• 한국주조공학회지
• /
• 제22권2호
• /
• pp.82-88
• /
• 2002

Al-5.5Zn-2.5Mg-l.5Cu semi-solid slurry was prepared by cooling the liquid metal with a low superheat to a solid and liquid co-existing temperature. Relatively round solid particles could be obtained in the slurry through the simple process. The prepared slurry was deformed into the metallic mold by a press and the mechanical properties of obtained specimens were investigated. Mold filling ability of the alloy slurry was also investigated and compared with that of A356 alloy. Al-Zn-Mg-Cu alloy showed lower mold filling ability than A356 alloy probably because small amount of eutectic phase is present and the heat of fusion generated during solidification is smaller than that of A356 alloy.

• 한국주조공학회지
• /
• 제9권4호
• /
• pp.311-319
• /
• 1989

The effects of the alloying elements and cooling rates on the formation of phosphide eutectics of compacted vermicular graphite cast irons containing copper, tin, molybdenum for producing pearlitic matrix, and also containing phosphorus and boron for increasing wear resistance, were investigated. The liquidus phosphide eutectic was found to solidify as a pseudo-binary phosphide eutectic, but with increasing of the cooling rate non-equlibrium phosphide eutectic with needle type carbide could be formed. However, the liquidus phosphide eutectic containing both phosphorus and carbide-forming boron was found to solidify always as a non-equlibrium phosphide eutectic with coarse carbide, independent from the cooling rate. It was also confirmed that the tiny isolated phase observed by SEM was gamma iron solid solution with phosphorus, silicon, molybdenum and the matrix containing these tiny islands was phosphide phase containing manganese and molybdenum. The addition of copper was found to decrease the tendency of forming ledeburitic carbides in the phosphide eutectic.

• 공업화학
• /
• 제20권3호
• /
• pp.317-321
• /
• 2009

고체 산화물 전해질로 사용되고 있는 초 이온 전도체인 $K^+-{\beta}/{\beta}"-Al_2O_3$의 고온 상관계와 소결성 분석을 위하여 $K_2O-LiO_2-Al_2O_3$ 삼성분계로부터 고상반응을 통하여 순수한 $K^+-{\beta}/{\beta}"-Al_2O_3$ 분말을 합성한 후 slip casting방법과 냉간정수압성형에 의하여 tube와 disk형을 각각 제작하였다. Slip casting은 40 wt%의 고체함량을 가지는 슬러리를 사용해 알루미나 몰드에서 이루어졌고 냉간정수압성형은 20 MPa의 압력하에서 수행되었다. 성형체들은 $1600^{\circ}C$, $1700^{\circ}C$, $1750^{\circ}C$에서 각각 소결하여 성형방법에 따른 상관계와 소결밀도를 조사하였다. 냉간정수압성형에 의한 시편이 $1700^{\circ}C$까지 ${\beta}"-Al_2O_3$의 상분율이 월등히 높은 반면, 소결밀도에 있어서는 slip casting방법의 경우가 다소 높았다. 소결 시 상대밀도는 $1750^{\circ}C$에서 1 h 경과 후, 두 경우 모두 약 83%를 나타내었다. 90 min 이상 소결하였을 때는 입자의 과대성장과 기공으로 인해 오히려 밀도가 낮아졌다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.247-248
• /
• 2006

In this study, the morphology of the change of primary Al phase in A356 alloy by two kinds of electromagnetic stirrers(vertical and horizontal) were investigated to obtain the globular structure. The effects of the stirring current, the stirring time and the pouring temperature were determined. The greater stirring current and longer stirring time were to get the finer the Al phase. However, over a certain stirring current and stirring time, the primary Al was merged together and was increased. The reason is the degree of breakdown of initial dendrites has been decreased by the collision and coalescence of particles with increasing stirring current and stirring time. The optimum conditions and difference of the two kinds of electromagnetic stirrers have been investigated for rheology forming with controlled solid fraction.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.8.1-8.1
• /
• 2009

The self-assembly of peptide-based building blocks into nanostructures is an attractive route for fabricating novel materials because of their capacity for molecular recognition and functional flexibility as well as the mild conditions required in the fabrication process. Among various peptide-based building blocks forming nanostructures, the simplest building blocks are aromatic dipeptides like diphenylalanine, which can readily self-assemble into nanotubes in aqueous solutions at ambient conditions. Recently, we have developed a high-temperature solid-phase self-assembly process for diphenylalanine. Through this novel process, we succeeded in the growth of vertically well-aligned, uniform nanowires from amorphous peptide thin film. To demonstrate the versatility of our approach, we also fabricated a micropattern of peptide nanowires by combining our solid-phase growth method and simple soft lithographic techniques. We believe that our studies on peptide self-assembly will provide a new horizon for peptide-based nanofabrication.

• 한국전기전자재료학회논문지
• /
• 제22권6호
• /
• pp.462-465
• /
• 2009

Schottky barrier thin film transistors (SB-TFT) on polycrystalline silicon(poly-Si) are fabricated by platinum silicided source/drain for p-type SB-TFT. High quality poly-Si film were obtained by crystallizing the amorphous Si film with excimer laser annealing (ELA) or solid phase crystallization (SPC) method, The fabricated poly-Si SB-TFTs showed low leakage current level and a large on/off current ratio larger than 10), Significant improvement of electrical characteristics were obtained by the additional forming gas annealing in 2% $H_2/N_2$ ambient, which is attributed to the termination of dangling bond at the poly-Si grain boundaries as well as the reduction of interface trap states at gate oxide/poly-Si channel.

• BMB Reports
• /
• 제37권4호
• /
• pp.460-465
• /
• 2004

A 16-residue polypeptide model with the sequence acetyl-YALSLAATLLKEAASL-OH was derived by rational de novo peptide design. The designed sequence consists of amino acid residues with high propensity to adopt an alpha helical conformation, and sequential order was arranged to produce an amphipathic surface. The designed sequence was chemically synthesized using a solid-phase method and the polypeptide was purified by reverse-phase liquid chromatography. Molecular mass analysis by electro-spray ionization mass spectroscopy confirmed the correct designed sequence. Structural characterization by circular dichroism spectroscopy demonstrated that the peptide adopts the expected alpha helical conformation in 50% acetonitrile solution. Liposome binding assay using Small Unilamellar Vesicle (SUV) showed a marked release of entrapped glucose by interaction between the lipid membrane and the tested peptide. The channel-forming activity of the peptide was revealed by a planar lipid bilayer experiment. An analysis of the conducting current at various applied potentials suggested that the peptide forms a cationic ion channel with an intrinsic conductance of 188 pS. These results demonstrate that a simple rational de novo design can be successfully employed to create short peptides with desired structures and functions.

• 한국자동차공학회논문집
• /
• 제4권5호
• /
• pp.206-214
• /
• 1996

Because of the wide variety of the composite materials, inherent variability in properties, and complex temperature and strain rate dependence, large strain behavior of these materials has not been well characterized. Large strain behavior under uniaxial tension is characterized over a range of temperatures and strain rates, and a modified simple linear viscoelastic model is fit to the observed data. Of particular importance is the strain rate and temperature dependence of these composites, and it is the primary focus of this study. The strain rate and temperature dependence is then used to predict limiting tensile strains, based on Marciniak imperfection theory. Excellent correlation was obtained between model and experiment and the results are summarized in maps of forming limit as a function of strain rate and temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.147-151
• /
• 1996

Brewster angle microscopy(BAM) makes it possible to observe the monolayer states on the water subphase and the phase transitions from a gaseous phase via a expanded phase to a condensed phase. Also BAM can be used to observe the films on the solid substrate such as Langmuir-Blodgett(LB) films. In this Paper Polyamic Acid Alkylamine Salts(PAAS) was used for forming L films and LB films and $\pi$-A isotherm showed pressure of each phase. We obtained BAM images as surface pressure increased. Images of LB films were compared with data from ellipsometry which was used to measure the film thickness. Images of both L films and LB films were analyzed with computer in the point of brightness.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.194-197
• /
• 1999

고분자 복합재료는 금속에 비하여 경량, 고강도, 고탄성율 등의 장점을 가지고 있어 여러 산업에서 기존의 금속 재료를 대체할 수 있는 재료로서 그 사용이 점차 증가하고 있다[1-5]. 특히 사회적으로 환경 문제가 대두되면서 열가소성 복합재료에 대한 관심이 높아지고 있으며 이에 대한 연구가 더욱 요구되고 있다. (중략)