• 전기화학회지
• /
• 제22권3호
• /
• pp.87-103
• /
• 2019

현재 상용화되어 있는 리튬이온전지에 사용하고 있는 비수계 유기 전해액은 가연성, 부식성, 고휘발성, 열적 불안정성 등의 단점 때문에 더욱 안전하고 장수명을 보이는 고체 전해질로 대체하는 연구가 진행되고 있으며, 이것은 전기자동차 및 에너지저장 시스템과 같은 중대형 이차전지에도 효율적으로 활용될 수 있다. 다양한 형태의 고체 전해질 중에서 현재 고분자 매트릭스에 활성 무기 충진재가 포함되어 있는 복합 고체 전해질이 고이온전도도와 전극과의 탁월한 계면접촉을 이루는데 가장 유리한 것으로 알려졌다. 본 총설에서는 우선 고체 전해질의 종류와 연혁에 관해 간단히 소개하고, 고분자 및 무기 충진재 (불활성 및 활성)로 구성되는 고체 고분자 전해질 및 무기 고체 전해질의 기본적 물성 및 전기화학적 특성을 개괄한다. 또한 이 소재들의 형상을 기준으로 입자형 (0D), 섬유형 (1D), 평판형 (2D), 입체형 (3D)의 형식으로 구성된 복합고체 전해질과 이에 따른 전고체 전지의 전기화학적 특성을 논의한다. 특히 리튬금속 음전극을 사용하는 전고체 전지에 있어서 양전극-전해질 계면, 음전극-전해질 계면, 입자간 계면의 특성에 관해 소개하고, 마지막으로 현재까지 보고된 관련 총설들을 참조하여 복합 고체 전해질 기술의 현재 요구조건 및 미래 전망을 알아본다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.129.2-129.2
• /
• 2010

AEM which were used for solid alkaline fuel cell(SAFC) were prepared by photo polymerization in method pore-filling with various quaternary ammonium cationic monomers and crosslinkers without an amination process. Their specific thermal and chemical properties were characterized through various analyses and the physico-chemical properties of the prepared electrolyte membranes such as swelling behavior, ion exchange capacity and ionic conductivity were also investigated in correlation with the electrolyte composition. The polymer electrolyte membranes prepared in this study have a very wide hydroxyl ion conductivity range of 0.01 - 0.45S/cm depending on the composition ratio of the electrolyte monomer and crosslinking agent used for polymerization. However, the hydroxyl ion conductivity of the membranes was relatively higher at the whole cases than those of commercial products such as A201 membrane of Tokuyama. These pore-filling membranes have also excellent properties such as smaller dimensional affects when swollen in solvents, higher mechanical strength, lowest electrolyte crossover through the membranes, and easier preparation process compared of traditional cast membranes. The prepared membranes were then applied to solid alkaline fuel cell and it was found comparable fuel cell performance to A201 membrane of Tokuyama.

• Journal of Electrochemical Science and Technology
• /
• 제13권2호
• /
• pp.199-207
• /
• 2022

Lithium-sulfur batteries (LSBs) have emerged as a promising alternative to lithium-ion batteries (LIBs) owing to their high energy density and economic viability. In addition, all-solid-state LSBs, which use solid-state electrolytes, have been proposed to overcome the polysulfide shuttle effect while improving safety. However, the high interfacial resistance and poor ionic conductivity exhibited by the electrode and solid-state electrolytes, respectively, are significant challenges in the development of these LSBs. Herein, we apply a poly (ethylene oxide) (PEO)-based composite solid-state electrolyte with oxide Li₇La₃Zr₂O₁₂ (LLZO) solid-state electrolyte in an all-solid-state LSB to overcome these challenges. We use an electrochemical method to evaluate the degradation of the all-solid-state LSB in accordance with the carbon content and loading weight within the cathode. The all-solid-state LSB, with sulfur-carbon content in a ratio of 3:3, exhibited a high initial discharge capacity (1386 mAh g^-1), poor C-rate performance, and capacity retention of less than 50%. The all-solid-state LSB with a high loading weight exhibited a poor overall electrochemical performance. The factors influencing the electrochemical performance degradation were revealed through systematic analysis.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권4호
• /
• pp.487-494
• /
• 1995

The purpose of this study is to research and develop solid polymer electrolyte(SPE) for Li secondary battery. We investigated the effects of lithium salts, plasticizer addition, temperature dependence of conductivity and electrochemical stability window of polyethylene oxide(PEO) electrolytes. PEO electrolyte completed with LiCIO$\_$4/ shows the better conductivity than the others. PEO-LiCIO$\_$4/ electrolyte, when EO/Li$\^$+/ ratio is 8, showed adequate conductivity around room temperature. By adding propylene carbonate and ethylene carbonate to PEO-LiCIO$\_$4/ electrolyte, its conductivity was higher than that of PEO-LiCIO$\_$4/ without those. Also PEO$\_$8/LiCIO$\_$4/ electrolyte remains stable up to 4.5V vs. Li/Li.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.67-68
• /
• 2006

Solid polymer electrolyte is very important in the applications to high energy density lithium batteries of high safety. In this work, solid polymer electrolytes based on PE non-woven matrix, hybrid salt, and anion receptor were successfully prepared. They could provide high ion conduction phase with maintaining mechanical strength. They also showed high electrochemical stability and lithium ion transference number. This new type of solid polymer electrolyte is expected to be a good candidate for rechargeable solid state lithium secondary batteries.

• 한국표면공학회지
• /
• 제50권4호
• /
• pp.237-243
• /
• 2017

We demonstrated the thin film deposition of sodium phosphorous oxynitride (NaPON) via RF magnetron sputtering of $Na_3PO_4$, as a solid-state Na-ion conductor similar to lithium phosphorous oxynitride (LiPON), which is a commonly used solid electrolyte. The deposited NaPON thin film was characterized by scanning electron microscopy, X-ray diffractometry, and electrochemical impedance spectroscopy, to investigate the feasibility of the solid-state electrolyte in several different cell configurations. The key properties of a solidstate electrolyte, i.e., ionic conductivity and activation energy, were estimated from the complex non-linear least square fitting of the measured impedance spectra at various temperatures in the range of $27-90^{\circ}C$. The ionic conductivity of the NaPON film was measured to be $8.73{\times}10^{-6}S\;cm^{-1}$ at $27^{\circ}C$, which was comparable to that of the LiPON film. The activation energy was estimated to be 0.164 eV, which was lower than that of the LiPON film (0.672 eV). The obtained values encourage the use of a NaPON thin film in the future as a reasonable solid-state electrolyte.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.295-298
• /
• 2009

Oxygen ionic conductors of CeScSZ electrolyte in SOFC unit cell are applied to anode and cathode as well as electrolyte to have the triple-phase-boundaries of electrochemical reaction, and it is required to decrease the sintering temperature of anode-supported electrolyte by the nanoscale of CeScSZ electrolyte powder. In this report, nanoscale CeScSZ electrolyte powder was synthesized by chemical synthesis method. The particle size, surface area and morphology of the powder were observed by SEM and BET. Thin film electrolyte of under $10{\mu}m$ was fabricated by tape casting using the synthesized CeScSZ electrolyte powder, and ionic conductivity and gas permeability of electrolyte film were evaluated. Finally the SOFC unit cell was fabricated using the anode-supported electrolyte prepared by a tape casting method and co-sintering, in which the active layer, measuring $20{\mu}m$, was introduced in the anode layer to provide a more efficient reaction. Electrochemical evaluations of the SOFC unit cell, including measurements such as power density and impedance, were performed and analyzed.

• 한국전기전자재료학회논문지
• /
• 제30권7호
• /
• pp.447-453
• /
• 2017

In this study, $Li_2MnSiO_4$ cathode material and LiPON solid electrolyte were manufactured into thin films, and the possibility of their use in thin-film batteries was researched. When the RTP treatment was performed after $Li_2MnSiO_4$ cathode thin-film deposition on the SUS substrate by a sputtering method, a ${\beta}-Li_2MnSiO_4$ cathode thin film was successfully manufactured. The LiPON solid electrolyte was prepared by a reactive sputtering method using a $Li_3PO_4$ target and $N_2$ gas, and a homogeneous and flat thin film was deposited on a $Li_2MnSiO_4$ cathode thin film. In order to evaluate the electrochemical properties of the $Li_2MnSiO_4$ cathode thin films, coin cells using only a liquid electrolyte were prepared and the charge/discharge test was conducted. As a result, the amorphous thin film of RTP treated at $600^{\circ}C$ showed the highest initial discharge capacity of about $60{\mu}Ah/cm^2$. In cases of coin cells using liquid/solid double electrolyte, the discharge capacities of the $Li_2MnSiO_4$ cathode thin films were comparable to those without solid LiPON electrolyte. It was revealed that $Li_2MnSiO_4$ cathode thin films with LiPON solid electrolyte were applicable in thin film batteries.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.169-169
• /
• 2017

Due to key roles for the electrochemical stability and charge capacity the solid-electrolyte interphase (SEI) has been extensively studied in anodes of a Li-ion battery cell. There is, however, few of investigation for cathodes. Using first-principles based calculations we describe atomic-level process of the SEI layer formation at the interface of a carbonate electrolyte and $LiMn_2O_4$ spinel cathode. Furthermore, using beyond the conventional density functional theory (DFT+U) calculations we examine the work function of the cathode and frontier orbitals of the electrolyte. Based on the results we propose that proton transfer at the interface is an essential mechanism initiating the SEI layer formation in the $LiMn_2O_4$. Our results can guide a design concept for stable and high capacity Li-ion battery cell through screening an optimum electrolyte fine-tuned energy band alignment for a given cathode.

• 한국환경보건학회지
• /
• 제40권2호
• /
• pp.137-146
• /
• 2014

Objectives: Feasibility of electrochemical oxidation of the aqueous non-biodegradable wastewater such as cationic dye Rhodamine B (RhB) has been investigated in an electrochemical reactor with solid polymer electrolyte (SPE). Methods: Nafion 117 cationic exchange membrane as SPE has been used. Anode/Nafion/cathode sandwiches were constructed by sandwiching Nafion between two dimensionally stable anodes (JP202 electrode). Experiments were conducted to examine the effects of applied current (0.5~2.0 A), supporting electrolyte type (0.2 N NaCl, $Na_2SO_4$, and 1.0 g/L NaCl), initial RhB concentration (2.5~30.0 mg/L) on RhB and COD degradation and $UV_{254}$ absorbance. Results: Experimental results showed that an increase of applied current in electrolysis reaction with solid polymer electrolyte has resulted in the increase of RhB and $UV_{254}$ degradation. Performance for RhB degradation by electrolyte type was best with NaCl 0.2 N followed by SPE, and $Na_2SO_4$. However, the decrease of $UV_{254}$ absorbance of RhB was different from RhB degradation: SPE > NaCl 0.2 N > $Na_2SO_4$. RhB and $UV_{254}$ absorbance decreased linearly with time regardless of the initial concentration. The initial RhB and COD degradation in electrolysis reaction using SPE showed a pseudo-first order kinetics and rate constants were 0.0617 ($R^2=0.9843$) and 0.0216 ($R^2=0.9776$), respectively. Conclusions: Degradation of RhB in the electrochemical reactor with SPE can be achieved applying electrochemical oxidation. Supporting electrolyte has no positive effect on the final $UV_{254}$ absorbance and COD degradation. Mineralization of COD may take a relatively longer time than that of the RhB degradation.