• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.1280-1285
• /
• 2004

ADC railway system has low feeder voltage, The fault current can be smaller than the current of load starting. So it is important to discriminate between the small fault current and the load starting current. The load starting current increases step by step but the fault current increases all at once. As for the load starting current, the time constant of load current at each step is much smaller than that of the fault current. First, to detect faults in DC railway systems, an algorithm using the time constant calculated by the method of least squares is presented in this paper.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.253-254
• /
• 2016

This paper proposes a novel starting method of a high speed induction motor with air bearings for turbo blowers. The friction of air bearings varies according to rotating speed, operating temperature and usage time. Specially, friction torque at initial starting state under low bearing temperature usually results in starting failures of the conventional V/F control method. Therefore, this paper proposes a new starting method, which consists of an initial I/F control mode and smooth transition method to V/F control mode to overcome the starting failure. The experimental results are shown to verify the analysis and the usefulness of the proposed method.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.33 no.8
• /
• pp.316-324
• /
• 1984

In the wound rotor induction motor, the external resistor is usually added to the rotor circuit in order to limit the starting current. In this scheme, whilst the starting current is limited, the available torque is remarkably reduced. In this paper, to improve the starting characteristics the stator current can be maintained constant by adjusting the external resistor. To change the external resistor, teh chopper and the resistor is connected in parallel, and the chopper duty cycle is adjusted by microprocessor. The duty cycle is calculated according to the actual speed of motor by microprocessor look-up table map. In this suggested scheme, the starting characteristics are remarkably improved without over-current. The starting time of this system is reduced by 20-48 Percent compared with fixed extemal resistance system in the same load.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.6
• /
• pp.1007-1012
• /
• 2016

Induction motors are used widely in driving load of a fluid, such as a pump or a fan in the industry. Induction motor has been generated the voltage drop by the occurrence of a high current during startup. In addition, high start-up current can act as a mechanical stress on the shaft of the motor. So there is need a way to reduce the starting current. Soft start method is one of the many ways to reduce the starting current. This method uses silicon-controlled rectifiers(SCRs) for varying value of the voltage applied to the motor. There is a case for fixing or changing the thyristor firing angle to adjust the magnitude of the voltage. Starting power factor of induction motor is very low compared to the normal operation. Soft starting with the firing angle fixed needs to be considered a low power factor at startup. In this study, we compared the direct start characteristics and soft start characteristics considering the low power factor at the time of start-up. It was possible to confirm that the starting current and the voltage drop is present differently according to the firing angle.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1997.10a
• /
• pp.11-13
• /
• 1997

Abstract - An electronic starter using MOSFET has been designed to take advantage of ideal preheating and starting features which can extend the lifetime of fluorescent lamps. The preheating circuit of the developed electronic starter is consisted of four parts - afull-wave rectifier circuit, an FET switching circuit a timer circuit for the gate switching, and a circuit for end-of-life protection. The circuit is analyzed by using PSpice simulation, and is improved to give an appropriate starting-time through control of R-C time constant of the timer circuit. And the circuit is also provided with an end-of-life protection feature, which utilizes the negative resistance characteristics of a thermistor that is thermally linked to FET through a heatsink. This also protects the FET from any overheating problems. From the results of simulation it is possible to obtain an appropriate value on the starting time for proper ignition and also it is verified that the limit for resistance of the thermistor is dependant on the value of resistance is the timer circuit

• Journal of Power System Engineering
• /
• v.18 no.4
• /
• pp.11-16
• /
• 2014

Although smoke emitted from ships is not included in IMO(International Maritime Organiztion) regulation yet, it is one of the substance what is polluting mainly the air. Especially, its concentration is very high when an engine is started and a load is rapidly changed. This is caused by unburned fuel what is injected more than necessary quantity after combustion period. It is possible to decrease smoke concentration emitted at starting engine by controlling fuel injection quantity, but it is concerned that time to rated speed must be spent. Then a governor what can reduce the smoke concentration without a loss of time to rated speed is needed. We adopted a electro-hydraulic governor what can control dual fuel start limit function and achieved very low level of smoke concentration without greater the loss of time to rated speed.

• Transactions of Materials Processing
• /
• v.6 no.2
• /
• pp.102-109
• /
• 1997

The multistage deformation and stress relaxation were carried out to investigate the strain induced precipitation by torsion tests in the range of 1000~80$0^{\circ}C$, 0.05~5/sec for V-microalloyed steel. The starting temperature and time for the initiation of precipitation were determined by stress relaxation tests. The distribution of precipitates increased, as the strain rate increased and the mean size of precipitates was found to be about 10~30nm. The precipitation starting time$(P_s)$ decreased with increasing strain rate and the amount of pre-strain. The effect of deformation conditions on the no-recrystallization temperature$(T_nr)$ was also determined in the multistage deformation. $T_nr$ Tnr decreased with increasing the strain and strain rate. In the controlled rolling simulation, grain refinement and precipitation hardening effects could be achieved by the alternative large pass strain at the latter half pass stage under the condition of low temperature and high strain rate.

• Korean Journal of Adult Nursing
• /
• v.13 no.4
• /
• pp.620-631
• /
• 2001

Purpose: Fatigue is one of the most common complaints of cancer patients. In this study, we analyzed the change of fatigue level and general symptoms as time go by, so that, we could explain more on the mechanism and change of fatigue in relation with treatment, and explore the influencing factors. Method: The subjects of this study were 50 GI cancer patients who have visited the cancer center of A hospital in Suwon. We measured fatigue by using the Revised Piper Fatigue Scale(RPFS) at the time of starting and finishing induction chemotherapy, and starting the 2nd cycle of chemotherapy. Results: 1) The fatigue score was 2.81, 3.73, and 3.82 in a 10 point scale at the time of starting and finishing induction chemotherapy, and starting the 2nd chemotherapy, respectively. This means fatigue persisted until after the treatment. 2) Fifty two percent of participants complained of some kinds of symptoms when starting the treatment, and the proportion increased up to 92% when finishing the treatment. 3) Fatigue scores were significantly high in patients with fatigue-related symptoms than for patients without those symptoms. 4) Fatigue scores showed significant differences according to patients' general characteristics such as age, educational level, economic status, occupation, diagnosis, hematocrit, weight, and amount of sleepy. Conclusion: We have to develop intervention strategies to reduce fatigue in cancer patients in the consideration of influencing factors.

• 전기의세계
• /
• v.28 no.3
• /
• pp.72-77
• /
• 1979

The object of this paper is to try to develope Tulular Liner Induction Motor which consists of primary stator that generates traveling magnetic field from the three-phase winding of formed-wound concentric coil, and try to identify the characteristics of starting force. To indentify the theoretical starting force formular we have quoted the conventional Maxwell's basic equation and Poisson's equation which are used in the general machines thereby having obtained the formular of the current with in the conductor and of the air gap magnetic field respectively. General starting force formular is acquired by applying the formular of the current and magnetic field which was theoretically derived above. To this theoretically starting force formula various constants and the values of magnetic flux density resulting from the experimental motor are applied to present theoretically calculated values. Comparing these theoretically caculated values experimentally weighed values, we have proved the validity of theoretical research.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.379-382
• /
• 2011

Engine test as well as unload test of starting motor itself was performed to evaluate the braking characteristics of starting system used for initial spin-up of gas turbine for power generation. Through the experimental evaluation of the braking performance with the capacity of braking resistor of the starting motor, we have achieved quantitative data to secure robust braking characteristics in emergency during the starting period of the gas turbine. It is possible to establish a capacity selection criterion of braking resistor to ensure the starting reliability of the gas turbine.