• 한국전기화학회:학술대회논문집
• /
• 2002.10a
• /
• pp.61-61
• /
• 2002

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1995.11a
• /
• pp.77-78
• /
• 1995

• 한국전기화학회:학술대회논문집
• /
• 2003.04a
• /
• pp.56-56
• /
• 2003

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.222-225
• /
• 1999

Started upon it discovery by Wright et al in 1973, studies on the solid polymer electrolyte are being carried out vigorously. So, models of Li-polymer battery have been developed through R-L-C components combination and P-spice functional block in this paper. The impedance characteristics of Li-polymer battery with R-L-C components are presented. Simulation results using P-spice functional model are compared with measured charge/discharge characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.497-500
• /
• 1997

Conducting polymer is new material in lithium secondary battery. conducting polymer has a lot of merit which is flexible and good handing so that this material is used battery system, solid polymer electrolytes airs used PEO(Polyethylene oxide) and PEO/PMMA branding material adding by liquid plasticizer or lithium salt polymer electrolyte which is added liquid plasticizer, lithium salt decreased the crystallity and thermal stability is over than 13$0^{\circ}C$. it is very useful tn apply lithium secondary battery system.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1229-1232
• /
• 1994

The purpose of this study is to research and develop solid polymer electrolyte(SPE) for Li secondary battery. This paper describes the effects of lithium salts, plasticizer addition and temperature dependence of conductivity of PEO electrolytes. Polyethylene oxide(PEO) based polymer electrolyte films were prepared by solution casting an acetonitrile solution of preweighed PEO and Li salt. After solvent evaporation, the electrolyte films were vacuum-dried at $60^{\circ}C$ for 48h, the thickness of the films were $90{\sim}110{\mu}m$. The conductivity properties of prepared PEO electrolytes are summarized as follows. PEO electrolyte complexed with $LiClO_4$ shows the better conductivity of the others. $PEO-LiClO_4$ electrolyte when $EO/Li^+$ ratio is 8, showed the best conductivity. Optimum operating temperature of PEO electrolyte is $60^{\circ}C$. By adding propylene carbonate and ethylene carbonate to $PEO-LiClO_4$ electrolyte, its conductivity was higher than $PEO-LiClO_4$ without those. Also $PEO_8LiClO_4$ electrolyte remains static up to 4.5V vs. $Li/Li^+$.

• Journal of the Korean Ceramic Society
• /
• v.43 no.12 s.295
• /
• pp.751-757
• /
• 2006

Recently, a new type of solid oxide fuel cells has been developed employing extremely thin oxide electrolyte. These fuel cells are expected to operate at significantly reduced temperature compared to conventional solid oxide fuel cells. Accordingly, they may resolve the stability and material selection issues of high temperature fuel cells. Furthermore, they may eliminate the limitations of polymer membrane fuel cells whose operation temperature is under $100^{\circ}C$. In this paper, we review the electrolytes for intermediate temperature operation. Then, we discuss the current development of thin film solid oxide fuel cells that possibly operated at low temperatures.

• Journal of the Korean Chemical Society
• /
• v.67 no.6
• /
• pp.429-440
• /
• 2023

1,1-Dialkyl-2,5-bis(trimethylsilylethynyl)-3,4-diphenylsiloles (R=Et, i-Pr, n-Hex; 3a-c) were prepared and utilized as anode active materials for lithium-ion batteries; 3a was also used as a filler for the solid-state electrolytes (SSE). Siloles 3a-c were prepared by substitution reactions in which the two bromine groups of 1,1-dialkyl-2,5-dibromo-3,4-diphe- nylsiloles, used as precursors, were substituted with trimethylsilylacetylene in the presence of palladium chloride, copper iodide, and triphenylphosphine in diisopropylamine. Among siloles 3a-c, 3a had the best electrochemical properties as an anode material for lithium-ion batteries, including an initial capacity of 758 mAhg^-1 (0.1 A/g), which was reduced to 547 mAhg^-1 and then increased to 1,225 mAhg^-1 at 500 cycles. A 3a-composite polymer electrolyte (3a-CPE) was prepared using silole 3a as an additive at concentrations of 1, 2, 3, and 4 wt.%. The 2 wt.% 3a-CPE composite afforded an excellent ionic conductivity of 1.09 × 10^-3 Scm^-1 at 60℃, indicating that silole 3a has potential applicability as an anode active material for lithium-ion batteries, and can also be used as an additive for the SSE of lithium-ion batteries.

• Membrane Journal
• /
• v.29 no.6
• /
• pp.323-328
• /
• 2019

It is a highly important problem for mankind to supply sufficient energy, which has been connected to production and supply of electricity. In terms of the problems, this study fabricated a new sort of solid polymer electrolyte membrane for supercapacitors. The fabricated electrolyte employed grafting poly(oxyethylene methacrylate) (POEM) side chain on poly(vinyl alcohol) (PVA) main chain by free-radical polymerization. It is the first time to utilize PVA-g-POEM graft copolymer as an electrolyte membrane for supercapacitor. The chain behavior of PVA was transformed by grafting POEM side chains, which was analyzed by FT-IR spectra. Also, the capacitance performances of fabricated supercapacitors were explored by cyclic voltammetry (CV), galvanostatic charge/discharge (GCD), and ragone plot. We suggest a new point, the grafting of the electrolyte of supercapacitor in this study.

• Elastomers and Composites
• /
• v.39 no.1
• /
• pp.36-41
• /
• 2004

Solid polymer electrolytes were prepared by UV irradiation of the blends consisting of poly(ethylene oxide)(PEO), epoxy diacrylate(EDA) and LiClO_4$. Conductivities of the electrolyte films were measured as a function or blend composition, salt concentration and temperature. The electrolyte having the composition of poly(ethylene oxide) (70% by weight)/epoxy diacrylate (30% by weight) with mole ratio of 10 of ethylene $oxide/Li^+$ exhibited a high ionic conductivity of $1.2{\times}10^{-5} S/cm$ at $25^{\circ}C$. This blend is transparent and shows elastomeric properties. Morphological studies by means of differential scanning calorimetry, X-ray diffraction and polarized optical microscopy indicated that the cured epoxy chains in the blends inhibit the crystallization of poly (ethylene oxide) and thereby induce the blend systems to be completely amorphous in certain compositions.