• Composites Research
• /
• v.36 no.6
• /
• pp.383-387
• /
• 2023

Carbon fiber-reinforced composites have excellent mechanical properties. However, the fracture toughness is a disadvantage due to brittle failure mode. The fracture toughness can be enhanced using hybridization with large-elongation fibers. In this study, polyamide (aramid) fibers are hybridized with carbon fiber with various stacking sequences. As a result, the Izod impact strength was enhanced by 63% with 25% aramid fiber hybridization. It is also shown that there is an optimal point in laminated composite hybridization, [CF/CAF₂/CF]_s stacking sequence.

• Composites Research
• /
• v.25 no.5
• /
• pp.141-146
• /
• 2012

The strength design for the lightweight bicycle wheel made of the Carbon/Epoxy composite laminates has been discussed in this paper. For bicycle wheel design, lightness of the wheel is important. Also, it has to satisfy the required strength under specific loading cases. Two testing methods for the bicycle wheel, i.e. vertical and complex loadings, are adopted in this study. Because the strengths of composite wheel is different in relation to the stacking sequence and the number of plies, it is important to decide an appropriate stacking sequence and number of layers for the composite wheel. From the finite element analysis results, the most stable sequence orientation and number of layers are determined. The stacking sequence $[0]_{8n}$, $[90]_{8n}$, $[0/90]_{2ns}$, $[{\pm}45]_{2ns}$, $[0/{\pm}45/90]_{ns}$ (n=1,2,3,4)are performed for finite element analysis. From results, $[0/{\pm}45/90]_{3s}$ lay-up is a good selection for the composite bicycle wheel. Also, the weakest point and layer are found in this study.

• Carbon letters
• /
• v.16 no.2
• /
• pp.107-115
• /
• 2015

Impact damages induced by a low-velocity impact load on carbon fiber reinforced polymer (CFRP) composite plates fabricated with various stacking sequences were studied experimentally. The impact responses of the CFRP composite plates were significantly affected by the laminate stacking sequences. Three types of specimens, specifically quasi-isotropic, unidirectional, and cross-ply, were tested by a constant impact carrying the same impact energy level. An impact load of 3.44 kg, corresponding to 23.62 J, was applied to the center of each plate supported at the boundaries. The unidirectional composite plate showed the worst impact resistance and broke completely into two parts; this was followed by the quasi-isotropic lay-up plate that was perforated by the impact. The cross-ply composite plate exhibited the best resistance to the low-velocity impact load; in this case, the impactor bounced back. Impact parameters such as the peak impact force and absorbed energy were evaluated and compared for the impact resistant characterization of the composites made by different stacking sequences.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.28-32
• /
• 2007

Sufficient Conditions are proposed herein for analytically obtaining fully orthotropic (A16=A26=0, Bij=0, D16=D26=0) laminate stacking sequences together with a brief literature survey. A number of specially chosen anti-symmetric balanced stacking sequences are analytically studied, in which all coupling stiffnesses including B16 and B26 are identically zero. Those specially chosen anti-symmetric balanced stacking sequences are then arranged symmetrically with respect to the laminate mid-plane to obtain a number of symmetric stacking balanced stacking sequences of which the elastic stiffnesses are fully orthotropic.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.119-130
• /
• 1999

This paper deals buckling behavior of laminated composite cylindrical shells subjected to combination of axial compression and torison. Linear and nonlinear finite element analysis are carried out . the influence of load type, load ratio, fiber orientation angle, stacking sequence, and intial imperfect on buckling behavior is discussed.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.178-181
• /
• 2004

In this work, the carbon fabric reinforced phenolic composite is applied for heavy-duty journal bearings. The through thickness compressive strength (TTCS), which is one of the most important characteristics for the bearing material, is measured and analyzed with respect to the stacking sequence and composite thickness. Also, the coefficient of thermal expansion (CTE) and thermal conductivity of the composite in the thickness direction were measured with respect to stacking sequence.

• Korean Journal of Materials Research
• /
• v.19 no.8
• /
• pp.447-451
• /
• 2009

The long-period stacking order (LPSO) structures and stacking faults (SFs) in rapidly solidified powder metallurgy (RS P/M) $Mg_{97}Zn_1Y_2$ alloy were investigated by high resolution transmission electron microscopy (HRTEM) observations. The 18R-type LPSO structure with a stacking sequence of ACBCBCBACACACBABAB and a period of 4.86 nm was observed in the as-extruded RS P/M $Mg_{97}Zn_1Y_2$ alloy. After annealing at 773 K for 5 hr, the 18R-type LPSO structure was transformed to the 14H-type LPSO structure with a stacking sequence of ABABABACBCBCBC and a period of 3.64 nm. The 24R-type LPSO structure containing 24 atomic layers of ABABABABCACACACABCBCBCBC with period of 6.18 nm coexists with the 14H-type LPSO structure in the same grains. The LPSO structures contain intrinsic Type II SFs such as BCB/CABA and ABA/CBCB stacking sequences of a closely packed plane.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.36 no.5
• /
• pp.331-338
• /
• 2023

Modern bulletproof armor must be light and have excellent penetration resistance to ensure the mobility and safety of soldiers and military vehicles. The ballistic performance of heterogeneous structures of laminated flat plates as bulletproof armor depends on the arrangement of constituent materials for the same weight. In this study, we analyze bulletproof performance according to the stacking sequence of laminated bulletproof armor composed of Kevlar, ultra-high molecular weight polyethylene, and ethylene-vinyl-acetate foam. A ballistic analysis was performed by colliding a 7.62 × 51 mm NATO cartridge's M80 bullet at a speed of 856 m/s with six lamination arrangements with constituent materials thicknesses of 5 mm and 6.5 mm. To evaluate the bulletproof performance, the residual speed and residual energy of the projectile that penetrated the heterogeneous laminated flat plates were measured. Simulation results confirmed that the laminated structure with a stacking sequence of Kevlar, ultra-high molecular weight polyethylene, and ethylene-vinyl-acetate foam had the best bulletproof performance for the same weight.

• Ocean Systems Engineering
• /
• v.8 no.4
• /
• pp.409-426
• /
• 2018

This paper presents the strengthening of tubular joint by wrapping Carbon fiber reinforced polymer (CFRP) and glass fiber reinforced polymer (GFRP). In this study, total number of layers, stacking sequence and length of wrapping are the different parameters involved when fiber reinforced polymers (FRP) composites are used for strengthening. For this, parameters where varied and results were compared with the reference joint. The best stacking sequence was identified which has the highest value in ultimate load with lesser deflections. For determining the best stacking sequence, numerical investigation was performed on CFRP composites; length of wrapping and number of layers were fixed. Later, the studies were focused on CFRP and GFRP strengthened joint by varying the total number of layers and length of wrapping. An attempt was done to propose a parametric equation from multiple regression analysis, which can be used for CFRP strengthened joints. Hashin failure criteria was used to check the failure of composites. Results revealed that FRP was having a greater influence in the load bearing capacity of joints, and in reducing the deflections and stresses of joint under axial compressive loads. It was also seen that, CFRP was far better than GFRP in reducing the stresses and deflection.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.1
• /
• pp.201-209
• /
• 2023

Recently, fiber-reinforced composites have been widely used in various industrials fields. In this study, the mechanical behavior, especially fracture behavior, of biomimetic fiber-reinforced composites subjected to pressure loading was analyzed using finite element analysis (FEA). The fiber alignments in the biomimetic composites formed a helicoidal structure, wherein a stacking sequence involved a gradual rotation of each ply in the multi-layered laminated composites. For comparison, cross-ply composite samples with fibers arranged at 0° and 90° were prepared and analyzed. In addition, the mechanical behavior was analyzed based on combinations of the stacking sequence of carbon-fiber composites and glass-fiber composites. The FEA results showed that, when compared with the cross-ply samples, the mechanical properties of the biomimetic composites were considerably improved under pressure loading, which was applied to one side of the composites. Thus, the biomimetic helicoidal structure significantly improved the mechanical properties of the composites. Placing materials having high elasticity and strength in the outermost layers (the layer of the side on which pressure was applied and the opposite side layer) of the composites also significantly contributed to improving the mechanical properties of the composites.