• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.1300-1302
• /
• 2001

For developing a 100 kW MCFC power generation system. Several design parameters for a fuel cell stack and system analysis results by Cycle Tempo, a processing computer soft ware, were described. Approximately 170 cells are required to generate 100 kW at a current density of $125mA/cm^2$ with $6000cm^2$ cells. An overall heat balance was calculated to predict exit temperature. The 100 kW power is expected only under pressurized operation condition at 3 atm. Recycle of cathode gas by more than 50% is recommended to run the stack at $125mA/cm^2$ and 3 atm. Manifolds should be designed based on gas flow rates for the suggested operating condition. The fuel cell power generation system was designed conceptually with several choices of utilization of anode exhaust gas. Also system efficiency was calculated at various type of system and operation conditions.

• International journal of advanced smart convergence
• /
• 제9권3호
• /
• pp.253-259
• /
• 2020

Most of today's large-scale cloud systems and enterprise data centers are distributing resources to improve scalability and resource utilization. NVMe-over-Fabric protocol allows submitting NVMe commands to a remote NVMe SSD through RDMA (Remote Direct Memory Access) network. It is attracting attention recently because it is possible to construct a disaggregation storage system with low latency through the protocol. However, the current I/O stack of NVMe-over-Fabric has an inefficient structure for maintaining compatibility with the traditional I/O stack. Therefore, in this paper, we propose a new mechanism to reduce I/O latency and CPU overhead by modifying I/O path of NVMe-over-Fabric to pass through legacy block layer. According to the performance evaluation results, the proposed mechanism is able to reduce the I/O latency and CPU overhead by up to 22% and 24% compared to the existing NVMe-over-Fabrics protocol, respectively.

• 설비공학논문집
• /
• 제20권3호
• /
• pp.197-204
• /
• 2008

DMFC(Direct Methanol Fuel Cell) is one of promising candidates for power sources of small mobile IT devices like notebook, cell phone, and so on. Efficient operation of fuel cell system is very important for long-sustained power supply because of limited fuel tank size. It is necessary to investigate operation characteristics of fuel cell stack for optimal control of DMFC system. The generated voltage was modeled according to various operating condition; methanol concentration, stack temperature, and load current. It is inevitable for methanol solution at anode to cross over to cathode through MEA(membrane electrode assembly), which reduces the system efficiency and increases fuel consumption. In this study, optimal operation conditions are proposed by analyzing stack performance model, cross-over phenomenon, and system efficiency.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 추계학술대회 논문집
• /
• pp.338-338
• /
• 2015

VRFB(Vanadium Redox Flow Battery)는 바나듐계 이온을 전해질로 사용하는 레독스 흐름 전지로, 전해질의 양이 전지의 용량을 결정하기 때문에 주로 대용량의 전력이 필요한 플랜트 등에서 주로 사용하는 전지이다. 이 VRFB내에는 Current collector의 부식 방지용으로 두꺼운 Graphite판을 BP(Bipolar plate)로 사용한다. 플랜트에서는 대용량 전지를 필요로 하여 Single stack으로는 사용되기 어렵고, Multi stack으로 주로 사용한다. Multi stack의 경우, 수 백장의 BP가 들어가 전지의 부피가 매우 커지게 되고, 이에 본 연구에서는 BP의 두꺼운 Graphite를 얇은 $TiO_2$ 기판으로 교체하여 성능을 비교하는 연구를 진행하였다. Ti 금속기판을 양극산화법으로 $TiO_2$ 나노튜브 구조를 만든 후, $TiO_2$의 전도도 향상을 목적으로 $IrO_2$를 코팅하였다. 결과적으로 기존의 Graphite에 비해 전기화학적 특성이 향상되었음을 확인하였으며, Cell test를 통해 VRFB의 성능을 평가하였다.

• 한국수소및신에너지학회논문집
• /
• 제6권2호
• /
• pp.53-63
• /
• 1995

차세대의 새로운 발전방식인 용융탄산염형 연료전지 시스템개발 사업중 실용 스택개발을 위하여 전극유효연적이 $100cm^2$ 인 단위전지를 10단 적층한 Cross Flow형 MCFC스택을 제작하고 2성능측정설비를 구성하여 장기운전시험을 실시하였다 연료로는 $H_2/CO_2/H_2O$의 비율을 72%/18%/10% 로 조성한 가스를 이용하고 산화제가스로는 $O_2/CO_2$ 및 $Air/CO_2$ 비율이 33%/67%, 70%/30%가 되는 가스를 이용하여 운전할때의 초기성능 및 15A($150mA/cm^2$) 정부하 상태에서의 장기운전시험시의 전압 강하율을 조사하였다. 운전시간 310시간이 경과된 후의 스택전압은 8.39V이었고 이때의 출력은 125.8W를 보여주었다. 한편 1845시간이 경과한후 공기를 산화제로 이용하는 경우 전압은 6.95V로서 출력 104W를 나타내고 있다. 초기성능치에 의한 에너지 변환효율은 이용율이 40%인 경우 29.65%이었고 80%로 증가하는 경우 약 51.5%가 된다. 1840시간의 경과한때 까지의 전압 강하율은 약 52.4mV/1000hr로서 이전의 스택보다는 전압강하율이 감소되고 있으며 스택의 성능 저하의 주요한 요인은 개회로 전압의 저하로 내부단락동에서 기인하는 것으로 여겨진다. 또한 장기운전사 스택내부에서의 단위전지 전압분포가 균일하지 않음을 알 수 있어 이에 대한 개선을 필요로 한다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제4권3호
• /
• pp.228-239
• /
• 2004

In this paper, an analytical model accounting for the quantum effects in MOSFETs has been developed to study the behaviour of $high-{\kappa}$ dielectrics and to calculate the threshold voltage of the device considering two dielectrics gate stack. The effect of variation in gate stack thickness and permittivity on surface potential, inversion layer charge density, threshold voltage, and $I_D-V_D$ characteristics have also been studied. This work aims at presenting a relation between the physical gate dielectric thickness, dielectric constant and substrate doping concentration to achieve targeted threshold voltage, together with minimizing the effect of gate tunneling current. The results so obtained are compared with the available simulated data and the other models available in the literature and show good agreement.

• 한국가스학회지
• /
• 제11권1호
• /
• pp.51-54
• /
• 2007

78개 셀의 전극유효 면적이 $295cm^{2}$인 고분자 전해질 연료전지(PEMFC) 스택의 운전특성과 CO 피독에 대한 영향을 조사하였다. 전류밀도 $325mA/cm^{2}$에서 출력 5.4kW를 6시간 유지시키는 동안 셀들의 전압편차는 2.3%로 매우 안정함을 보였다. 개질과정의 부산물로 생성되는 CO는 PEHFC의 성능에 중요한 영향을 끼치는 스택의 주 오염물질중의 하나이다. 시간에 따른 연속적인 CO 피독 실험(5-20ppm)은 스택의 피독과 재생과정의 route를 알 수 있었다.

• Current Optics and Photonics
• /
• 제4권5호
• /
• pp.428-433
• /
• 2020

Recently, the on-chip autofocus (AF) function has become essential to the CMOS image sensor. An auto-focus usually operates using phase detection of the photocurrent difference from a pair of AF pixels that have focused or defocused. However, the phase-detection method requires a pair of AF pixels for comparison of readout. Therefore, the pixel variation may reduce AF performance. In this paper, we propose a color-selective AF pixel with a plasmonic nanostructure in a 0.9 μ㎡ pixel. The suggested AF pixel requires one pixel for AF function. The plasmonic nanostructure uses metal-insulator-metal (MIM) stack arrays instead of a color filter (CF). The color filters are formed at the subwavelength, and they transmit the specific wavelength of light according to the stack period and incident angles. For the optical analysis of the pixel, a finite-difference time-domain (FDTD) simulation was conducted. The analysis showed that the MIM stack arrays in the pixels perform as an AF pixel. As the primary metric of AF performance, the resulting AF contrasts are 1.8 for the red pixels, 1.6 for green, and 1.5 blue. Based on the simulation results, we confirmed the autofocusing performance of the MIM stack arrays.

• 한국초전도ㆍ저온공학회논문지
• /
• 제11권3호
• /
• pp.15-19
• /
• 2009

Recently, it is proposed to make striations on the YBCO coated conductor and to transpose each other as one of the solutions to decrease the perpendicular magnetization loss. For large power application using HTS, the stacked conductor packing the YBCO coated conductors should be used because single conductor is limited in flowing of demanded large current. In this paper, we research the affect of the striation and continuously transposed stacking geometry on the magnetization loss in perpendicularly exposed magnetic field. Several short samples having different number of striation and continuously transposed stack are prepared and tested in perpendicularly exposed magnetic field for the magnetization loss characteristics. The magnetization loss of striated sample was lower than sample without striation. The reduction effect on magnetization loss by the striation is obviously appeared in higher field and lower number of stack and decreased as increasing the transposed stacking number. Also, the reduction effect by transposed stack is obviously appeared in lower field at lower number of striation and isn't appeared at higher striation number and higher magnetic field.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권2호
• /
• pp.77-83
• /
• 2000

This paper deals with the design of a touch free eddy-current brake for high speed transportation systems by using 2-dimensional Finite Element Method (2-D FEM). The eddy current brake systems have to equipped with maximum braking force and deceleration at the given volume or mass, high braking force at small rate, attraction forces as small as possible and stable construction. The parameters, such as the number of pole, electric ampere-turns and slot width have influence on these braking characteristics. For the magnet to satisfy above-mentioned performance in high speed, the braking performance according to variation of the parameters are analyzed by the 2-D FEM. In addition, the magnet stack width is determined from equivalent stack width that is calculated by solution of the Field with scalar potential. From these results, the magnet of optimized configuration with maximum braking force and minimum attraction force is designed by the process of detail design.