• 한국작물학회지
• /
• 제45권5호
• /
• pp.335-338
• /
• 2000

The technology of direct-seeding in rice cultivation is an innovation mainly induced by factors in market economy and is rapidly diffused among individual farmhouses. Because the effect of technology can be affected by many factors under various farming circumstances, the impact and stability of the direct-seeding technology compared with transplanting was analyzed under various topographical regions. Yield in direct-seeding was higher in plains, although the farm size producing higher yield was quite different depending on the topographical regions. In the direct-seeding cultivation of rice, man-labor hours was reduced by about 38 percent and the reduction rate showed little difference among topographical regions. Fertilizer was used about 11 percent more but the increase rate varied from 3 to 17 percent depending on regions with higher rates in plains. Application of agricultural chemicals was also increased about 9 percent in direct-seeding, but the increase rate was as high as 12 percent in suburbs. More fertilizer and agricultural chemicals were used in direct-seeding cultivation by farmhouses implementing both direct-seeding and transplanting than by those implementing direct-seeding only. Use of more fertilizers and agricultural chemicals in direct-seeding in all regions may indicate its technical instability. Major problems causing the technical instability of direct-seeding cultivation should be solved by comprehensive research considering various farming circumstances such as topographical features rather than just a top-down style research and extension.

• 한국세라믹학회지
• /
• 제32권3호
• /
• pp.394-402
• /
• 1995

Electrical conductivity and thermoelectric power of the ferrous ferrite system of (Mg0.29-yMnyFe0.71)3-$\delta$O4 have been measured as function of the thermodynamic variables, cationic composition(y), temperature(T) and oxygen partial pressure(Po2) under thermodynamic equilibrium conditions at elevated temperatures. On the basis of the electrical properties-phase stability correlation, the stability regions of the ferrite spinel and its neighboring phases have been subsequently located in the log Po2 vs. y and log Po2 vs. 1/T planes in the ranges of 0 y 0.29, 1100 T/$^{\circ}C$ 1400 and 10-14 Po2/atm 1. The stability region, Δlog Po2(y, 1/T), of the ferrite spinel single phase widens with increasing Mn-content(y) and the boundaries of each region are linear against 1/T with negative slopes.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1996년도 춘계학술대회논문집; 부산수산대학교, 10 May 1996
• /
• pp.322-327
• /
• 1996

Dynamic stability of an axially oscillating cantilever beam is investigated in this paper. The equations of motion are derived and transformed into non-dimensional ones. The equations include harmonically oscillating parameters which originate from the motion-induced stiffness variation. Using the equations, the multiple scale perturbation method is employed to obtain a stability diagram. The stability diagram shows that relatively large unstable regions exist around the frequencies of the first bending natural frequency, twice the first bending natural frequency, and twice the second bending natural frequency. The validity of the diagram is proved by direct numerical simulations of the dynamic system.

• Structural Engineering and Mechanics
• /
• 제1권1호
• /
• pp.119-135
• /
• 1993

The paper presents a generalized optimal active control algorithm for earthquake-resistant structures. The study included the weighting matrix configuration, stability, and time-delays for achieving control effectiveness and optimum solution. The sensitivity of various time-delays in the optimal solution is investigated for which the stability regions are determined. A simplified method for reducing the influence of time-delay on dynamic response is proposed. Numerical examples illustrate that the proposed optimal control algorithm is advantageous over others currently in vogue. Its feedback control law is independent of the time increment, and its weighting matrix can be flexibly selected and adjusted at any time during the operation of the control system. The examples also show that the weighting matrix based on pole placement approach is superior to other weighting matrix configurations for its self-adjustable control effectiveness. Using the time-delay correction method can significantly reduce the influence of time-delays on both structural response and required control force.

• Structural Engineering and Mechanics
• /
• 제6권8호
• /
• pp.939-953
• /
• 1998

Vibration, buckling and dynamic stability of a cantilever rectangular plate subjected to an in-plane sinusoidally varying load applied along the free end are analyzed. The thin plate small deflection theory is used. The Rayleigh-Ritz method is employed to solve vibration and buckling of the plate. The dynamic stability problem is solved by using the Hamilton principle to drive time variables. The resulting time variables are solved by the harmonic balance method. Buckling properties and natural frequencies of the plate are shown at first. Unstable regions are presented for various loading conditions. Simple parametric resonances and combination resonances with sum type are obtained for various loading conditions, static load and damping.

• 한국소음진동공학회논문집
• /
• 제16권10호
• /
• pp.1074-1081
• /
• 2006

This paper deals with the dynamic stability analysis of clamped-hinged columns with constant volume. Numerical methods are developed for solving natural frequencies and buckling loads of such columns, subjected to an axial compressive load. The parabolic taper with the regular polygon cross-section is considered, whose material volume and column length are always held constant. Differential equations governing both free vibrations and buckled shapes of such columns are derived. The Runge-Kutta method is used to integrate the differential equations, and the Regula-Falsi method is used to determine natural frequencies and buckling loads, respectively. The numerical methods developed herein for computing natural frequencies and buckling loads are found to be efficient and robust. From the numerical results, dynamic stability regions, dynamic optimal shapes and configurations of strongest columns are reported in figures and tables.

• 소음진동
• /
• 제10권5호
• /
• pp.865-872
• /
• 2000

This paper presents the modeling, theoretical formulation, and stability analysis for a combined system of a spinning disc and a head that contacts the disc. In the analytic model, head interference is considered by a rotating mass-spring-damper system together with a frictional follower force on the damped annular discs. The multiple scale method is utilized to perform the stability system that shows the existence of instability associated with parametric resonances. Using the formulated system , instability regions of optical recording disc are investigated with variation of mass, stiffness and friction force of a head, respectively. The simulation results show that the stiffness of a head is the most sensitive parameter on the instability of the disc.

• 대한조선학회논문집
• /
• 제28권1호
• /
• pp.69-82
• /
• 1991

축방향의 주기적인 하중으로 가진되는 긴 수직보의 동적안정성에 관하여 연구하였다. 해석방법으로서 Galerkin방법을 이용하여 무한원 연립 Mathieu형 미분 방정식을 얻었으며, 안정성영역을 나타내는 도표를 얻기 위하여, 섭동법과 수치적인 방법을 사용하였다. 또한 이두가지 방법으로 구한 결과를 서로 비교 검토하였다. 여러가지 경계조건에 대한 안정영역을 구했으며, 김쇠의 영향, 평균인장력 및 다중 주파수 파라메터 기진의 영향에 관해서 집중적으로 연구하였다.

• 대한기계학회논문집
• /
• 제14권3호
• /
• pp.526-533
• /
• 1990

본 연구에서는 단일 캠 구동기구의 안정성 해석을 위한 효율적인 방법이 제시 되고, 수치실험을 통하여 검증되었다. 우선 단일 캠 구동기구를 묘사하는 비선형 방 정식이 유도되고, 동안정성에 관여하는 변수들이 무차원화되어 도입된다. 유도된 방 정식은 캠 축의 입력각에 대하여 선형화되고, 선형화된 방정식에 조화균형법(harmonic balance method)을 적용하여 동안정성 해석을 수행하였다.

• Steel and Composite Structures
• /
• 제28권1호
• /
• pp.25-37
• /
• 2018

For the first time, the parametric instability characteristics of tow-steered variable stiffness composite laminated (VSCL) cylindrical panels is investigated using B-spline finite strip method (FSM). The panel is considered containing geometrical defects including cutout and delamination. The material properties are assumed to vary along the panel axial length of any lamina according to a linear fiber-orientation variation. A uniformly distributed inplane longitudinal loading varies harmoni-cally with time is considered. The instability load frequency regions corresponding to the assumed in-plane parametric load-ing is derived using the Bolotin's first order approximation through an energy approach. In order to demonstrate the capabili-ties of the developed formulation in predicting stability behavior of the thin-walled VSCL structures, some representative results are obtained and compared with those in the literature wherever available. It is shown that the B-spline FSM is a proper tool for extracting the stability boundaries of perforated delaminated VSCL panels.