• Journal of the Korean Geosynthetics Society
• /
• v.17 no.1
• /
• pp.127-137
• /
• 2018

Gravel Compaction Pile (hereinafter referred to as GCP) is a ground improvement technique by packing crushed stones on fragile clay ground, pressing it, and forming stakes on the foundation. Although many researchers have analyzed stress behavior of GCP composite ground on domestic GCP technique using laboratory experiment and field experiment, analyses of stress behavior according to the difference of stiffness of mat foundation loaded on the upper foundation of GCP composite ground have not been done actively. Therefore, this study aimed to identify the stress concentration ratio in accordance with the difference of basis stiffness by interpreting figures. To perform this, replacement ratio was changed and modelled using ABAQUS, software for finite element analysis and analyzed the stress concentration ratio, amounts of settlement, and maximum amounts of horizontal displacement of composite ground in accordance with the difference of stiffness. An analysis showed that the stress concentration ratio of rigid foundation was highly assessed than unloading of flexible foundation in case of unloading, while amounts of settlement under flexible unloading condition were slightly higher than under rigid condition. This indicates that the characteristic of stress behavior on the different stiffness of upper foundation needs to be clarified. In addition, the maximum horizontal displacement was generated in a constant level regardless of the difference of stiffness.

• Journal of the Korea Concrete Institute
• /
• v.13 no.1
• /
• pp.62-68
• /
• 2001

The purpose of this paper was to investigate the relations between the unbonded tendon stress and the influential parameters which were bonded reinforcement ratio, span/depth ratio, and loading type. To this end, first, the influence of parameters were examined with twenty eight test results obtained from references. Then, an experimental study was carried out with 21 test specimens. The investigation with previous and current tests revealed the followings; (1) The bonded reinforcement ratio and prestressing ratio were proved to be an important variables on the unbonded tendon stress. (2) The ratio of span to depth and type of loading affected partially the unbonded tendon stress although their effects varied depending on bonded reinforcement ratio. (3) AASHTO LRFD Code and Moon/Lim\`s design equation predicted the test results well with some safety margins.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.11
• /
• pp.79-89
• /
• 2008

In this study, a series of undrained cyclic triaxial tests were performed with three different consolidation stress ratios ($K_c$=1.0, 1.5, 2.0) to investigate the undrained shear strength characteristics of sands with respect to the amount of contained silt located around the basin of Nak-dong River. The test results show that the more the sand has silt, the lower is cyclic shear stress ratio (CSR) in all $K_c$ and that the higher $K_c$ goes, the larger CSR decreases due to the increase of contained silt. The excessive pore pressure caused during shearing has an influence on the decrease of CSR by the high initial pore pressure in proportion to the amount of contained silt regardless of the $K_c$ value. After consolidation, the analysis of the skeleton void ratio of the sample reveals that the main cause of the decrease of CSR as well as the increase of the initial excessive pore pressure is the increase of the skeleton void ratio in proportion to the amount of contained silt.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.6 s.165
• /
• pp.1001-1010
• /
• 1999

Thermo-mechanical behavior of discontinuous shape memory alloy(SMA) reinforced polymeric composite has been studied using modified shear lag theory and finite element(FE) analysis with 2-D multi-fiber model. The aligned and staggered models of short-fiber arrangement are employed. The effects of fiber overlap and aspect ratio on the thermomechanical responses such as the thermal expansion coefficient are investigated. It is found that the increase of both tensile stress(resistance stress) in SMA fiber and compressive stress in polymer matrix with increasing aspect ratio is the main cause of low thermal deformation of the composite.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.67-72
• /
• 2002

The purpose of this study is to investigate on the measurement of stress due to autogenous shrinkage of high strength concrete according to the W/C ratio at early age. The main parameters are as follows W/C ratio is 25, 30, 40%. The size of specimen is 10$\times$10$\times$150cm and the autogenous shrinkage strain is measured by the bonded strain gauge at the inside of the specimens. From the test, it is suggested that the autogenous shrinkage stress increased as W/C ratio decreased.

• Journal of Ocean Engineering and Technology
• /
• v.5 no.2
• /
• pp.58-66
• /
• 1991

Not only difference of fatigue crack growth and propagation behavior resulted from the grain size, the hardness ratio and volume fraction in M.E.F. dual phase steel composed of martensite in hard phase and ferrite in soft phase, but also the effects of the plastic constraint were investigated by fracture mechanics and microstructural method. The main results obtained are as follows: 1) The fatigue endurance of M.E.F. steel increases with decreasing the grain size, increasing the ratio of hardness and volume fraction. 2) The initiation of slip and crack occures faster as the stress level goes higher. These phenomena result from the plastic constraint effect of the second phase. 3) The crack propagation rate in the constant stress level is faster as the grain size gets larger, the ratio of hardness lower and volume fraction smaller.

• Journal of the Korean Magnetics Society
• /
• v.4 no.2
• /
• pp.89-93
• /
• 1994

Effects of density, inner-stress, and grain size on B-H hysteresis loop properties of Mg-ferrite were investigated. As the sintered bulk density increase, coercive force($H_c$) decreasand squareness ratio increase. Coercive force was very dependent on inner-stress in sintered body, so coercive force increase from 1.95[Oe] to 4.35[Oe] when inner stress present in bulk, however, the squareness ratio was almost not changed Coercive force and squareness ratio were independent on grain size of sintered body which is between 6-11[$\mu\textrm{m}$]

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.979-986
• /
• 2008

In this study, it enforced DMT test, CPTu test, laboratory consolidation test, because it estimated stress history of Gwangyang port marine clay. Through DMT test obtained Horizontal stress index($K_D$), predicted overconsolidation ratio by $K_D$. To compare empirical equation with laboratory consolidation test and CPTu test calculated OCR examined application. The result, Powell & Uglow(1988) method underestimated OCR value in comparison with Suggestion. Comparatively Byeon wi yong(2004) and Chang(1991) method seem to exactly predict in-situ stress states. Sugawara(1988) method of CPTu test seems to underestimate OCR.

• International Journal of Concrete Structures and Materials
• /
• v.9 no.4
• /
• pp.463-473
• /
• 2015

Three full-scale instrumented test slabs were constructed and tested using a heavy vehicle simulator (HVS) to evaluate the structural behavior of internally cured concrete (ICC) for use in pavements under Florida condition. Three mix designs selected from a previous laboratory testing program include the standard mixture with 0.40 water-cement ratio, the ICC with 0.32 water-cement ratio, and the ICC mixture with 0.40 water-cement ratio. Concrete samples were prepared and laboratory tests were performed to measure strength, elastic modulus, coefficient of thermal expansion and shrinkage properties. The environmental responses were measured using strain gages, thermocouples, and linear variable differential transformers instrumented in full-scale concrete slabs. A 3-D finite element model was developed and calibrated using strain data measured from the full-scale tests using the HVS. The results indicate that the ICC slabs were less susceptible to the change of environmental conditions and appear to have better potential performance based on the critical stress analysis.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.4 s.97
• /
• pp.388-394
• /
• 2005

This paper has the object of investigating natural frequencies of tapered thick plate on Pasternak foundation by means of finite element method and providing kinetic design data for mat of building structures. Vibration analysis for tapered thick plate subjected to in-plane stress is presented in this paper. Finite element analysis of rectangular plate is done by use of rectangular finite element with 8-nodes. Analysis conditions of tapered thick plate are as follows each. The ratio of in-plane stress to critical load is varied with $0.2\sigma_{cr}$, $0.4\sigma_{cr}$, $0.6\sigma_{cr}$. The Winkler parameter is 0, 10, 100, 1000, the shear foundation parameter is 0, 10 and the taper ratio is 0.0, 0.2, 0.4, 0.6, 0.8.