the droplet formations is decreased and the distance between droplets is also decreased when the surface tension is decreased.

• Environmental Engineering Research
• /
• 제21권2호
• /
• pp.196-202
• /
• 2016

Membrane bioreactor (MBR) technology has previously been used by water industry to treat high salinity wastewater. In this study, an anoxic-oxic biofilm-membrane bioreactor (AOB-MBR) system has been developed to treat mustard tuber wastewater of 10% salinity (calculated as NaCl). To figure out the effects of operating conditions of the AOB-MBR on membrane fouling rate ($K_V$), response surface methodology was used to evaluate the interaction effect of the three key operational parameters, namely time interval for pump (t), aeration intensity ($U_{Gr}$) and transmembrane pressure (TMP). The optimal condition for lowest membrane fouling rate ($K_V$) was obtained: time interval was 4.0 min, aeration intensity was $14.6 m^3/(m^2{\cdot}h)$ and transmembrane pressure was 19.0 kPa. And under this condition, the treatment efficiency with different influent loads, i.e. 1.0, 1.9 and $3.3kgCODm^{-3}d^{-1}$ was researched. When the reactor influent load was less than $1.9kgCODm^{-3}d^{-1}$, the effluent could meet the third discharge standard of "Integrated Wastewater Discharge Standard". This study suggests that the model fitted by response surface methodology can predict accurately membrane fouling rate within the specified design space. And it is feasible to apply the AOB-MBR in the pickled mustard tuber factory, achieving satisfying effluent quality.

• 한국해안·해양공학회논문집
• /
• 제35권2호
• /
• pp.41-48
• /
• 2023

본 연구에서는 바닥의 움직임에 따른 파랑의 생성 및 변화를 모의할 수 있는 간단한 선형 수치해석 기법을 소개한다. 연속방정식과 선형의 동역학적 및 운동학적 자유수면 경계조건, 선형의 운동학적 바닥 경계조건을 공간에 대해 푸리에 변환한 후 파수 영역에서 수치해석을 수행하며, 결과는 푸리에 역변환을 통해 공간영역에서 표현된다. 파수 영역에서 동역학적 자유수면 경계조건과 운동학적 자유수면 경계조건이 수치적으로 계산되며, 이 때 평균수면 (z = 0)에서의 속도포텐셜은 연속방정식과 운동학적 바닥 경계조건을 만족한다. 삼각형 및 사각형 형상의 바닥이 주기적으로 움직이는 경우의 파랑 생성 및 전파에 대해 검토하였다. 간편 수치해석 기법을 이용한 결과는 기존의 선형 해석해와 비교하였으며, 거의 일치하는 결과를 보였다. 계산 시간간격(Δt)과 계산 파수간격(Δk)에 따른 수치해석 결과의 안정성에 대해서도 검토하였다. 검토 결과 Δt ≤T(주기)/1000, Δk ≤ π/100 일 때 수치해석에 의한 결과가 적절하게 도출되는 것으로 나타났다.

• 한국공작기계학회논문집
• /
• 제14권2호
• /
• pp.14-20
• /
• 2005

This paper describes a dwell time calculation algorithm for polishing tool path generation in the small toot polishing process of the axis-symmetrical lens. Generally dwell time control in the polishing machines means that small polishing tool stays for a dwell time at the specific surface position to get the expected polishing depth. Polishing depth distribution on an aspherical lens surface consists of the superposition of the local polishing depth at the each dwell position. Therefore, tool path generation needs each dwell time together with tool positioning data during the polishing tool movements on the aspherical lens surface. The linear algebraic equation of removal depth removal matrix and dwell time is formulated. Parametric effects such as the dwell d interval are simulated to validate the dwell time calculation algorithm.

• 오토저널
• /
• 제15권3호
• /
• pp.120-125
• /
• 1993

The surface roughness of workpiece is reduced during spark-out. The reduction of roughness is a benefit of spark-out, but spark-out lowers productivity. The characteristics of spark-out are different to those of plunge grinding to which feed is applied. This difference is due to overlapping cutting during spark-out. Effect of spark-out is in proportion to volume of grain wear. This phenomenon is due to different overlapping area. Dressing interval can be enlarged by spark-out, when volume of grain wear is large. In this study, the characteristic of spark-out was studied by spark-out obserbation in various grinding conditions. For this purpose thrust force, spark-out time and surface roughness of workpiece were experimentally investigated in various grinding conditions.