• Journal of the Korean Geotechnical Society
• /
• v.32 no.10
• /
• pp.41-53
• /
• 2016

Stability of the braced earth wall in the composite ground, which is composed of the jointed base rocks and the soil strata depends on the earth pressure acting on it. In most cases, the earth pressure is calculated by the empirical method, in which base rocks are considered as a soil strata with the shear strength parameters of base rocks. In this case the effect of the joint dips of the jointed base rocks is ignored. Therefore, the calculated earth pressure is smaller than the actual earth pressure. In this study, the magnitude and the distribution of the earth pressure acting on the braced wall in the composite ground depending on the joint dips of the base rocks and the ratio of soil strata and base rocks were experimentally studied. Two dimensional large-scale model tests were conducted in a large scale test facility (height 3.0 m, length 3.0 m and width 0.5 m) by installing 10 supports in a scale of 1/14.5. The test ground was presumed with the base rock ratio of the composite ground of 65%:35% and 50%:50% and with the joint dips for each base rock layer, $0^{\circ}$, $30^{\circ}$, $45^{\circ}$ and $60^{\circ}$, respectively. And then finite element analyses were performed in the same condition. As results, the earth pressure on the braced wall increased as the base rock layer's joint dips became larger. And earth pressure at the rock layer increased as the rock rate became larger. The largest earth pressure was measured when the base rock rate was 50% (R50) and the rock layer's joint dips was $60^{\circ}$. Based on these results, a formular for the calculation of the earth pressure in the composite ground could be suggested. Distribution of earth pressure was idealized in a quadrangular form, in which the magnitude and the position of peak earth pressure depended on the rock ratio and the joint dips.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.46 no.7
• /
• pp.833-840
• /
• 2017

For wide application of perilla leaf, which has various healthy functions and can be easily cultured across Korea, the physicochemical and sensory properties of pan bread made with various amounts of squeezed perilla leaf juice (SPLJ) were analyzed. When dough characteristics were analyzed by using farinograph, consistency and dough development time were not significantly different between the control and bread dough made with various amounts of SPLJ, whereas dough stability time increased with increasing SPLJ amount. Expansion rate of dough decreased with increasing SPLJ amount. The volume, specific volume, and baking loss rate of pan bread made with various SPLJ amounts decreased with increasing SPLJ amount. Pan bread crumb colors became thickened and greenish with increasing SPLJ amount. For physical properties of pan bread made with various SPLJ amounts, springiness and cohesiveness decreased with increasing SPLJ amount, whereas brittleness, chewiness, and hardness increased with increasing SPLJ amount. In the sensory strength analysis, pore uniformity and soft texture decreased with increasing SPLJ amount, whereas crumb color (dark greenish), perilla leaf odor, perilla leaf taste, and chewing texture increased with increasing SPLJ amount. In the overall acceptance analysis, 1.5% SPLJ was the most preferred with a score of 7.10. However, statistical differences between 1.5% and 1.0% SPLJ were not detected at P<0.05. In the partial least squares analysis, consumers liked bread with a green crumb color, perilla leaf odor, perilla leaf taste, and soft and chewing texture. In conclusion, physicochemical properties of pan bread made with SPLJ were less desirable than those of the control; however, consumer acceptance of pan bread made with 1.5% SPLJ was shown the highest. Therefore, methods for increasing physicochemical properties of pan bread made with SPLJ need to be developed for wide application of perilla leaf.

• Tuberculosis and Respiratory Diseases
• /
• v.60 no.1
• /
• pp.44-48
• /
• 2006

Background : Isoniazid (INH) is one of the most effective anti-tuberculosis (TB) drugs. In Korea, the dose of INH normally used in patients over 50 kg is 400 mg/day, which differs from the dose recommended by other countries. Indeed, the metabolism of INH shows ethnic variations, and Koreans are predominantly rapid acetylators. However, two reports suggested 300 mg of INH might be sufficient to reach an ideal peak level in Korean patients over 50 kg. Therefore, the aim of this study was to compare the effectiveness and adverse reactions between INH 300 mg and 400 mg in Korean TB patients. Method : Patients who were culture-positive, susceptible to all 1st-line drugs, initially on HREZ, and weighed over 50 kg were selected from patients with pulmonary TB between April 2003 and March 2005. The treatment results and adverse reactions in the INH 300 mg and 400 mg group were compared. Since April 2004, most TB patients at Asan Medical Center were administered INH 300 mg irrespective of the body weight. Results : The study included 123 patients in the 300 mg INH group and 128 in the 400 mg INH group. There were no significant differences between the groups in terms of age, gender, weight, history of TB treatment, initial smear strength, and frequency of cavitary lesions. There was no difference in the treatment duration between the groups. One hundred eleven (90%) patients in the INH 300 mg group and 102 (80%) in the INH 400 mg group completed treatment (p>0.05). There were no differences in the frequency of modification of the initial regimen between groups due to any adverse reactions (300 mg : 9.0%, 400 mg : 13.7%) and hepatotoxicity (300 mg : 2.7% ; 400 mg : 7.8%). Conclusion : Considering treatment results and adverse reactions of two groups, 300mg of INH may be sufficient for treating Korean TB patients. Further studies comparing the frequency of relapse will be needed.

• Journal of Korea Port Economic Association
• /
• v.35 no.4
• /
• pp.1-16
• /
• 2019

The purpose of this study is to Analyze the problems that container shipping companies exist through the commercialization of container shipping for Non-Arctic countries and the opportunity factors for the transport of the Arctic shipping to improve cooperation cross-border relation Arctic policy and the use of transport. In order to design a hierarchy analysis method study model, four high and 17 low factors were extracted by designing a hierarchy analysis method study model based on results by prior study and in-depth interview. The first of the higher factors is the internal strength of assessing the value of the Arctic, the will and capabilities of the shipping companies in creating new markets with the vision and goals of the shipping companies. Second, the internal constraints associated with the shipping companies advance to the NSR mean the negative factors for the entry into the NSR and the internal weaknesses that cause the shipping companies capacity limitations. Third, the economic benefits from the use of NSR are external factor for shipping companies in cooperation with the future economic value of the Arctic and with respect to Arctic sea and Arctic advance and development from Arctic coastal countries. Finally, external pre-emptive tasks means to respond to use NSR by external restrictions on transport to prepare the possibility of severe weather conditions, the customs policy change of coastal countries.

• The Journal of the Petrological Society of Korea
• /
• v.19 no.1
• /
• pp.31-49
• /
• 2010

Nearly NS-trending Fe-Ti ore bodies intermittently occur in the Hadong anorthosites, south Korea, irrespective of the rock types of the anorthosites. In order to determine their occurrence mode and deformation history, we collected the features of occurrence and geological structures in the field, petrographic features using thin sections of the principal constituent rocks, and geochemical data of ilmenites in the ore body using electron probe microanalysis. Fe-Ti ore bodies examined in this study are divided into two types: dike- and lamina-types. It is steadily supported that the dike-type has intruded into the anorthositic rocks after their emplacement and solidification. And the laminar-type is probably a result of the mylonitization and transposition of the dike-type ore bodies parallel to the shear planes, due to later strong dextral ductile shearing. In the meantime, the Fe-Ti ore bodies have experienced the stronger dextral shearing in the more northern part of the study area, i.e. Cheongryong-ri, Wolhoeng-ri, Jonghwa-ri, and Jayangri and Baekun-ri in ascending order of its strength, together with the less content of $TiO_2$. All ilmenites of the ore bodies have very similar chemical composition, as pure ilmenite of 52~55 wt.% in $TiO_2$ content, irrespective of the occurrence mode and degree of later ductile shearing of the ore bodies. And they didn't experience to exsolve into magnetite. The structural data indicate that the Hadong anorthosites have deformed by NNE-trending folding, intrusion of the Fe-Ti ore bodies, NNW~NNE-trending dextral ductile shearing, NW~NNW-trending sinistral semi-brittle shearing, and intrusion of NNE~NE-trending mafic dykes in descending order of chronology after the formation of foliation of the anorthositic rocks. The foliation is interpreted as a result of the accumulation of crystals that settle out from the magma by the action of gravity.

• Clean Technology
• /
• v.24 no.2
• /
• pp.127-134
• /
• 2018

To reduce the environmental pollution by $NO_x$ from ship engine, International maritime organization (IMO) announced Tier III regulation, which is the emmision regulation of ship's exhaust gas in Emission control area (ECA). Selective catalytic reduction (SCR) process is the most commercial $De-NO_x$ system in order to meet the requirement of Tier III regulation. In generally, commercial ceramic honeycomb SCR catalyst has been installed in SCR reactor inside marine vessel engine. However, the ceramic honeycomb SCR catalyst has some serious issues such as low strength and easy destroution at high velocity of exhaust gas from the marine engine. For these reasons, we design to metallic structured catalyst in order to compensate the defects of the ceramic honeycomb catalyst for applying marine SCR system. Especially, metallic structured catalyst has many advantages such as robustness, compactness, lightness, and high thermal conductivity etc. In this study, in order to support catalyst on metal substrate, coating slurry is prepared by changing binder. we successfully fabricate the metallic structured catalyst with strong adhesion by coating, drying, and calcination process. And we carry out the SCR performance and durability such as sonication and dropping test for the prepared samples. The MFC01 shows above 95% of $NO_x$ conversion and much more robust and more stable compared to the commercial honeycomb catalyst. Based on the evaluation of characterization and performance test, we confirm that the proposed metallic structured catalyst in this study has high efficient and durability. Therefore, we suggest that the metallic structured catalyst may be a good alternative as a new type of SCR catalyst for marine SCR system.

• The Journal of the Petrological Society of Korea
• /
• v.26 no.1
• /
• pp.45-54
• /
• 2017

The characteristics of the rock cleavage in Jurassic Geochang granite were analysed using the distribution of microcrack lengths and spacings. The phases of distribution of the above lengths and spacings were derived from the enlarged photomicrographs(${\times}6.7$) of the thin section. First, the length and spacing-cumulative diagrams for the six directions of rock cleavages were arranged in increasing order($H2{\rightarrow}R1$) on the density(${\rho}$) of microcrack length. The various parameters were extracted through the combination of the above two types of diagrams. The discrimination factors representing the three quarrying planes and three rock cleavages were acquired through the mutual contrast between the values of parameters. The analysis results of the research are summarized as follows. The evaluation for the six directions of rock cleavages was performed using the parameters such as (1) intersection angle(${\alpha}-{\beta}$) and (2) exponent difference(${\lambda}_S-{\lambda}_L$) between two exponential straight lines related to spacing(${\alpha}$, ${\lambda}_S$) and length(${\beta}$, ${\lambda}_L$). The values of parameters(1 and 2) are in order of H(hardway, (H1 + H2)/2) < G(grain, (G1 + G2)/2) < R(rift, (R1 + R2)/2). On the contrary, the values of the above two parameters for three planes are in order of R < G < H. Meanwhile, the direction of convergence between two exponential straight lines was derived. The above direction is compliant to arrangement of the line os' centering around the line ol. The above two lines converge in the direction of the Y-axis when the line ol and line os' occupy the upper region on the left and the lower region on the right, respectively(R-type). On the contrary, the above two lines converge in the direction of the X-axis when the order of arrangement between line ol and line os' is reversed(H-type). Especially, the positive(+) or negative(-) value of intersection angle(${\alpha}-{\beta}$) is determined by the arrangement of two vertical lines. This type of correlation analysis is useful for evaluating the relative strength of rock cleavage and discriminating three quarrying planes.

• Journal of the Korean Chemical Society
• /
• v.8 no.1
• /
• pp.20-24
• /
• 1964

The linear combination of bond orbitals method is used to investigate the reactivity of halomethanes in abstraction reactions by atoms. The activation energy is evaluated on the assumption that, in an activated complex, two electrons in a bond to be broken become completely isolated from the rest of the ${\sigma}$-electron systems. Such a model leads to an intuitively attractive concept that the interactions between the reactive bond and the neighboring bonds govern the reactivity of ${\sigma}$-electron systems. The resulting equation for the activation energy, ${\varepsilon},\;is:\;{\narepsilon}= ${\varepsilon}={\zeta}+$$${\sum}_{i=1}^3$${\eta}c-I,$ c-4 Here, subscript C-4 indicates the bond to be broken, while C-i represents the other three bonds surrounding the reactive bond; ξ is the activation energy of a hypothetical reaction of an isolated C-4 bond and an attacking atom; and ${\eta}$C-i,C-4 stems from the stabilizing interacting of C-4 bond with neighboring C-i bonds. A choie of η′s consistent with bond strength data simplifies the above equation to a form ${\varepsilon}={\zeta}\;+\;N{\eta}c$-H, C-4 where N denotes the number of C-H plus C-F bond in halomethanes. In agreement with this equation, experimental -values increase linearly with increasing N.

• Journal of the Korean Chemical Society
• /
• v.44 no.5
• /
• pp.403-409
• /
• 2000

The formation and dissociation rates of $Zn^{2+}$ Complexes with l,4,7,10-tetraaza-13,16-diox-acyclooctadecane-N,N',N",N'"-tetraacetic acid (1), 1,4,7,10-tetraaza-13,16- dioxacyclooctadecane-N,N',N",N'"-tetramethylacetic acid (2), and 1,4,7,10-tetraaza-13,16- dioxacyclooctadecane-N,N',N",N'"-tetrapropionic acid(3) have been measured by stopped-flow and conventional spectrophotometry. Observations were made at 25.0$\pm$0.1 $^{\circ}C$ and at an ionic strength of 0.10 M NaClO$_4$. The formation reactions of $Zn^{2+}$ ion with 1 and 2 took place by the rapid formation of an intermediate complex (ZnH$_3L^+$) in which the $Zn^{2+}$ ion is incompletely coor-dinated. This might then lead to be a final product in the rate-determining step.ln the pH range 4.76-5.76, the diprotonated (H2L2-) form is the kinetically active species despite of its low concentration. The stability con-stants (log$K_{(ZnH$_3$3$L^+$)}$) and specific water-assisted rate constants (koH) of intermediate complexes have been deter-mined from the kinetic data. The dissociation reactions of $Zn^{2+}$ complexes of 1,2, and 3 were investigated with $Cu^{2+}$ ions as a scavenger in acetate buffer. All complexes exhibit acid-independent and acid-catalyzed con-tributions. The effect of buffer and $Cu^{2+}$ concentration on the dissociation rate has also been investigated. The ligand effect on t dissociation rate of $Zn^{2+}$ complexes is discussed in terms of the side-pendant armsand the chelate ring sizes of the ligands.

• Food Science and Preservation
• /
• v.19 no.2
• /
• pp.193-200
• /
• 2012

The quality characteristics of $kalopanax$ $pictus$ and Aralica elata shoots during their preservation were investigated according to the salt conditions and storage temperatures to improve the use of the shoots. The results were as follows: the pH of $kalopanax$ $pictus$ shoots duing their storage did not changes with 10% and 12% brine at $4^{\circ}C$ and with 12% brine at $10^{\circ}C$. The pH of $Aralica$ $elata$ shoots is at $4^{\circ}C$ tended to be similar to the $kalopanax$ $pictus$ shoot and decreased at the storage temperature of $10^{\circ}C$. The salinity of the $kalopanax$ $pictus$ and $Aralica$ $elata$ shoots tended to increase during their storage and did not change significantly as their storage temperature changed. The L values of $kalopanax$ $pictus$ and $Aralica$ $elata$ shoots tended to decrease gradually during their storage, and the salt concentrations appeared high. The b value of the $kalopanax$ $pictus$ shoot tended to increase and that of the $Aralica$ $elata$ shoots, to decrease gradually. The a value tended to increase gradually but did not differ with variations in the storage temperatures and salt concentrations. The strength and the hardness of the $kalopanax$ $pictus$ and $Aralica$ $elata$ shoots tended to decreased gradually during their storage and highest in 10% brine at $4^{\circ}C$, and those of $Aralica$ $elata$ shoots were highest in 8-10% brine at $4^{\circ}C$. The Chlorophyll contents of the $kalopanax$ $pictus$ and $Aralica$ $elata$ shoots tended to decrease during their salt storage and did not change significantly as the temperatures and salt concentrations changed. Therefore, it can be concluded that the quality of $kalopanax$ $pictus$ and $Aralica$ $elata$ shoots can be maintained when the are stored in 10% brine at $4^{\circ}C$.