• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.39 no.2
• /
• pp.158-163
• /
• 2003

Thermosetting matrix composites have disadvantages in terms of moulding time, repairability and manufacturing cost. Thus the high-performance thermoplastic composites to eliminate such disadvantages have been developed so far. As a result of environmental and economical concerns, there is a growing interest in the use of thermoplastic composites. However, since their mechanical properties are very sensitive to the environment such as moisture, temperature etc., those behaviors need to be studied. Particularly the temperature is a very important factor influencing the mechanical behavior of thermoplastic composites. The effect of temperature have not yet been fully quantified. Since engineering applications of reinforced composites necessitate their fracture mechanic characterization, work is in progress to investigate the fracture and related failure behavior. An approach which predicts the tensile strength was perpormed in the tensile test. The main goal of this work is to study the effect of temperature on the result of tensile test with respect to GF/PE composite. The tensile strength and failure mechanisms of GF/PE composites were investigated in the temperature range 6$0^{\circ}C$ to -5$0^{\circ}C$. The tensile strength increased as the fiber volume fraction ratio increased. The tensile strength showed the maximum at -5$0^{\circ}C$, and it tended to decrease as the temperature increased from -5$0^{\circ}C$. The major failure mechanism was classified into the fiber matrix debonding, the fiber pull-out, the delamination and the matrix deformation.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.05a
• /
• pp.147-153
• /
• 2006

Photocatalyst reaction has limit of its usage because application range mostly centered on atmosphere purification area. Thus, it is true that an alternative plans are necessary to increase usage of $TiO_2$ as photocatalyst material. (1) The result of flow felt according to $TiO_2$ replacement rate has shown that both of anatase type and rutile type over 12% deviated from desired flow, $110{\pm}5mm$. Consequently, the range below 9% will be suitable when the anatase type $TiO_2$ if used for functional additives if workability is considered. (2) After compressive strength test, replacement rate 6-9% is estimated as suitable range if $TiO_2$ is used as compressive strength material. Rutile type and anatase type are suitable for in early-age strength and long-age strength respectively. (3) It was revealed that bending strength was dramatically decreased when replacement rate was increased. The main reason were the increase of $TiO_2$ doesn't influence hydration reaction and the decrease of bending strength. (4) The result from the water purification properties test using ion-chromatograhpy has shown that the condition with anatase type $TiO_2$ was normally better than rutile type on the same replacement rate.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.4
• /
• pp.275-284
• /
• 2016

PURPOSE. The aim of this study was to evaluate the influence of different surface treatment methods on the microtensile bond strength of resin cement to resin nanoceramic (RNC). MATERIALS AND METHODS. RNC onlays (Lava Ultimate) (n=30) were treated using air abrasion with and without a universal adhesive, or HF etching followed by a universal adhesive with and without a silane coupling agent, or tribological silica coating with and without a universal adhesive, and divided into 6 groups. Onlays were luted with resin cement to dentin surfaces. A microtensile bond strength test was performed and evaluated by one-way ANOVA and Tukey HSD test (${\alpha}$=.05). A nanoscratch test, field emission scanning electron microscopy, and energy dispersive X-ray spectroscopy were used for micromorphologic analysis (${\alpha}$=.05). The roughness and elemental proportion were evaluated by Kruskal-Wallis test and Mann-Whitney U test. RESULTS. Tribological silica coating showed the highest roughness, followed by air abrasion and HF etching. After HF etching, the RNC surface presented a decrease in oxygen, silicon, and zirconium ratio with increasing carbon ratio. Air abrasion with universal adhesive showed the highest bond strength followed by tribological silica coating with universal adhesive. HF etching with universal adhesive showed the lowest bond strength. CONCLUSION. An improved understanding of the effect of surface treatment of RNC could enhance the durability of resin bonding when used for indirect restorations. When using RNC for restoration, effective and systemic surface roughening methods and an appropriate adhesive are required.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.24 no.4
• /
• pp.92-98
• /
• 1982

The major objective of this study was to investigate the heat resistance of epoxy resin mortar. For this purpose, these tests of compressive and bending strength were accomp- olished with various heating temperature (40˚C, 60˚C, 80˚C, 100˚C, 120˚C), and with various mixing ratio (1: 2, 1: 4, 1: 6, 1: 8, 1:10, 1:12, 1:14). The exprimental resin was to be Epi-Bis type epoxy resin, which is widely used as construction materials. The results obtained are summarized as follows; 1. The variations of color tone started to begin at 60˚C, and it has come out very heavy at 120˚C. It was assumed that the decrement of weight resulted from carbonization were about 0.22% at 100˚C, and about 0.34% at 120˚C. 2. The compressive and bending strength were increased with temperature rise up to 80˚C, but these were made rapid decrease when the given temperature was over. And so, the mean decrement of compressive and bending strength at 120˚C reached up to 35.5% and 26.4%, respectively. 3. The regression equation between compressive and bending strength for epoxy resin mortar under heat exposure were obtained as follows; od=0. 371oc+39. 23 (r=0. 986) And the estimated value of bending strength was corresponded to about 37 percent in comparing with that of the compressive strength. 4. Consquently, the heat resistance temperature of epoxy resin mortar was to be around 80˚C, and it was generally very low values. But it was regarded that the epoxy resin mortar will not be difficult with materials of civil engineering works and agricultural structures.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.598-603
• /
• 2012

MgO based cement for the low-temperature calcination of magnesite required less energy and emitted less $CO_2$ than the manufacturing of Portland cements. Furthermore, adding reactive MgO to Portland-pozzolan cement can improve their performance and also increase their capacity to absorb atmospheric $CO_2$. In this study, the basic research for magnesia cement using $MgCO_3$ and magnesium silicate ore (serpentine) as starting materials was carried out. In order to increase the hydration activity, $MgCO_3$ and serpentinite were fired at a temperature higher than $600^{\circ}C$. In the case of $MgCO_3$ as starting material, hydration activity was highest at $700^{\circ}C$ firing temperature; this $MgCO_3$ was completely transformed to MgO after firing. After the hydration reaction with water, MgO was totally transformed to $Mg(OH)_2$ as hydration product. In the case of using only $MgCO_3$, compressive strength was 35 $kgf/cm^2$ after 28 days. The addition of silica fume and $Mg(OH)_2$ led to an enhancements of the compressive strength to 55 $kgf/cm^2$ and 50 $kgf/cm^2$, respectively. Serpentine led to an up to 20% increase in the compressive strength; however, addition of this material beyond 20% led to a decrease of the compressive strength. When we added $MgCl_2$, the compressive strength tends to increase.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.2
• /
• pp.181-194
• /
• 1999

Both the chemical components and the physical and mechanical properties of the compacted and undisturbed weathered granite soils were estimated to investigate the influences of the degree of weathering and saturation on the shear strength. The weathered granite soils used in this study were taken from six different sites in Korea. The results showed that the shear strength of weathered granite soil decreased with increasing the degree of weathering and saturation. Under the normal stresses less that 40kPa, the shape of Mohr-Coulomb failure envelope followed curved or hyperbolic relationship and a half of cohesion value obtained by the common shear test was observed. Using the Sueoka's method, the values of CWI were ranged from 21.5 to 31.26 which can be characterized as a completely weathered granite soil. Large decrease in shear strength and remarkable variation in dilatancy were observed in saturated granite soil compared to unsaturated soil. It was also found that the shear strength of undisturbed weathered granite soil of Pungam site can be expressed approximately by the equation of ${(\tau)_{sat}= 1.0(\tau)_{unsat}-12.48}$ and this equation can be extended to the other sites considered in this study.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.1
• /
• pp.42-48
• /
• 2001

Over two decades, many researchers have performed studies on strength size effects in composite laminates under tensile and flexural loads. It is well known that there is a tendency for the strength of fibre-reinforced composites to decrease with increasing specimen size. Under compressive load, however, little work has been done on the effect of specimen size to failure strength. This is due to the fact that compressive testing of composite is very difficult. In this paper, the effect of the test specimen size on the compressive strength of composites containing open hole was considered using T300/924C, $>[45/-45/0/90]_{3S}$. For sizing test specimens, the in-plane scaling method is used i.e., the change of two- dimensional specimen area in specimen width and gauge length. The results clearly show that there is a hole size effect in the finite width plates. In addition, the specimens which have the same a/W(hole diameter/specimen width) exhibit a tendency of size effect. In contrast, test results of the unnotched specimens did not show a clear strength size effect.

• Korean Journal of Materials Research
• /
• v.14 no.2
• /
• pp.126-132
• /
• 2004

The high strength steel sheets has been widely used as the automobile parts to reduce the weight of a vehicle. The aim of this research is to develop the TRIP aided high strength low carbon steels using reverse transformation process. The 0.15C-4Mn and 0.15C-6.5Mn steel sheets were reversely transformed by slow heating to intercritical temperature region and air cooling to room temperature. The stability of retained austenite depends on the enrichment of carbon and manganese by diffusion during the reverse transformation. The amount of retained austenite formed after reversely transformed at $645^{\circ}C$ for 12 hrs. was about 46vol.% in hot rolled 0.lC-6.5Mn steel. The change in volume fraction of retained austenite with a holding temperature was consistent with the changes in elongation and the strength-ductility combination. The tendency of tensile strength to increase with increasing the holding temperature was due to the decrease of retained austenite after cooling from the higher temperature of $670 ^{\circ}C$. The maximum strength-ductility combination was about 4,250 kg/$\textrm{mm}^2$ㆍ% when the hot rolled 0.lC-6.5Mn steel was reversely transformed at $645^{\circ}C$ for 12 hrs.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.7
• /
• pp.29-40
• /
• 2020

In this study, various laboratory tests were conducted to evaluate the effect of the moisture conditions of Jeju basalt on the mechanical properties. Twenty specimens were produced respectively from basalts collected from Sangga-ri and Eoeum-ri in northwestern Jeju. The tests were performed under saturated and dry conditions, and the results of these tests were used to examine the relationship with the physical properties and the mechanical properties depending on the moisture conditions. As a result of analysis with the test results and references, it was found that the uniaxial compressive strength, Brazilian tensile strength and elastic modulus in the saturated condition decrease at a similar ratio as compared with the dry condition. Also, the Brazilian tensile strength and the uniaxial compressive strength were in a linear proportional relationship, and in the moisture conditions, this relationship was not significantly affected.

• Journal of the Korea Concrete Institute
• /
• v.14 no.1
• /
• pp.41-48
• /
• 2002

In this paper, permeable polymer concretes with unsaturated polyester or vinylester resin content from 5 to 8 weight ％, resin-filler ratio of 1 : 1, sand content from 0 to 15 weight ％ and crushed stone of size 2.5∼10 mm were prepared, and tested for compressive strength, flexural strength and water permeability. The effects of the resin and sand contents on the properties of permeable polymer concrete were discussed. It is concluded from the test results that increase in the strength and decrease in the coefficient of permeability of the permeable polymer concrete arc clearly observed with increasing the resin and sand contents. The permeable polymer concrete showed compressive strength in the range of 170 to 350 kgf/$\textrm{cm}^2$ and flexural strength in the range of 40 to 90 kgf/$\textrm{cm}^2$ at coefficient of permeability from 0.1 to 1.0 cm/sec in this experiment.