• Journal of Welding and Joining
• /
• v.23 no.3
• /
• pp.34-39
• /
• 2005

It is required for the steel materials used in the sour environment to have sufficient resistance to hydrogen induced cracking(HIC). For line pipe steels, HIC resistance could be varied during pipe making process due to the large plastic deformation applied in the thick-wall pipe. In order to figure out such effect, HIC tests were performed not only in the plate condition but in the pipe condition and their results were compared in terms of cracking ratio. Test results demonstrated a detrimental effect of plastic deformation to HIC resulting in a substantial increase in the cracking ratio after pipe forming process. All of the cracks found in the pipe material were located in the outer layer of pipe where the tensile strain was resulted during pipe forming stage. In order to understand the HIC resistance of the pipe but in the plate condition, it was suggested to pre-strain the plate to some extent before the HIC test.

• Journal of fish pathology
• /
• v.16 no.2
• /
• pp.119-123
• /
• 2003

We have selected an valuable pmbiotic strain; Lactobacillus sakei BK19 which has wide antagonic spectrum against fish pathogens . Present study investigated cultural characterization of L. sakei BK19 including pH tolerance , susceptibility of antibacterial agents and growth pattern with different environment such as nutritions, temperature and salinity. L. sakei BK19 showed Significantly higher resistance at low pH(around pH 4) environment and relative high antibiotic tolerance . In the study of optimal culture condition, maltose and saccharose provided the optimal nutritional culture condition while lactose and mannitol were unable to supply its carbon source for the fermentation of L. sakei BK19. Moreover. L. sakei BK19 showed good growth at the temperature range of 15 to $45^{o}C$ und the NaCl concentration of 0 to 7%. Hence, this particular probiotic strain may be benificial both in seawater and fresh weter conditions.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.10a
• /
• pp.210-215
• /
• 1997

The development of rolling texture is dependent on the various rolling condition. And the geometry of rolling gab and the friction between rolls and rolled material mainly affect the type and sharpness of texture inhomogeneity through thickness. In order to follow the effect of geometry and friction various strain/pass and lubrication condition were applied during cold rolling. In this investigation various strain/pass and lubrication were applied during cold rolling in order to follow the effect rolling gap geometry and friction. More high 1/h was, more weak the ${\beta}$-fiber was and in the condition of l/h > 5 {001}<110> shear texture developed. In adition, rolling without lubrication enhanced the shear texture.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.1
• /
• pp.184-192
• /
• 1994

The parameters such as Richardson numbers or stability parameters are widely used to account for the extra straining effects due to three-dimensionality, curvature, rotation, swirl and others arising in paractical complex flows. Existing expressions for the extra strain in turbulence models such as $k-{\epsilon}$ models, however, do not satisfy the tensor invariant condition representing the coordinate indifference. In the present paper, considering the characteristics of both the mean strain rate and the mean vorticity, a new parameter to deal with the extra straining effects is proposed. The new parameter has a simple form and satisfies the tensor invariant condition. A semi-quantitative analysis between the present and previous parameters for several typical complex flows suggests that the newly proposed parameter is more general and adequate in representing the extra straining effects than the previous ad-hoc parameters.

• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.4
• /
• pp.208-218
• /
• 2006

The effects of the grain size on the magnetic properties in extra-low carbon steel after strain annealing were investigated. Two kinds of sample were prepared. One is the annealed sheet, which was annealed at $670^{\circ}C$ and $850^{\circ}C$ for various time periods after cold rolling. The other is the strain annealed sheet, which was temper rolled by 0.4% and subsequently strain annealed at the temperature ranging between $670^{\circ}C$ and $850^{\circ}C$ for various time periods. The grains after strain annealing became more coarse than those after primary annealing. The grains were coarsened due to the strain induced grain boundary migration (SIGM). It was found that the permeability tended to be increased and coercivity tended to be decreased with the increase of grain size. The optimum magnetic properties was achieved after strain annealing at $850^{\circ}C$ for 30 minites. Under this condition, the coercivity was measured to be 0.6 and the permeability was measured up to be 13000.

• Geomechanics and Engineering
• /
• v.18 no.3
• /
• pp.225-234
• /
• 2019

A numerical stepwise approach for cavity expansion problem in strain-softening rock or soil mass is investigated, which is compatible with Mohr-Coulomb and generalized Hoek-Brown failure criteria. Based on finite difference method, plastic region is divided into a finite number of concentric rings whose thicknesses are determined internally to satisfy the equilibrium and compatibility equations, the material parameters of the rock or soil mass are assumed to be the same in each ring. For the strain-softening behavior, the strength parameters are assumed to be a linear function of deviatoric plastic strain (${\gamma}p^*$) for each ring. Increments of stress and strain for each ring are calculated with the finite difference method. Assumptions of large-strain for soil mass and small-strain for rock mass are adopted, respectively. A new numerical stepwise approach for limited pressure and plastic radius are obtained. Comparisons are conducted to validate the correctness of the proposed approach with Vesic's solution (1972). The results show that the perfectly elasto-plastic model may underestimate the displacement and stresses in cavity expansion than strain-softening coefficient considered. The results of limit expansion pressure based on the generalised H-B failure criterion are less than those obtained based on the M-C failure criterion.

• 한국생물공학회:학술대회논문집
• /
• 2000.04a
• /
• pp.299-302
• /
• 2000

Actinoplanes teichomyceticus ATCC 31121 was mutated with UV to obtain a superior mutant strain with increasing level of teicoplanin production. In this investigation lethal curve was obtained and the optimal condition to induce mutagenesis was determined and to isolate the desirable mutant strain. It was also confirmed that teicoplanin activities by agar diffusion method to be compared to the mother strain. One mutant strain, T991014-1 that had the highest teicoplanin productivity was finally selected for further investigation including fermentation pattern. The mutant was characterized by the various tests such as amylase activity, protease activity, antibiotic resistance, autotoxicity, and productivity.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.97-107
• /
• 1995

Global postbuckling analysis is accomplished for one-dimensional and two-dimensional delaminations. A new finite element model, which can be used to model the global postbuckling analysis of one-dimensional and two-dimensional delaminations, is presented. In order to calculate the strain energy release rate, geometrically nonlinear analysis is accomplished, and the incremental crack closure technique is introduced. To check the effectiveness of the finite element models and the incremental crack closure technique, the simplified closed-form sloution for a through-the-width delamination with plane strain condition is derived and compared with the finite element result. The finite element results show good agreement with the closed-foul1 solutions. The present method was extended to calculate the strain energy release rate for two-dimensional delamination. For a symmetric circular delamination, the strain energy release rate shows great variation along the delamination front. and the delamination growth appears to occur perpendicular to the loading direction.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.5
• /
• pp.73-85
• /
• 1999

Yield and fracture are separated in the tensile failure of paper. Failure in the machine direction of photocopy paper is contrasted with failure in the cross-machine direction . The ratios of distortion (shape change) to dilatation (volume change) for individual elements at yield and fracture are described. The ratios of distortion to dilatation are measured and compared to predicted values of the strain energy density theory. To evaluate the effect of the angle from the principal material direction on the strain energy density theory. To evaluate the effect of the angle from the principal material direction on the strain energy density factor, samples are prepared from machine direction to cross-machine direction in 15 degree intervals. the strain energy density of individual elements are obtained by the integration of stress from finite element analysis with elastic plus plastic strain energy density theory. Poison's ratio and the angle from the principal material direction have a great effect ion the ratio fo distortion to dilatation in paper. During the yield condition, distortion prevails over dilatation . At fracture, dilatation is at a maximum.

• Transactions of Materials Processing
• /
• v.3 no.2
• /
• pp.215-228
• /
• 1994

The purpose of this paper is to pursue a general method to determine both the flow stress of a material and the friction factor by ring compression test. The materials are assumed to obey the expanded n-power hardening rule including the strain-rate effect. Ring compression is simulated by the rigid-plastic finite element method to obtain the database used in determining the flow stress and friction factor. The Simulation is conducted for various strain hardening exponent, strain-rate sensitivity, friction factor, and compressing speed, as variables. It is assumed that the friction factor is constant during the compression process. To evaluate the compatibility of the database, experiments are carried out at room and evaluated temperature using specimens of aluminum 6061-T6 under dry and grease lubrication condition. It is shown that the proposed test method is useful and easy to use in determining the flow stress and the friction factor.