• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1353-1358
• /
• 2004

An experimental study of pool boiling behavior on micro-porous enhanced square heater surfaces immersed in PF5060 is performed. The effects of heater orientation, Subcooling and substrate distance on the pool boiling heat transfer performance for the double heaters were investigated under increasing heat-flux conditions. The boiling performance of micro-porous coated surface was better than that of plain surface. The double heaters with upper substrate of 0.2cm substrate interval have lower boiling performances compared with the results for the double heaters with that of 0.5cm and 1.0cm substrate interval and without the substrate. In comparison to upper heater and below heater with orientation, the upper heater has lower superheat temperature than the below heater due to the bubble sweeping.

• Journal of the Korean Society of Safety
• /
• v.14 no.3
• /
• pp.25-32
• /
• 1999

This study has been performed to investigate the stress distribution around defects that behave as stress concentrators. Besides, the effect of stress interaction effects on the initiation of primary cracks were also investigated by rotary bending fatigue tests which were performed with specimens drilled micro surface defects and the stress distribution was analyzed using Finite Element Method. In addition, the stress interaction effects around defects and cracks were investigated by comparing the results of experiments and F.E.M. The results obtained are summarized as follows ; 1) Area which slip and micro cracks initiated at micro surface defects is between the maximum shear stress points and this area is over than ${\pm}30^{\circ}$ from the maximum stress point along the defect edge. 2) The stress interaction effect for the small size defect is larger than that of large size defect when the interval between them is near 3) Interval which there is no shear stress interaction effect analyzed by F.E.M. is larger than that of experimental results.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.3
• /
• pp.77-82
• /
• 2014

In this study, we carried out the interrupted cutting of carbon steel for a machine structure (SM45C) with a CVD-coated tool and conducted an ANOVA test and a confidence interval analysis to find factors influence the surface roughness and to obtain a regression equation. We found that factor which mostly affects the surface roughness during interrupted cutting was the feed rate. The cutting speed and depth of the cut only had small effect on the surface roughness. From the result of a multi-regression analysis during an interrupted cutting experiment, we obtained regression equation. Its coefficient of determination was 0.918, indicating that the regression equation was predictable. Compared to continuous cutting, if the feed rate increases, the surface roughness will also increase during interrupted cutting.

• Proceedings of the KOSOMBE Conference
• /
• v.1989 no.05
• /
• pp.13-14
• /
• 1989

Prolongation in QT corrected interval (QTc), measured in surface ECG, has been shown in the majority af patients to be marker of bad prognosis in postmyocardial infarction patients (PMIP). Hence it would seem logical that dynamic QTc interval measurement can be a very usefull indicator to stratify prognosis in PMIP. We present a new algorithm for QT as well as for QTP (distance value from Q wave onset to T wave peak) intervals measurement in 24 hour ECG Holter tapes. Validation of the algorithm by hand measurement has been done on first beats of 18 Holter tapes, resulting in a magnitude of deviations between 10 and 15 ms. Application on 24 hour Holter ECG signal has also been done.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.1
• /
• pp.470-477
• /
• 2013

The aim of this study is to suggest a detection method of water surface location and its evaluation results of application for same vertical position in two successive images with time interval including both staff gauge and water surface. A specific rectangular inspection area is defined from the top of watermark and then the correlation coefficients for the inspection area of the same position of two images with short time interval is calculated. Accordingly, it is possible to identify differences between changing area and fixed area of pixel density by the water flow. The photographs taken in the laboratory were analyzed in order to validate the proposed technique. As the result of the experiment, it is identified that characteristic of correlation coefficients depends on the size of the inspection area. In the case that the inspection area is within the entire width of the watermark, water surface characteristic according to correlation coefficients is clearly noticeable. Thus, it is identified that the proposed technique can be utilized to search water surfaces. Besides, using corelation analysis of two images with time interval, it is identified that error range between 10 and 42cm was reduced in the level of 2.6cm or less in the contaminated photo of existing image stage gauge. Therefore, it is expected that the suggested method can be utilized to enhance image stage gauge performance improving the previous water surface detection method.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.5
• /
• pp.115-120
• /
• 1999

This research is a described result of experimental for the parameter's effecting the microhole machining by Nd-Yag laser, The parameters are energy, pulse interval time a kin of assisting gas and its pressure. The result reveals that parameter value of energy 0.08J, pulse 20Hz, interval time of 300 microseconds could be a good machining condition to make upper microhoel that is the diameter range of 50-70${\mu}{\textrm}{m}$. At tat time the assistant gas such air, $O_2$, Ar $N_2$, was appelied. Assistant gas of air makes heat affected zone enlarge due to burning of material surface. Also it makes microhole irregular and damageable. Because of refusion caused by chemical reaction with $Al_2O_3$ ceramic material . The $O_2$(99.9%) has good characteristics to get good drilling and smooth surface on pressure of 0.2kgf/$\textrm{cm}^2$ but it is expensive. Ar, $N_2$ make material crack and burnning and proved that to be unappropriate but, Ar was a better than $N_2$.

• The Journal of the Acoustical Society of Korea
• /
• v.29 no.7
• /
• pp.431-438
• /
• 2010

The radiation pattern of conformal transducers installed on a curved surface is likely to be complicated depending on the array pattern on the curved surface. In this research, the acoustic sources constituting a conformal transducer are arrayed in equi-angle, equi-interval, and geodesic dome forms, and the radiation pattern function of each of the array geometries has been derived, and therewith the radiation pattern has been analyzed for each array geometry. Based on the analysis result, we have determined the equi-interval array geometry that provides the widest beam width with the lowest side lobe level among the three array geometries. Results of the present work are expected to be utilized to the design of conformal transducer structures.

• Tunnel and Underground Space
• /
• v.12 no.4
• /
• pp.268-276
• /
• 2002

In this study, a 3D coordinate measurement system equipped with a laser displacement meter for digitizing rock joint surface was established and the digitized data were used to calculate several roughness parameters. The parameters used in this study were micro avenge inclination $angle(i_{ave})$, average slope of joint $asperity(SL_{ ave})$, root mean square of $i-angle(i_{rms})$, standard deviation of height(SDH), standard deviation of $i-angle(SD_i)$, roughness profile $index(R_P)$, and fractal dimension(D). The relationships between the roughness parameters based on the digitzation of the surface profile were analyzed. Since the measured value varied according to the degree of reflection and the variation of colors at the measuring point, rock joint surface was painted in white to minimize the influence of the surface conditions. The comparison of the measured values and roughness parameters before and after painting revealed the better consequence from measurement on the painted surfaces. Also, effect of measuring interval was studied. As measured interval was increased, roughness parameters were exponentially decreased. The incremental sequence of degree of decrease was $SDH\; i_{ave},\; i_{rms},\; SD_i,\;and\; R_ p-1$. As a result of comparison of parameters from pin-type measurement system and laser type measurement system, all value of parameters were higher when laser-type measurement system was used, except SDH.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.32 no.1
• /
• pp.42-49
• /
• 1996

The author examined the response of Armorclad rockfish, Sebastes hubbsi [MATSUBARA]to the surface attracting lamps (0.5W, 0.8W, 1W) line in the experimental water tank ($550L{\times}58W{\times}73H$cm). The attraction rate was investigated in accordance with the intervals of lighting and putting out hour (1,5 minute) when each of the attraction lamps was gradually switched off after they were switched on all at once. The results are as follows : 1. Total distribution rate of fish in the illuminated section was 61.6%(mean 12.3%) in case of 1 minute interval, and 41.0%(mean 8.2%) in case of 5 minutes interval. 2. Mean distribution rate of fish at the illuminated section : \circled1Distribution rate at interval of 1 minute were 12.7% in 0.8W, 12.4% in 0.5W and 11.9% in 1 W respectively. \circled2Distribution rate at interval of 5 minutes were 9.0% in 1W, 8.6% in 0.8W and 7.0% in 0.5W respectively. 3. Attraction rates of the last section showed a little increasing as illuminating time elapsed. A difference of attraction rates according to lighting source in 1 minute interval was bigger than that in 5 minute interval. 4. Attraction rate of fish in only last section switched on : \circled1Attraction rate at interval in case of 1 minute were 52.0% in 0.8W, 46.7% in 0.5%W and 45.3% in 1W respectively. \circled2Attraction rate at interval in case of 5 minutes were 32.0% in 1W, 24.0% in 0.8W and 14.7% in 0.5W respectively.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.28 no.3
• /
• pp.243-251
• /
• 1992

The author examined the response of File fish, Stephanolepis Cirrhifer (TEMMINCK et SCHLEGEL) to the surface attracting lamps(0.5W, 0.8W, 1W) line in the experimental water tank (550L$\times$58W$\times$73H cm). the attracting rate was investigated in accordance with the interval of lighting and putting out hour (1, 5 minute)when each of the attracting lamps was gradually switched off after they were switched on all at once. The results are as follows: 1. Total distribution rate of fish in the illuminated section was 96.9%(mean 19.4%) in case of 1 minute interval, and 98.4%(mean 19.7%) in case of 5 minutes interval. 2. Mean distribution rate of fish at the illuminated section: \circled1 Distribution rate at interval of 1 minute were 19.9% in 0.8W, 19.3% in 1W and 18.9% in 0.5W respectively. \circled2 Distribution rate at interval of 5 minutes were 19.8% in 1W, 19.8% in 0.8W, and 19.5% in 0.5W respectively. 3. Attracting rate of the last section showed increasing as illuminating time elapse without interval and lighting source. 4. Attracting rate of fish in only last section switched on: \circled1 Attracting rate at interval in case of 1 minute were 98.0% in 1W, 97.0% in 0.5W and 83.0% in 0.8W respectively. \circled2 Attracting rate at interval in case of 5 minutes were 99.3% in 1W, 97.3% in 0.5W and 93.3% in 0.8W respectively.