• Geotechnical Engineering
• /
• v.4 no.4
• /
• pp.29-38
• /
• 1988

One of the main objectives of researches for the chemical grouting is to assess the changes in soil properties caused by injection of chemical grout. Especially the changes in the strength properties of soils, such as elastic modulus, shear modulus of ground due to injection of chemical grout has drawn our attention. Since the specific surface changes with variation in the grain size of sandy soil, the influence of grain size of sandy toil on the strength and stiffness of silicate-grouted soil was investicated in this study by earring out uniaxial and triaxial compression tests. It was found that the strength and stiffness of grouted soil increased as the grain size of sandy soil decreases, the possibility of estimating the strength of grouted soil was confirmed through the study of relationship between specific surface of sandy soil and the strength of chemical gel.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.4
• /
• pp.57-68
• /
• 2014

This study categorizes the distributed sand around coastal area of Jeju volcanic Island into three groups according to their components, and arranges their characteristics. In the case of basic physical properties, the silicate sand has slightly greater specific gravity than general sand, and the carbonate sand with widespread distribution has a lower specific gravity. In the gross, the carbonate sand has poor particle classifying and low uniformity coefficient because carbonate minerals of relatively large grain size are mixed. The relation between compressive strength and components shows conflicting tendency that silicate and carbonate components have positive correlation and negative correlation with compressive strength, respectively. Based on the components ratio of one to one, the sand having low carbonate component ratio is expected to be able to utilize in construction fine aggregate. To compare between square root (ACI 308) and cube root (KCI 2012) of compressive strength at computation of elastic modulus, it is considered to non-dimensional elastic modulus.

• The Journal of Engineering Geology
• /
• v.18 no.4
• /
• pp.371-379
• /
• 2008

In this study, seismic elastic wave and dynamic elastic modulus properties are investigated by down-hole seismic tests that were applied to the 11 gneiss area. The research results show that the realtionship between the two properties are $V_s=0.5589{\times}V_p$ in gneiss. The relationship between the two properties are separated into two groups. Group 1 is influenced mainly by the specific gravity of rock, but group 2 is influenced mainly by the joint aperture. As weathering progresses, group 1 clearly shows a decreasing tendency. In fresh and slightly weathered rock-mass, correlations between $V_p$ and dynamic elastic modulus is expressed in linear line but in moderately-highly weathered rock-mass, correlations between $V_p$ and dynamic elastic modulus is expressed curve as a quadratic function. Correlations between $V_s$ and dynamic elastic modulus are analyzed similar with a $V_p$ case.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.111-115
• /
• 2005

Recently, natural fibers draw much interests in composite industry due to low cost, light weight, and environment-friendly characteristics compared with glass fibers. In this study, mechanical properties were evaluated for two extreme cases of jute fiber orientations, i.e. the unidirectional yarn composites and the felt fabric composites. Samples of jute fiber composites were fabricated by RTM process using epoxy resin, and tensile, compression, and shear tests were conducted. As can be expected, unidirectional fiber specimens in longitudinal direction showed the highest strength and modulus. Compared with glass/epoxy composites of the similar fabric architecture and fiber volume fraction, the tensile strength and modulus of jute felt/epoxy composites reached only 40% and 50% levels. However, the specific tensile strength and modulus increased to 80% and 90% of the glass/epoxy composites. The main reason for the poor mechanical properties of jute composites is associated with the weak interfacial bonding between fiber and matrix. The effect of surface treatment of jute fibers on the interfacial bonding will be examined in the future work.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.2
• /
• pp.274-282
• /
• 2016

This aims of this study were to investigate the relationship between non-destructive evaluation (NDE) and actual bending properties of particleboard, and to predict the bending properties of three-layer particleboard. Three kinds of raw materials, i.e. Hinoki (Chamaecyparis obtusa Endl.) strand, knife-milled Douglas-fir (Pseudotsuga manziesii (Mirb) Franco), and hammer-milled matoa (Pometia spp.) obtained from wooden industry, were utilized as furnish for experimental panel with methylene diphenyl diisocyanate (MDI) resin as binder. The NDE test was conducted by hit sounds using an FFT analyzer according to the spectrum peak of wave frequency, while the static bending test was conducted according to JIS A-5908. The results reveal that the dynamic Young's modulus as an NDE test has a potential for being used to predict the elastic bending of particleboards by a specific equation for adjusting its proper values. The values of NDE and static test are significantly different with a deviation range at 3-20%. The bending stiffness of three-layer particleboards manufactured from different wood species is predictable by observing the bending stiffness of two elements based on the thickness of its layers. The predicted values of bending stiffness and static test are significantly different with a deviation range at 5-24%.

• Steel and Composite Structures
• /
• v.7 no.1
• /
• pp.19-34
• /
• 2007

This paper presents results of a non-linear finite element analysis of axially loaded slender hollow structural section (HSS) columns, strengthened using high modulus carbon-fiber reinforced polymer (CFRP) longitudinal sheets. The model was developed and verified against both experimental and other analytical models. Both geometric and material nonlinearities, which are attributed to the column's initial imperfection and plasticity of steel, respectively, are accounted for. Residual stresses have also been modeled. The axial strength in the experimental study was found to be highly dependent on the column's imperfection. Consequently, no specific correlation was established experimentally between strength gain and amount of CFRP. The model predicted the ultimate loads and failure modes quite reasonably and was used to isolate the effects of CFRP strengthening from the columns' imperfections. It was then used in a parametric study to examine columns of different slenderness ratios, imperfections, number of CFRP layers, and level of residual stresses. The study demonstrated the effectiveness of high modulus CFRP in increasing stiffness and strength of slender columns. While the columns' imperfections affect their actual strengths before and after strengthening,the percentage gain in strength is highly dependent on slenderness ratio and CFRP reinforcement ratio, rather than the value of imperfection.

• Tunnel and Underground Space
• /
• v.23 no.3
• /
• pp.212-218
• /
• 2013

Tuff specimens were thermally treated with predetermined temperatures of 200, 400 and $600^{\circ}C$ to construct specimens simulating weathered tuff rocks. Specific gravity, absorption ratio, elastic wave velocity, uniaxial compressive strength, Brazilian tensile strength, Young's modulus, Poisson's ratio and slake-durability index were measured for pre-heated specimens. Heating of rock specimens entailed the degradation of material properties except for slake-durability index. It was found that correlations among P-wave velocity, uniaxial compressive strength, Brazilian tensile strength, Young's modulus and absorption ratio are high. Regression equations which use the P-wave velocity as an independent variable were presented to evaluate uniaxial compressive strength, Brazilian tensile strength, Young's modulus and absorption ratio.

• Journal of the Korean Society of Safety
• /
• v.37 no.4
• /
• pp.11-19
• /
• 2022

This paper presents the effects of high temperature and water absorption on the mechanical behaviors of carbon-aramid fiber composites, specifically their strength, elastic modulus, and fracture. These composites are used in industrial structures because of their high specific strength and toughness. Carbon fiber composites are vulnerable to the impact force of external objects despite their excellent properties. Aramid fibers have high elongation and impact absorption capabilities. Accordingly, a hybrid composite with the complementary properties and capabilities of carbon and aramid fibers is fabricated. However, the exposure of aramid fiber to water or heat typically deteriorates its mechanical properties. In view of this, tensile and flexural tests were conducted on a twill woven carbon-aramid fiber hybrid composite to investigate the effects of high temperature and water absorption. Moreover, a multiscale analysis of the stress behavior of the composite's microstructure was implemented. The results show that the elastic modulus of composites subjected to high temperature and water absorption treatments decreased by approximately 22% and 34%, respectively, compared with that of the composite under normal conditions. The crack behavior of the composites was well identified under the specimen conditions.

• Computers and Concrete
• /
• v.20 no.2
• /
• pp.177-184
• /
• 2017

The characteristics of lightweight aggregate (LWA) with a low specific gravity and high water absorption will significantly change the properties of lightweight aggregate concrete (LWAC). This study aimed at exploring the effect of presoaking degree of LWA on the strength degeneracy of LWAC and flexural behavior of LWAC members exposed to elevated temperatures. The residual mechanical properties of the LWAC subjected to elevated temperatures were first conducted. Then, the residual load tests of LWAC members (beams and slabs) after exposure to elevated temperatures were carried out. The test results showed that with increasing temperature, the decreasing trend of elastic modulus for LWAC was considerably more serious than the compressive strength. Besides, the presoaking degree of LWA had a significant influence on the residual compressive strength and elastic modulus for LWAC after exposure to $800^{\circ}C$. Moreover, owing to different types of heating, the residual load bearing capacity of the slab specimens were significantly different from those of the beam specimens.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.3
• /
• pp.44-51
• /
• 2004

The effect of refining conditions and grammage on the stiffness of linerboard was investigated. The correlations between Taber stiffness and resonance stiffness were very low due to the different measuring principle. The refining conditions did not affect sig nificantly on both Taber and resonance stiffness estimated here. This means that it is strongly recommended to find and apply the refining conditions which can reduce specific energy consumption. Taber stiffness showed very high correlation for the thickness and elastic modulus of linerboard, while the resonance stiffness showed much lower correlation. Effective thicknesses for Taber stiffness were very well fitted with measured thickness, while those for resonance stiffness depended on the grammage of linerboard.