• 한국주조공학회지
• /
• 제39권1호
• /
• pp.7-13
• /
• 2019

Few studies of large blooms over 700 mm thick among those used for the forging of raw materials have been reported. The cooling rate difference between the surface and the center of a large bloom is large, and the degradation of the mechanical properties is likely in cases involving excessively coarse precipitates resulted from the slow cooling rate of a large bloom after casting. Therefore, a schematic investigation of the growth behaviors of precipitates while varying their locations in blooms is necessary. The dissolution behaviors of precipitates were investigated by simulating a reheating process during which the bloom is heated to a high temperature. The segregation behavior of the as-cast large bloom was also investigated. Reheating specimens were obtained after an isothermal heat treatment at $1150^{\circ}C$ with various holding times to simulate the reheating process, with the samples undergoing a subsequent water quenching step. The precipitates were extracted using an electrolytic extractor and a particle size analysis was conducted with the aid of SEM, EDS, and TEM. In the present work, Al oxide, MnS and Nb carbide were mainly observed.

• 한국의류산업학회지
• /
• 제21권3호
• /
• pp.363-369
• /
• 2019

This study developed electroconductive textiles by coating polypyrrole to PET nonwoven-based Polyvinyl Alcohol (PVA) nanoweb made by electrospinning and applying the developed electrotextiles as ECG Electrodes. To find the optimum coating conditions for high electrical conductivity, the ratios of 2.6-Naphthalenedisulfonic acid with Disodium Salt (NDS) vs Ammonium Persulfate (APS) as an oxidant and a doping agent in the solution were changed from 3:7 to 7:3; the immersion time of the specimen in the solution was 1 hour. PVA nanowebs coated with polypyrrole under various conditions were filmed with FE-SEM. FT-IR analysis was also performed to examine the presence of polypyrrole nanoparticles in the PVA nanoweb. The electrical resistance of the treated specimens were measured with a Multimeter. Consequently, the PVA Nano Web was undamaged even after heat treatment that allowed for coating. Uniform polypyrrole nanoparticles then formed on the surface of the PVA nanoweb after coating. The measured electrical resistance was shown to be at least $12K{\Omega}/{\Box }$ from a maximum of $3,456K{\Omega}/{\Box }$. The proper amount of NDS content had a positive effect on the conductivity improvement of electroconductive textiles; in addition, the highest electrical conductivity was achieved with a ratio of 3:7 between NDS and APS.

• Korean Chemical Engineering Research
• /
• 제57권5호
• /
• pp.672-678
• /
• 2019

리튬이차전지용 음극재로서 피치로 코팅된 천연흑연의 전기화학적 특성이 조사되었다. 천연흑연과 피치의 혼합물을 $1000^{\circ}C$에서 소성하여 음극재를 제조하였다. 다양한 연화점의 피치가 탄소전구체로 사용되었다. 제조된 음극재의 물리적 특성은 TGA, SEM, PSA 및 BET로 분석하였다. 피치의 연화점이 증가할수록 코팅 층의 두께가 증가하였고, 비표면적이 감소하였다. 초기 충 방전 효율, 사이클, 순환전압전류, 속도 특성 및 임피던스 테스트를 통해 전기화학적 성능을 조사하였다. 연화점 $250^{\circ}C$의 피치로 탄소 코팅된 천연흑연은 초기 방전용량 361 mAh/g과 쿨롱 효율 92.6%을 보였다. 또한 출력 특성(5 C/0.2 C)은 코팅되지 않은 천연흑연에 비해 1.6배 향상되었으며, 0.5 C로 진행된 사이클 테스트에서 50 사이클 후 90%의 용량 유지율을 나타내었다.

• 공업화학
• /
• 제22권2호
• /
• pp.185-189
• /
• 2011

본 연구에서는 화학적 공침법을 적용하여 가스상 이산화탄소 분해를 위한 나노크기의 M-페라이트(M=Co, Ni, Cu, Zn)를 제조하였다. 열중량 분석 결과, 시험제조한 모든 시료의 최고 무게 감소율은 $350^{\circ}C$ 미만에서 발생하였다. 소성온도가 증가할수록 결정형은 우수하여 표면촉매활성화를 기대할 수 있지만, 입자결정의 크기가 크고, 비표면적이 낮은 페라이트가 합성됨을 알 수 있었다. FT-IR 분석으로부터 $375{\sim}406cm^{-1}$의 범위에서 octahedral site에 착화물이 존재함을 확인 할 수 있었으며, 이는 페라이트 내 스피넬 구조가 형성되어 있음을 보여주는 것이라고 믿는다. 본 연구로부터 얻은 이산화탄소 분해반응을 위한 금속페라이트의 최적 열처리 온도는 $500^{\circ}C$인 것으로 나타났다.

• 대한금속재료학회지
• /
• 제46권4호
• /
• pp.189-198
• /
• 2008

The changes in microstructure and mechanical properties of AZ31 alloy subjected hot-rolling process were investigated. The AZ31 plates fabricated by horizontal continuous casting process were prepared and have hot-rolled from 30 mm to 1 mm in thickness under different processing conditions. At the rolling temperature of $400^{\circ}C$, little surface and side crack was observed up to 20% reduction rate. As total reduction and reduction rate increase to more than 75% and 20% pass, respectively, Grains were more uniformly refined through overall thickness, and particularly lots of shear bands were appeared to be inclined at less than $20^{\circ}C$ along the rolling direction. Average grain size of less than $5{\mu}m$ and tensile properties of YS ${\geq}$ 250 MPa, UTS ${\geq}$ 300 MPa and El. ${\geq}$ 13% were acquired for hot-rolled AZ31 sheets without post-heat treatment. Maximum intensity of (0002) pole figure was decreased with an increase in reduction rate, indicating the improvement of texture by means of high reduction rate.

• 한국군사과학기술학회지
• /
• 제25권6호
• /
• pp.580-585
• /
• 2022

In this study, the high-temperature dielectric constant of Si₃N₄ ceramics, a representative non-oxide-based radome material, was evaluated and the cause of the dielectric constant change was analyzed in relation to the oxidation behavior. The dielectric constant of Si₃N₄ ceramics was 7.79 at room temperature, and it linearly increased as the temperature increased, showing 8.42 at 1,000 ℃. As results of analyzing the microstructure and phase for the Si₃N₄ ceramics before and after heat-treatment, it was confirmed that oxidation did not occur at all or occurred only on the surface at a very insignificant level below 1,000 ℃. Based on this, it is concluded that the increase in the dielectric constant according to the temperature increase of Si₃N₄ ceramics is irrelevant to the oxidation behavior and is only due to the activation of charge polarization.

• 한국분말재료학회지
• /
• 제29권6호
• /
• pp.492-498
• /
• 2022

N-doped Na₂Ti₆O₁₃@TiO₂ (denoted as N-NTO@TiO₂) composites are successfully synthesized using a simple two-step process: 1) ball-milling of TiO₂ with Na₂CO₃ followed by heat treatment at 900℃; 2) mixing of the prepared Na₂Ti₆O₁₃ with titanium isopropoxide and calcining with urea at 500℃. The prepared composites are characterized using XRD, SEM, TEM, FTIR, and BET. The N-NTO@TiO₂ composites exhibit well-defined crystalline and anatase TiO₂ with exposed {101} facets on the external surface. Moreover, dopant N atoms are uniformly distributed over a relatively large area in the lattice of the composites. Under visible light irradiation, ~51% of the aqueous methylene blue is photodegraded by N-NTO@TiO₂ composites, which is higher than the values shown by other samples because of the coupling effects of the hybridization of NTO and TiO₂, N-doping, and presence of anatase TiO₂ with exposed {101} facets.

• Composites Research
• /
• 제21권2호
• /
• pp.31-35
• /
• 2008

자성 금속 코팅을 위해 폴리스티렌 submicron 입자를 제조하였다. 니켈과 철 코팅을 위해 무전해 도금을 적용하였고 열처리를 통해 폴리스티렌을 탄화 시켜 중공형 구조를 형성하였다. 이러한 중공형 자성 입자는 가볍고 효율이 우수한 전자파 흡수체 제조에 적용될 수 있다. 코팅 층의 두께, 성분 및 표면 형상은 SEM/EDS/TEM 으로 관찰하였고, 중공 자성 입자의 전자파 특성 비교를 위해 고분자 복합재료를 제조하였다. 복합재료의 투자율 측정 결과, 중공형 철이 니켈에 비해 우수하였으며 바륨 페라이트 (Barium ferrite)와 같은 기존의 자성 재료보다 우수하였다.

• 복식문화연구
• /
• 제31권1호
• /
• pp.107-123
• /
• 2023

This research studied the electrical characteristics, IR transmission characteristics, stealth functions, and thermal characteristics of infrared thermal-imaging cameras of copper-sputtered samples. Nylon samples were prepared for each density as a base material for copper-sputtering treatment. Copper-sputtered NFi, NM1, NM2, NM3, NM4, and NM5, showed electrical resistance of 0.8, 445.7, 80.7, 29.7, 0.3, and 2.2 Ω, respectively, all of which are very low values; for the mesh sample, the lower the density, the lower the electrical resistance. Measuring the IR transmittance showed that the infrared transmittance of the copper-sputtered samples was significantly reduced compared to the untreated sample. Compared to the untreated samples, the transmittance went from 92.0-64.1%. When copper sputtered surface was directed to the IR irradiator, the IR transmittance went from 73.5 to 43.8%. As the density of the sample increased, the transmittance tended to decreased. After the infrared thermal imaging, the absolute values of △R, △G, and △B of the copper phase increased from 2 to 167, 98 to 192, and 7 to 118, respectively, and the closer the density of the sample (NM5→NFi), the larger the absolute value. This proves that the dense copper phase-up sample has a stealth effect on the infrared thermal imaging camera. It is believed that the copper-sputtered nylon samples produced in this study have applications in multifunctional uniforms, bio-signal detection sensors, stage costumes, etc.

• 대한토목학회논문집
• /
• 제29권1B호
• /
• pp.91-96
• /
• 2009

LDH(Layered double hydroxide) 물질을 제조하고 이를 이용하여 비소를 흡착시키는 실험을 수행하였다. TEM을 이용하여 제조한 LDH 물질의 형상을 살펴본 결과 열처리를 거친 시료는 나노크기의 결정화된 구조를 가지고 있고 열처리를 거치지 않은 시료는 아직 결정화가 완전히 이루어지지 않았으며 크기도 마이크로 범위에서 나타났다. X선 회절분석 결과를 보면 이 같은 결과가 뚜렷이 나타났으며, 열처리를 거친 경우는 뚜렷한 결정화를 보이고 있었다. $N_2$ 흡착 및 탈착 결과를 통해 LDH가 mesoporous한 공극 형태를 가지고 있다는 것을 알 수 있었다. 비표면적은 열처리를 거친 시료가 열처리를 거치지 않은 시료보다 2배 이상 크게 나타났다. 흡착 등온 실험 결과에서도 두 시료는 비슷한 흡착량을 보이며 기존 철산화 물에 못지않은 흡착능을 나타내고 있다. 금번에 합성한 Mg Fe-LDH 물질을 이용하여 토양 및 지하수의 비소 제거 공정에 적용할 수 있음을 확인하였다.