• 소성∙가공
• /
• 제24권2호
• /
• pp.95-100
• /
• 2015

It was confirmed that when phosphor slurry is formed in the cavity of an elastic mold, the pressure distribution of the phosphor slurry varies as a function of the major squeegee parameters (squeegee angle, squeegee velocity, and the viscosity of the phosphor slurry). The higher the slurry viscosity, the faster the squeegee velocity, and the smaller the squeegee angle, the higher the filling completeness of the phosphor slurry. The optimum conditions for complete filling of the phosphor slurry were found when the squeegee angle was between 30 to 45 degrees, squeegee velocity at 40 to 70mm/sec, and the viscosity of the phosphor slurry composite was at 6,556 cps (i.e. phosphor content around 50 wt. %).

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -1
• /
• pp.22-25
• /
• 2002

The Mass production of ceramic heater has encountered with the estimation for the proper parameters of the printing conditions. This paper presents a method to estimate the squeegee pressure. It uses resistance distribution from the trial run with approximate squeegee pressure which comes from statistical process control (SPC). Then, the resistance distribution and its total resistance are input to the backpropagation neural networks that can recognize resistance's distribution patterns. The value of output network derived from the input value can identify to the appropriate squeegee pressure. The experimental results are demonstrated In ensure the efficiency and the reliability of this method with the accuracy 96.75 percent. Indeed, embedded on this method will aid us to reduce the loss from the normal mass production.

• 한국생산제조학회지
• /
• 제21권1호
• /
• pp.26-32
• /
• 2012

In the present study, the stencil printing process using solder paste are numerically analyzed. The key design parameters in the stencil printing process are the printing conditions, stencil design, and solder paste properties. Among these parameters, the effects of printing conditions including the squeegee angle and squeegee pressure are investigated through finite element (FE) analysis. However, the FE analysis for the stencil printing process requires tremendous computational loads and time because this process carries micro-filling through thousands of micro-apertures in stencil. To overcome this difficulty in simulation, the present study proposes a two-step approach to sequentially perform the global domain analysis and the local domain analysis. That is, the pressure development under the squeegee are firstly calculated in the full analysis domain through the global analysis. The filling stage of the solder paste into a micro-aperture is then analyzed in the local analysis domain based on the results of the preceding global analysis.

• 한국전기전자재료학회논문지
• /
• 제33권5호
• /
• pp.355-359
• /
• 2020

In this study, image analysis and surface roughness measurements using an optical microscope are presented as a method to quantitatively evaluate the results of screen printing. Using this method, the squeegee speed, which is the printing process condition, and the printability of the electrode according to the screen mesh were evaluated. Increasing the squeegee speed in the printing process acts as a process element that increases the line width precision of the printed electrode and lowers the surface roughness of the printed surface. Furthermore, the edge roughness, which indicates the clarity of printing, was not significantly affected by the speed of the squeegee during printing. The print thickness increases in proportion to the squeegee speed, but is largely dependent on the screen thickness.

• 마이크로전자및패키징학회지
• /
• 제18권4호
• /
• pp.71-77
• /
• 2011

표면실장형 수동소자인 0402, 0603, 1005 칩에 대한 인쇄 주요인자 결정 및 공정 최적화를 실험계획법을 통해 실시하였다. 실험에 사용된 솔더는 Sn-3.0Ag-0.5Cu와 Sn-0.7Cu이며, 공정변수로는 스텐실 두께, 스퀴지 각도, 인쇄 속도, 기판분리 속도, 스텐실과 기판간의 갭이며, 인쇄압력은 2 $kgf/cm^2$로 고정하였다. 분산분석을 통해 인쇄효율에 영향을 미치는 주요인자가 스텐실 두께와 스퀴지 각도임을 확인할 수 있었다. 주요인자인 스텐실 두께와 스퀴지 각도를 변화시켜 인쇄효율의 최적화 영역을 확인하였고, 0402, 0603, 1005 칩 모두 스퀴지 각도가 $45^{\circ}$ 이하일 경우 인쇄효율이 높았다. 스텐실 두께를 변화할 경우 칩 크기에 따라 인쇄효율이 다른 양상을 보였는데, 0402, 0603 칩에서는 스텐실 두께가 얇을수록 높은 인쇄효율을 보였으며, 1005 칩에서는 스텐실 두께가 두꺼울수록 높은 인쇄효율을 나타내었다.

• 반도체디스플레이기술학회지
• /
• 제11권1호
• /
• pp.73-78
• /
• 2012

In this study, the optimal process condition was induced about the pillar arrangement process of applying the screen printing method in the manufacture process of vacuum glazing panel. The high precision screen printing is technology which pushes out the paste and spreads it by using the squeegee on the stainless steel plate in which the pattern is formed. The screen printing method is much used in the flat panel display field including the LCD, PDP, FED, organic EL, and etc for forming the high precision micro-pattern. Also a number of studies of screen printing method have been conducted as the method for the cost down through the improvement of productivity. The screen printing method has many parameters. So we used Taguchi method in order to decrease test frequencies and optimize this parameters efficiently. In this study, experiments of pillar arrangement were performed by using Taguchi experimental design. We analyzed experimental results and obtained optimal conditions which are 4 m/s of squeegee speed, $40^{\circ}$ of squeegee angle and distance between metal mask and glass.

• 한국인쇄학회지
• /
• 제20권2호
• /
• pp.19-30
• /
• 2002

Four screen mesh counts of 100, 150, 200, and 305 threads per inch are chosen and a designed test figure is exposed on them for printing experiment to measure the ink deposit thickness. Among a number of variables, the ink viscosity, the screen gap and the squeegee pressure and speed are estimated with their effected thickness. These variables affect as much as around 50% compared with the theoretical ink volume listed by the mesh manufacturer and each variable has different influence on the thickness. The data and graphs have been analyzed for the thick film production.

• 한국생산제조학회지
• /
• 제5권4호
• /
• pp.18-25
• /
• 1996

In this study, we have developed the stereolithography system that supports the development of a products. This paper presents the development of the stereolithography system. The system is composed of hardware, software and control part. The software converts a STL file to NC data and displays the monitoring figure in control part. The hardware part deals with structure of machine. The most important theme in this paper is LG-SLCAM software. This software can generate NC data and scanning condition data from a STL file semiautimatically. On the basis of three diensional shapes, it makes data for support structure from STL file. The effectiveness of using out stereolithography system is confirmed by processes of good development.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2007년도 추계학술발표논문집
• /
• pp.140-143
• /
• 2007

본 연구의 목적은 반도체 후공정 제조 시스템인 Screen Printer시스템에서의 프린팅 공정시 프린팅에 사용되는 Mesh Mask, Urethane Blade의 재질이 사용되는 반복횟수의 증가에 따라 재질의 변화에 의한 문제점과 프린팅 공정 파라미터인 Table 접촉거리, Squeegee 하강위치의 주변환경에 의한 변화를 보상하여 일정하게 프린팅이 될 수 있는 시스템을 구현 하는데 목적이 있으며, 이 논문은 서보모터를 구동하는 위치제어 시스템에 로드셀（Loadcell）을 이용하는 압력제어시스템을 연구하고 구현하고자 하였다.

• 한국전기전자재료학회논문지
• /
• 제27권4호
• /
• pp.209-216
• /
• 2014

The screen printed technique is one of the electrode forming technologies for crystalline silicon solar cell. It has the advantage that can raise the production efficiency due to simple process. The electrode technology is the core process because the electrode feature is given a substantial factor (for solar cell efficiency). In this paper, we tried to change conditions such as squeegee angle $55{\sim}75^{\circ}$, snap off 0.5~1.75 mm, printing pressure 0.6~0.3 MPa and 1.6~2.0 mm finger spacing. As a result, the screen printing process showed an improved performance with an increased height higher finger height. Optimization of fabrication process has achieved 17.48% efficiency at screen mesh of 1.6 mm finger spacing.