• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.6
• /
• pp.51-58
• /
• 2006

The spray characteristics of liquid jet injected into subsonic cross-flow were investigated experimentally. Spray trajectories were captured using CCD camera. Droplet sizes were measured using PDPA and Image Express. The nozzle diameter was 0.5 mm, and its length-to-diameter ratios (L/D) ran$4.11{\times}10^6$ged from 1.0 to 6.0. Experimental results indicate that the breakup point is delayed by increasing gas momentum ratio and the penetration length is decreased by increasing Weber number. At low injection angle(${\theta}$ < $90^{\circ}$), Weber number is dominant parameter for trajectories, but at high injection angle(${\theta}$ > $90^{\circ}$), L/D is dominant parameter for trajectories rather than Weber number.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.8
• /
• pp.16-23
• /
• 2006

The effects of strake planform shapes on the vortex formation, interaction, and breakdown characteristics of double-delta wings were investigated through pressure measurements of upper wing surface and off-surface flow visualization. Three different shapes of strakes were attached to a delta wing respectively to form double-delta wing configurations and tested in a medium-sized subsonic wind tunnel. The results of the pressure measurements indicated that the strake planform having a higher sweep angle generated more concentrated vortex systems at upstream locations, which, however, tended to diffuse and break down much faster at the downstream locations. It was also found from the off-surface visualization results that the cause for the vortex concentration was due to the acceleration of coiling and merging processes between the wing and strake vortices.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.72-75
• /
• 2003

In this research, we focused on the effects of the orifice internal flow such as cavitation and hydraulic flip. The breakup characteristics such as the breakup length and trajectory were measured by changing the orifice diameter (d), the orifice length/orifice diameter (L/d), the injection pressure and the shapes (sharp and round) of orifice entrance to provide a lot of conditions of the orifice internal flow. It is found that cavitation bubbles that occur inside the sharp-edged orifice make the liquid jet ejecting from the orifice turbulent. In the orifices (L/d = 5), the hydraulic flip phenomenon is shown when the injection pressure is high. In case cavitation occurs it breaks up more earlier than that in case of non-cavitation. In case hydraulic flip occurs, since the area of the liquid jet becomes small, the breakup length is also small as that in case of cavitation. But the liquid column trajectories have a similar tendency irrespective of cavitation.

• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.4
• /
• pp.601-613
• /
• 2017

An adjoint-based error estimation and mesh adaptation study is conducted for two-dimensional viscous flows on unstructured hybrid meshes. The error in an integral output functional of interest is estimated by a dot product of the residual vector and adjoint variable vector. Regions for the mesh to be adapted are selected based on the amount of local error at each nodal point. Triangular cells in the adaptive regions are refined by regular refinement, and quadrangular cells near viscous walls are bisected accordingly. The present procedure is applied to single-element airfoils such as the RAE2822 at a transonic regime and a diamond-shaped airfoil at a supersonic regime. Then the 30P30N multi-element airfoil at a low subsonic regime with a high incidence angle (${\alpha}=21deg.$) is analyzed. The same level of prediction accuracy for lift and drag is achieved with much less mesh points than the uniform mesh refinement approach. The detailed procedure of the adjoint-based mesh refinement for the multi-element airfoil case show that the basic flow features around the airfoil should be resolved so that the adjoint method can accurately estimate an output error.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.546-549
• /
• 2009

Dynamic model for supersonic engine is proposed to design control law. The model structure is constructed to capture the local characteristics of supersonic and subsonic flow by using conservation equations. To evaluate the stability of control law under the disturbances, the air turbulence model is incorporated with the engine model. The combined model shows analogous results compared to performance analysis model which is good coincidence with CFD results and disturbance effects.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.771-774
• /
• 2002

Highly sweep leading edge extensions(LEX) applied to delta wings have greatly improved the subsonic maneuverability of contemporary fighters. In this study, systematic approach by PIV experimental method within a circulating water channel was adopted to study the fundamental characteristics of induced vortex generation, development and its breakdown appearing on a delta wing model with or without LEX in terms of four angles of attack($15^{\circ},\;20^{\circ},\;25^{\circ},\;30^{\circ}$) and six measuring sections of chord length($30{\%},\;40{\%},\;50{\%},\;60{\%},\;70{\%},\;80{\%}$). Sideslip effect in case of the LEX was also studied for two sideslip(yaw) angles($5^{\circ},\;10^{\circ}$) at one angle of attack(20). Distribution of time-averaged velocity vectors and vorticity over the delta wing model were compared along the chord length direction. Quantitative comparison of the maximum vorticity featuring the induced pressure distribution were also conducted to clarify the significance of the LEX existence. Animation presentation in velocity distribution was also implemented to reveal the effect of LEX with wing vortex interaction.

• Journal of computational fluids engineering
• /
• v.21 no.3
• /
• pp.48-54
• /
• 2016

In the present work, numerical simulations were conducted on the scaled model of the BWB type UCAV in the subsonic region using ANSYS FLUENT V15. The prediction method was validated through comparison with experimental results and the effect of the twisted wing was investigated. To consider the transitional flow phenomenon, ${\gamma}$ transition model based on SST model was adopted. The coefficients of lift, drag and pitching moment were compared with experimental results and the pressure distribution and streamlines were investigated. The twisted wing decreases the lift force but increases lift-to-drag ratio through delay of stall and leading edge vortex's movement to the front, also the non-linearity of the pitching moment is decreased.

• Composites Research
• /
• v.15 no.1
• /
• pp.1-8
• /
• 2002

In this study, the flutter analysis for a rectangular box wing and an actual fighter wing with composite shin, aluminum spar and aluminum rib has been conducted. A conservative 3D wing-box model of an actual wing is modeled by MSC/PATRAN and the corresponding free vibration analysis has been performed by MSC/NASTRAN. The finite elements of membrane, rod and shear panel are used. Using the practical ply angles, various composite laminates are composed and analysed. The DLM code which is linear aerodynamic theory in frequency domain is applied to calculate unsteady aerodynamic pressure in subsonic flow region and the V-g and p-k methods are applied to obtain the solution of aeroelastic governing equation in frequency domain.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.6
• /
• pp.77-84
• /
• 2012

The aerodynamic performance of a single-stage transonic axial compressor was experimentally evaluated by measuring pressure and temperature distribution at the inlet and outlet of the compressor. The compressor was developed by Korea Aerospace Research Institute through multidisciplinary design optimization (MDO) method, especially integrating aerodynamic performance and structural stability. The test results show that the pressure ratio is 1.65 and the efficiency is 85.8 % at design point, where the corrected speed is 22,000 rpm and the corrected mass flow rate is 15.4 kg/s, and it has a good agreement with the design target and computational results. The distribution of pressure ratio is very steep at design speed, compared with the trend of other subsonic compressors. Also the static pressure distribution on the stator casing shows that the blade loading is gradually increasing through the stage as designed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.1
• /
• pp.9-19
• /
• 2002

Accuracy of AUSM-type schemes is closely related to a speed of in a cell-interface. Effect to accuracy by a speed of sound invastigated in the region of subsonic, transonic, and supersonic flows repectively. The advantage of the speed of sound in AUSMPW+ are summerized as the improvement of accuracy in capturing an oblique shock and the removal of an expansion shock to satisfy the entropy condition. They are proven by mathmatics and numerical result. Moreover AUSMPW+ is extended to a real gas flow and the speed of sound for equilibrium and nonequilibrium gas which could give exact soultions in an oblique shock is proposed.