• Journal of Powder Materials
• /
• v.22 no.3
• /
• pp.163-168
• /
• 2015

Ti alloys are extensively used in high-technology application because of their strength, oxidation resistance at high temperature. However, Ti alloys tend to be classified very difficult to cut material. In this paper, The powder synthesis, spark plasma sintering (SPS), bulk material properties such as electrical conductivity and thermal conductivity are systematically examined on $Ti_2AlN$ and $Ti_2AlC$ materials having most light-weight and oxidation resistance among the MAX phases. The bulk samples mainly consisted of $Ti_2AlN$ and $Ti_2AlC$ materials with density close to theoretical value were synthesized by a SPS method. Machining characteristics such as machining time, surface quality are analyzed with measurement of voltage and current waveform according to machining condition of micro-electrical discharge machining with micro-channel shape.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.10
• /
• pp.665-670
• /
• 2016

Prevailing dissemination of machine tools and cutting technology have caused drastic developments of high speed dry machining with work materials of high hardness, and demands on the high-hardness-materials with high efficiency have become increasingly important in terms of productivity, cost reduction, as well as environment-friendly issue. Addition of Si to TiAlN has been known to form nano-composite coating with higher hardness of over 30 GPa and oxidation temperature over $1,000^{\circ}C$. However, it is not easy to add Si to TiAlN by using conventional PVD technologies. Therefore, Ti-Al-Si-N have been prepared by hybrid process of PVD with multiple target sources or PVD combined with PECVD of Si source gas. In this study, a single composite target of Ti-Al-Si was prepared by powder metallurgy of MA (mechanical alloying) and SPS (spark plasma sintering). Properties of he resulting alloying targets were examined. They revealed a microstructure with micro-sized grain of about $1{\sim}5{\mu}m$, and all the elements were distributed homogeneously in the alloying target. Hardness of the Ti-Al-Si-N target was about 1,127 Hv. Thin films of Ti-Al-Si-N were prepared by unbalanced magnetron sputtering method by using the home-made Ti-Al-Si alloying target. Composition of the resulting thin film of Ti-Al-Si-N was almost the same with that of the target. The thin film of Ti-Al-Si-N showed a hardness of 35 GPa and friction coefficient of 0.66.

• Composites Research
• /
• v.19 no.2
• /
• pp.28-34
• /
• 2006

[ $Cu-TiB_2$ ] metal matrix composites with various weight fractions of $TiB_2$ were fabricated by combination of manufacturing process, SPS (self-propagating high-temperature synthesis) and SPS (spark plasma sintering). The feasibility of $Cu-TiB_2$ composites for welding electrodes and sliding contact material was investigated through experiments on the tensile properties, hardness and wear resistance. To obtain desired properties of composites, composites are designed according to reinforcement's shape, size and volume fraction. Thus proper modeling is essential to predict the effective material properties. The elastic moduli of composites obtained by FEM and tensile test were compared with effective properties from the original Eshelby model, Eshelby model with Mori-Tanaka theory and rule-of-mixture. FEM result showed almost the same value as the experimental modulus and it was found that Eshelby model with Mori-Tanaka theory predicted effective modulus the best among the models.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.127.1-127.1
• /
• 2010

고체산화물연료전지는 고효율 및 무공해의 전기화학 에너지 변환장치로서, 최근 국내외에서 활발한 연구개발이 수행되고 있다. 특히, 고체산화물 연료전지 시스템의 조기 상용화를 위해 시스템의 작동온도를 약 $800^{\circ}C$ 이하로 낮추고 저가로 생산 할 수 있는 제조공정 개발에 대한 연구를 적극적으로 수행하고 있다. 본 연구에서는 고체산화물연료전지의 단위셀를 구성하는 연료극지지체 및 박막 전해질에 대해서 저가 양산의 테이프케스팅법 및 동시소성 공정, 그리고 연료극 지지체 전해질(anode-supported electrolyte)에 대한 공기극 페이스트 프린팅 제조공정에 대해 소개한다. 또한 고체산 화물연료전지의 제조공정 및 시간을 단축하기 위해 방전플라즈마 소결공법(SPS)에 의한 연료극 지지체 제조 공정, 단위셀의 성능 최적화를 위한 나노 스케일의 고성능 전해질 소재 분말합성 공정(crystallite size: 5~10nm, surface area : $100m^2/g$ 이상) 그리고 테이프케스팅에 의한 박막 전해질 제조 공정(thin film : $10{\mu}m$ 이하) 등 주요 단위셀 소재 및 부품의 제조공정 특성 그리고 단위셀의 전기화학적 특성(max. power density : 1.0 W/$cm^2$)에 대해 소개하며, 최종적으로 평판형 대면적 고체산화물연료전지(max. $20cm{\times}15cm$)의 단위셀 상용화 제조 기술 및 성능평가 기술에 대해서도 소개 할 예정이다.

• Journal of Powder Materials
• /
• v.16 no.5
• /
• pp.316-325
• /
• 2009

Fe based (Fe$_{68.2}$C$_{5.9}$Si$_{3.5}$B$_{6.7}$P$_{9.6}$Cr$_{2.1}$Mo$_{2.0}$Al$_{2.0}$) amorphous powder, which is a composition of iron blast cast slag, were produced by a gas atomization process, and sequently mixed with ductile Cu powder by a mechanical ball milling process. The experiment results show that the as-prepared Fe amorphous powders less than 90 $\mu$m in size has a fully amorphous phase and its weight fraction was about 73.7%. The as-atomized amorphous Fe powders had a complete spherical shape with very clean surface. Differential scanning calorimetric results of the as-atomized Fe powders less than 90 $\mu$m showed that the glass transition, T$_g$, onset crystallization, T$_x$, and super-cooled liquid range $\Delta$T=T$_x$-T$_g$ were 512, 548 and 36$^{\circ}C$, respectively. Fe amorphous powders were mixed and deformed well with 10 wt.% Cu by using AGO-2 high energy ball mill under 500 rpm.

• Journal of Powder Materials
• /
• v.15 no.1
• /
• pp.23-30
• /
• 2008

Ni-20Cr-20Fe-5Nb alloy with or without $Y_2O_3$ was manufactured by mechanical alloying process and consolidated by spark plasma sintering (SPS). The grain size of the alloy with $Y_2O_3$ was smaller than that of alloy without $Y_2O_3$ which results from the effect of $Y_2O_3$ suppressing grain growth. The tensile strength at room temperature was increased by the addition of $Y_2O_3$ but decreased abruptly at temperature above $600^{\circ}C$. It seems to result from the change of deformation mechanism due to fine grain size, that is, grain boundary sliding is predominant at above $600^{\circ}C$ while internal dislocation movement is predominant at below $600^{\circ}C$. After conventional heat treatment process of solution treatment and aging, a small amount of ${\delta}(Ni_3Nb)$ phase was formed in Ni-20Cr-20Fe-5Nb alloy while a large amount of ${\gamma}"(Ni_3Nb)$ was formed in Inconel 718 in the previous report. This is due to exhaustion of Nb content by the formation of NbC during consolidation.

• Journal of the Korean Ceramic Society
• /
• v.51 no.1
• /
• pp.43-50
• /
• 2014

We fabricated undoped and Sb-doped $SnO_2$ thin films on glass substrates by a pulsed laser deposition (PLD) process. Undoped and 2 - 8 wt% $Sb_2O_3$-doped $SnO_2$ targets with a high density level of ~90% were prepared by the spark plasma sintering (SPS) process. Initially, the effects of the deposition temperature on undoped $SnO_2$ thin films were investigated in the region of $100-600^{\circ}C$. While the undoped $SnO_2$ film exhibited the lowest resistivity of $1.20{\times}10^{-2}{\Omega}{\cdot}cm$ at $200^{\circ}C$ due to the highest carrier concentration generated by the oxygen vacancies, 2 wt% Sb-doped $SnO_2$ film exhibited the lowest resistivity value of $5.43{\times}10^{-3}{\Omega}{\cdot}cm$, the highest average transmittance of 85.8%, and the highest figure of merit of 1202 ${\Omega}^{-1}{\cdot}cm^{-1}$ at $400^{\circ}C$ among all of the doped films. These results imply that 2 wt% $Sb_2O_3$ is an optimum doping content close to the solubility limit of $Sb^{5+}$ substitution for the $Sb^{4+}$ sites of $SnO_2$.

• Journal of Powder Materials
• /
• v.22 no.4
• /
• pp.254-259
• /
• 2015

$Bi_2Te_3$ related compounds show the best thermoelectric properties at room temperature. However, n-type $Bi_2Te_{2.7}Se_{0.3}$ showed no improvement on ZT values. To improve the thermolectric propterties of n-type $Bi_2Te_{2.7}Se_{0.3}$, this research has Cu-doped n-type powder. This study focused on effects of Cu-doping method on the thermoelectric properties of n-type materials, and evaluated the comparison between the Cu chemical and mechanical doping. The synthesized powder was manufactured by the spark plasma sintering(SPS). The thermoelectric properties of the sintered body were evaluated by measuring their Seebeck coefficient, electrical resistivity, thermal conductivity, and hall coefficient. An introduction of a small amount of Cu reduced the thermal conductivity and improved the electrical properties with Seebeck coefficient. The authors provided the optimal concentration of $Cu_{0.1}Bi_{1.99}Se_{0.3}Te_{2.7}$. A figure of merit (ZT) value of 1.22 was obtained for $Cu_{0.1}Bi_{1.9}Se_{0.3}Te_{2.7}$ at 373K by Cu chemical doping, which was obviously higher than those of $Cu_{0.1}Bi_{1.9}Se_{0.3}Te_{2.7}$ at 373K by Cu mechanical doping (ZT=0.56) and Cu-free $Bi_2Se_{0.3}Te_{2.7}$ (ZT=0.51).

• Journal of Powder Materials
• /
• v.17 no.4
• /
• pp.319-325
• /
• 2010

Electrical discharge machining (EDM) is an attractive machining technique but it requires electrically conductive ceramic materials. In this study, Alumina matrix composites reinforced with CNTs were fabricated through CNT purification, mixing, compaction and spark plasma sintering (SPS) processes. $Al_2O_3$ nanocomposites with the different CNT concentrations were synthesized. The mechanical and electrical characteristics of $Al_2O_3$/CNTs composites were examined in order to apply the materials to the EDM process. In addition, micro-EDM using wire electrical discharge grinding (WEDG) was conducted under the various EDM parameters to investigate the machining characteristics of machined hole by Field Emission Scanning Electron Microscope (FE-SEM). The results show that $Al_2O_3$/CNTs 10%Vol. was more suitable than the other materials because high conductivity and large discharge energy caused violent sparks resulting in bad machining accuracy and surface quality.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.259-259
• /
• 2012

Mo-Cu 합금은 열전도도, 전기전도도가 우수하고 합금조성에 따라 열팽창계수의 조절이 가능하여 반도체소재, 방열소재, 접점소재 등에 적용가능성이 높은 재료로 주목받고 있다. 또한 상태도 상에서 고용도가 전혀 없기 때문에 박막을 제작하였을 경우, 나노 복합체 형성이 용이하고 질소 분위기에서는 MoN-Cu로 상분리가 가능하여 하드상과 소프트상의 물성을 동시에 보유한 박막 제작이 가능하다. 또한 고온에서 산화반응에 의해 생기는 $MoO_3$, $CuO_3$와 같은 준안정상의 산화물들은 육방정계 구조(HCP)를 가지며 전단특성이 우수하여 자동차 저마찰 코팅재료로써 많은 연구가 진행되고 있다. 반면, Mo-Cu 는 상호간에 고상은 물론 액상에서도 고용도가 전혀 없기 때문에 일반적인 방법으로는 합금화 또는 복합화가 어렵다. 또한 Mo-Cu 박막을 제작할 경우 복수의 타겟을 이용해야 하기 때문에 성분조절과 구조적 제어가 불리하고 공정의 복잡화라는 단점을 가지고 있으며 추가적으로 다른 원소를 첨가하여 3원계, 4원계 이상의 박막을 형성하는 것에 한계가 있다. 따라서 본 연구에서는 위와 같은 문제점을 해결하기 위하여 상호간의 고용도가 없는 재료의 합금화가 용이한 기계적 합금화법(Mechanical Alloying)을 이용하여 Mo-Cu 합금분말을 제조하였고, 준안정상태의 구조의 유지가 가능한 방전 플라즈마 소결법(Spark Plasma Sintering)을 이용하여 합금타겟을 제작하였다. Mo-Cu 박막은 제작된 합금타겟을 사용하여 DC 스퍼터링 공정으로 제작하였다. Mo-Cu 박막의 공정조건으로는 타겟조성, 공정분위기, 가스 비율로 정하여 실험을 진행하였다. 제작된 박막은 자동차 코팅재료로써의 적용가능성을 보기 위해서 내열성, 내식성, 내마모성의 특성을 평가하였다.