• 한국지반공학회논문집
• /
• 제18권4호
• /
• pp.75-83
• /
• 2002

본 연구에서는 준설토, EPS 그리고 고화재를 혼합한 경량혼합토의 역학적 특성을 일축 및 삼축압축시험을 통하여 고찰하였다. 역학적 특성은 다양한 준설토의 초기 함수비, EPS 함유율, 시멘트 함유율 그리고 양생압력에 대한 경량혼합토의 압축강도에 대하여 연구하였다. 삼축압축상태에서 EPS를 함유한 경량혼합토의 압축강도는 유효구속압에 의존 하지 않는 것으로 나타났다. EPS 함유율이 감소할수록($A_E$<2%) 그리고 시멘트 함유율이 증가할수록($A_c$>2%) 삼축압축강도-변형 거동특성은 극한 압축강도를 지나 급격한 압축강도의 감소를 보이는 시멘트 혼합토의 압축강도-변형 거동특성과 유사한 것으로 나타났다. 200kpa 이상의 압축강도를 요구하는 개량지반에 본 경량혼합토를 적용하는 경우에서 적절한 준설토의 초기함수비, EPS 함유율은 각각 약 165%~175%이상 그리고 3%~4%이상으로 제시할 수가 있었다. 삼축 및 일축압축상태에서 극한 압축강도는 시멘트 함유율이 2%이상에서 거의 증가하지 않음으로서 한계 시멘트 함유율은 2%로 제시할 수가 있었다.

• 한국기계가공학회지
• /
• 제3권3호
• /
• pp.79-85
• /
• 2004

The lightness of components required in automobile and machinery industry is requiring high strength of components. In particular, fatigue failure phenomena, which happen in metal, bring on danger in human life and property. Therefore, antifatigue failure technology takes an important part of current industries. Currently, the shot peening is used for removing the defects from the surface of steel and improving the fatigue strength on surface. Therefore, in this paper the effect of compressive residual stress of spring steel(JISG SUP-9)by shot peening on fatigue crack growth characteristics in stress ratio(R=0 1, R=0 3, R=0 6)was investigated considering fracture mechanics. By using the methods mentioned above, I arrived at the following conclusions: (1) The fatigue crack growth rate(da/dN) of the shot peening material was lower than the unpeening material And in stage I, ${\Delta}K_{th}$, the threshold stress intensity factor, of the shot peening material is high in critical parts unlike the unpeening material. (2) Fatigue life shows more Improvement in the shot peening material than in the unpeening material. And compressive residual stress of surface on the shot peening processed operate the resistance of fatigue crack propagation.

• Computers and Concrete
• /
• 제11권2호
• /
• pp.149-167
• /
• 2013

The complete stress-strain behavior of steel fiber reinforced concrete in compression is needed for the analysis and design of structures. An experimental investigation was carried out to generate the complete stress-strain curve of high-performance steel fiber reinforced concrete (HPSFRC) with a strength range of 52-80 MPa. The variation in concrete strength was achieved by varying the water-to-cementitious materials ratio of 0.40-0.25 and steel fiber content (Vf = 0.5, 1.0 and 1.5% with l/d = 80 and 55) in terms of fiber reinforcing parameter, at 10% silica fume replacement. The effects of these parameters on the shape of stress-strain curves are presented. Based on the test data, a simple model is proposed to generate the complete stress-strain relationship for HPSFRC. The proposed model has been found to give good correlation with the stress-strain curves generated experimentally. Inclusion of fibers into HPC improved the ductility considerably. Equations to quantify the effect of fibers on compressive strength, strain at peak stress and toughness of concrete in terms of fiber reinforcing index are also proposed, which predicted the test data quite accurately. Compressive strength prediction model was validated with the strength data of earlier researchers with an absolute variation of 2.1%.

• 한국해양공학회지
• /
• 제14권2호
• /
• pp.99-105
• /
• 2000

This paper describes the effect of specimen size on fatigue crack growth rate for the offshore structural high-tensile-strength steel BS4360 and machine structural steel SM45C. The purpose of the present study is to investigate the effect of stress ratio aspect ratio specimen width and specimen thickness of the fatigue crack growth behavior. Compact tension specimens with a LT orientation for BS4360 and SM45C steels were used, All testing was done at constant stress intensity factor range controlled fatigue crack growth condition. The investigation demonstrates that the fatigue crack growth rate is increased with increasing stress ratio and specimen thickness and is decreased with increasing specimen width. The fatigue crack growth rate is unaffected by aspect ratio until a/W=0.50 but is increased by increasing spect ratio from a/W=0.55.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.916-923
• /
• 2005

In this study, to observe aging effect of undrained shear behavior for Nak-Dong River sand, undrained static and cyclic triaxial tests were performed with changing relative density ($D_r$), consolidation stress ratio($K_c$) and consolidation time. As a result of the test, the modulus of elasticity to all samples estimated within elastic zone by the micro strain of about 0.05% in case of static shear behavior increased with the lapse of consolidation time significantly, so aging effect was shown largely. Also strength of phase transformation point(S_{PT}$) and strength of critical stress ratio point($S_{CSR}$) increased with the lapse of consolidation time. Undrained cyclic shear strength($R_f$) obtained from the failure strain 5% increased in proportion to relative density($D_r$) and initial static shear stress($q_{st}$), $R_f$ of consolidated sample for 1,000 minutes increased about 10.6% compared to that for 10 minutes at the loose sand, and $R_f$ increased about 7.0% at the medium sand. In situ application range of $R_f$ to the magnitude of earthquake for Nak-Dong River sand was proposed by using a increasing rate of $R_f$ as being aging effect shown from this test result.

• 한국농공학회논문집
• /
• 제52권3호
• /
• pp.73-79
• /
• 2010

In the present study, the loading frequency dependencies of cyclic shear strength and elastic shear modulus of reconstituted clay were examined by performing undrained cyclic triaxial tests and undrained cyclic triaxial tests to determine deformation properties. The result of undrained cyclic triaxial test of reconstituted and saturated clay shows that a faster frequency leads to higher stress amplitude ratio, but when the frequency becomes fast up to a certain point, the stress amplitude ratio will reach its maximum limit and the frequency dependence becomes insignificant. And also, the result of undrained cyclic triaxial deformation test shows a fact that a faster loading frequency leads to higher equivalent shear modules and smaller hysteresis damping ratio, and confirms the frequency dependence of cohesive soil. Meanwhile, the result of the creep test shows that continuing creep is created in the undrained cyclic triaxial test with slow loading frequency rate, and since loading rate becomes slower at the vicinity of the maximum and the minimum deviator stress due to sine wave loading, the vicinity of the maximum and the minimum deviator stress shall be more influenced by creep.

• 한국정밀공학회지
• /
• 제15권1호
• /
• pp.130-136
• /
• 1998

A procedure of stress and strength analysis has been proposed for the centrifuge rotor of composite materials of quasi-isotropic laminates. The goal in this study is to maximize the allowable rotating speed, that is, to minimize maximum strength ratio with the given path length by changing the geometric parameter-outer radius and ply angles in quasi-isotropic laminates. Optimum values of the geometric parameter-outer radius and ply angles are obtained by multilevel optimization. All the geometric dimensions and stresses are normalized such that the result can be extended to a general case. Two dimensional analysis at each cross section with an elliptic tube hole subjected to internal hydrostatic pressures by samples as well as the centrifugal body forces has been performed along the height to calculate the stress distribution with the plane stress assumption, and Tsai-Wu failure criterion is used to calculate the strength ratio. The maximum allowable rotating speed can be increased by changing the radii of the outer surface along the height with the maximum strength ratio under the unit value : The optimal number of ply angles maximizing the allowable rotating speed in quasi-isotropic laminates is found to be the half number of tube hole, and the optimal laminate rotation angle is the half of $[{\pi}/m]$. A $[{\pi}/3]$ laminate, for instance, is stronger than a $[{\pi}/4]$ laminate for the centrifuge rotor of 6 tube hole number even though they have the same stiffness.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권4호
• /
• pp.385-393
• /
• 2007

The strength evaluation of the most weakest junction part is required for the safety design of all structures. Most of all. in order to enhance the reliability and safety of the welding part. whose use is the highest, it is very important to establish the efficient structure manufacturing technology by studying and investigating the evaluation of fatigue strength in various environments. This study analyzed the relations of da/dN, and th according to the welding methods of SMAW, FCAW, and SAW. In the stage II. the value of stress intensity factor range was the highest in SMAW welding method of stress ration R=0.1, and appeared under the sequence of FCAW and SAW and as the completion section of stress intensity factor was low, threshold stress intensity factor was lowly formed in da/dN - The fatigue life of each welding method is sensitively worked in high stress ratio. judging from the fact that the width of life reduction increases in the high stress ratio zone compared to the width of life reduction in the low stress ratio zone. In the fatigue limit of welding methods before corrosion. the welding of SMAW and FCAW shows the same fatigue limit compared to Base metal, and SAW holds the lowest fatigue limit value.

• 한국지반신소재학회논문집
• /
• 제13권2호
• /
• pp.49-57
• /
• 2014

본 연구에서는 남극 장보고기지 부근에서 채취한 시료를 활용하여 동하중에 대한 액상화 저항특성을 파악하기 위하여 반복삼축시험을 실시하였다. 또한 기존문헌과의 비교를 통하여 남극에서 퇴적된 지반의 동적거동을 규명하였다. 시험결과 동일한 압밀응력비에 대한 반복회수와 축변형률 5%를 발생시키는데 필요한 반복응력비와의 관계는 모든 시료에서 초기액상화를 발생시킬 수 있는 반복응력비가 증가할수록 반복회수가 감소하였다. 세립분 함유량이 10%로 증가할수록 액상화 저항강도가 감소하다가 다시 증가하는 경향을 나타내었다. 점착력과 액상화 저항강도와의 관계는 세립분 함유량과 액상화 저항강도와의 관계와 같이 점착력이 증가할수록 액상화 저항강도도 감소하지만 어느 시점 이후에는 반복응력비가 증가하는 경향을 보였다. 또한, 마찰각과 평균입경이 증가할수록 반복응력비가 증가하는 경향을 나타내었다.

• 대한기계학회논문집B
• /
• 제27권7호
• /
• pp.920-928
• /
• 2003

The objective of the present study was to investigate the characteristics of flow and wall shear stress under steady and pulsatile flow in the aneurysm. The numerical simulation using the software were carried out for the diameter ratios ranging from 1.5 to 3.0, Reynolds number ranging from 900 to 1800 and Womersley number, 15.47. For steady flow, it was shown that a recirculating vortex occupied the entire bulge with its core located closer to the distal end of the bulge and the strength of vortex increased with increase of the Reynolds number and diameter ratio. The position of a maximum wall shear stress was the distal end of the aneurysm regardless of the Reynolds number and diameter ratios. For the pulsatile flow, a recirculating flow at the bulge was developed and disappeared for one period and the strength of vortex increased with the diameter ratio. The maximum values of the wall shear stress increased in proportion to the diameter ratio. However, the position of a maximum wall shear stress was the distal end of the aneurysm regardless of the diameter ratios.