• 한국세라믹학회지
• /
• 제51권1호
• /
• pp.51-56
• /
• 2014

Mixed ionic and electronic conducting $K_2NiF_4$-type oxide, $Nd_{2-x}Sr_xNiO_{4+\delta}$ (x = 0, 0.4, 0.6) powders were synthesized by a solid-state reaction technique and solid oxide fuel cells consisting of a $Nd_{2-x}Sr_xNiO_{4+\delta}-GDC$ cathode, a Ni-YSZ anode and 8YSZ as an electrolyte were fabricated. The effect of strontium substitution for neodymium on the electrical and electrochemical properties was examined. The electrical conductivity increased with an increase in the Sr doping content, while it appears that the excess oxygen (${\delta}$) decreased. Sr doping into $Nd_2NiO_{4+\delta}$ resulted in an increase in the cathode polarization resistance and an decrease in the power density of the cell. These phenomena may be associated with the decreased amount of excess oxygen noted in the $Nd_{2-x}Sr_xNiO_{4+\delta}$ cathode.

• 한국세라믹학회지
• /
• 제44권12호
• /
• pp.733-739
• /
• 2007

NiO-YSZ anode-supported single cell was prepared by spin-coating YSZ and LSM slurries as electrolyte and cathode, respectively. Dense YSZ electrolyte film was successfully prepared on the porous NiO-YSZ anode substrate by tuning pre-sintering temperature of NiO-YSZ and co-firing temperature. The thickness of YSZ film was controlled by the solid content of slurry and coating cycles. The experimental conditions affecting on the thickness of YSZ film was discussed. Single cells with the active electrode area ${\sim}0.8\;cm^2$ were prepared by spin-coating the cathode layers of LSM-YSZ mixture and LSM consequently as well. The effects of the pre-sintering temperature and thus the microstructure of NiO-YSZ substrate on the current-voltage characteristics of co-fired cell were investigated.

• Korean Chemical Engineering Research
• /
• 제46권4호
• /
• pp.813-818
• /
• 2008

고체 산화물 연료전지(SOFC)에서 Ni/YSZ 음극 촉매를 이용한 내부 개질 반응 시 코크 형성에 의한 촉매 비활성화 문제점을 개선하기 위해 음극에 여러가지 조촉매(Ce, Co, Cu, Cr, Mn, Pd, K, $K_2Ti_2O_5$)들을 첨가하여 그 영향을 조사하였다. $H_2O/CH_4=1.5$ 몰비, 800의 반응 조건하에서 수증기 개질 반응을 행한 결과 전이금속산화물들은 코크형성을 억제하는 효과가 없었고 메탄전환율도 오히려 감소하였다. Potassium을 담지한 Ni/YSZ의 경우는 초기에는 뚜렷한 코크형성 억제 효과가 있었으나 반응 후 42시간이 지나면 휘발에 의한 Potassium함량 감소로 급격한 촉매활성의 저하가 일어났다. 격자 구조에 Potassium이 내장된 $K_2Ti_2O_5$를 5% 혼합한 Ni/YSZ의 경우에는 장기간 운전에도 반응 활성이 줄어들지 않아서 음극 촉매의 코크 억제용 첨가제로 적용될 수 있음을 알았다. 반응시간에 따른 촉매의 비활성화는 촉매 표면에서의 graphidic carbon의 생성 때문으로 밝혀졌다.

• Transactions on Electrical and Electronic Materials
• /
• 제15권4호
• /
• pp.189-192
• /
• 2014

Yttria-stablized zirconia (YSZ) is the most commonly used electrolyte material, but the reduction in working temperature leads to insufficient ionic conductivity. Ceria based electrolytes (GDC) are more attractive in terms of conductivity at low temperature, but these materials are well known to be reducible at very low oxygen partial pressure. The reduction of electrolyte resistivity is necessary to overcome cell performance losses. So, thin YSZ/GDC bilayer technology seems suitable for decreasing the electrolyte resistance at lower operating temperatures. Bilayer electrolytes composed of a galdolinium-doped $CeO_2$ ($Ce_{0.9}Gd_{0.1}O_{1.95}$, GDC) layer and yttria-stabilized $ZrO_2$ (YSZ) layer with various thicknesses were deposited by RF sputtering and E-beam evaporation. The bilayer electrolytes were deposited between porous Ni-GDC anode and LSM cathode for anode-supported single cells. Thin film structure and surface morphology were investigated by X-ray diffraction (XRD), using $CuK{\alpha}$-radiation in the range of 2ce morphol$^{\circ}C$. The XRD patterns exhibit a well-formed cubic fluorite structure, and sharp lines of XRD peaks can be observed, which indicate a single solid solution. The morphology and size of the prepared particles were investigated by field-emission scanning electron microscopy (FE-SEM). The performance of the cells was evaluated over $500{\sim}800^{\circ}C$, using humidified hydrogen as fuel, and air as oxidant.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.17-18
• /
• 2007

Solid oxide fuel cells are clean, pollution-free technology for the electrochemical generation of electricity at high efficiency. Specially, the polarization resistance between electrolyte and electrode of SOFC unit cell is of importance, because it is desirable to develop SOFC operating at intermediate temperature below $800^{\circ}C$. The LSCF cathode prepared using modified oxalate method was investigated with different electrolyte. A precursor was prepared with oxalic acid, ethanol and $NH_4OH$ solution. The LSCF precursor was prepared at $80^{\circ}C$, and pH control was 2, 6, 8, 9 and 10. The precursor powder was calcined at $800^{\circ}C$, $1000^{\circ}C$ and $1200^{\circ}C$ for 4hrs. The crystal of LSCF powders show single phase at pH 2, 6, 8 and 9, and the average particle size was about $3{\mu}m$. The LSCF cathode with heat treatment at $1200^{\circ}C$ showed a plot of electric conductivity versus temperature. Unit cell prepared from the LSCF cathode, buffer layer between cathode and electrolyte and the LSGM, YSZ, ScSZ and CeSZ electrolyte. Also interface reaction between LSCF, buffer layer and electrolyte were measured by EPMA and the polarization resistance for unit cell with cycle measure using a Solatron 1260 analyzer.

• 대한기계학회논문집B
• /
• 제35권4호
• /
• pp.399-407
• /
• 2011

고체산화물 연료전지(SOFC)와 가스터빈을 결합한 하이브리드 발전시스템에서 가스터빈의 규모별 성능차이가 시스템의 성능에 미치는 영향에 대하여 해석하였다. 이를 위해 kW급, MW 이하급, 수 MW급 등 서로 다른 세 가지 가스터빈을 선정하여 사용하였다. 가스터빈이 순 출력을 거의 내지 못하는 kW급 시스템에서도 연료전지 단독 시스템과 비교해 효율이 증가하였으며, 가스터빈의 출력이 커질수록 (즉, 성능이 좋아질수록) 하이브리드 시스템에서 가스터빈이 차지하는 비중이 커지고 시스템의 효율이 높아짐을 확인하였다. 가스터빈의 압력비 증가에 따른 성능 변화를 살펴본 결과 세 가지 하이브리드 시스템에서 모두 출력은 증가하지만, 효율의 변화는 크지 않음을 확인하였다.

• 한국세라믹학회지
• /
• 제36권4호
• /
• pp.391-402
• /
• 1999

Characteristics of composite electrolytes which were prepared by coating a thin film of YSZ (yttria sta-bilized zirconia : (ZrO2)0.92 (Y2O3)0.08) on YDC (yttria doped ceria : Ce0.8Y0.2O1.9) with mixed conductivity have been investigated in order to develop the low-temperature solid oxide fuel cell. The thickness (t) of spin-coated YSZ thin films after the heat-treatment at 600$^{\circ}C$ was increased proportionally to the sol con-centrations (C) while the decrease in its thickness with the spin rate ($\omega$) could be expressed in the e-quation of ln t=9.49-0.53 ln $\omega$(0.99mol//s sol conc.) When the sol concentration and the spin rate being less than 0.99 mol/l and higher than 1000 rpm respectively reliable YSZ/YDC composite electrolytes could be obtained by multi-coating although several micro-cracks were observed in singly coated YSZ film surfaces. The dense YSZ film with a 1$\mu\textrm{m}$ thickness was prepared by coating of 0.99 mol/l YSZ sol five-times at 2000 rpm followed by heat-treatment at 1400$^{\circ}C$ for 2h, The adhesion between YSZ film and YDC substrate was found to be very good. The open circuit voltages of H2/O2 single cell with YSZ/YDC composite electrolytes were 0.79∼0.82 V at 800$^{\circ}C$ and 0.75∼0.77V at 900$^{\circ}C$ The open circuit voltage was inversely proportioned to the thickness ratio of YSZ thin film (1$\mu\textrm{m}$) to YDC substrate(0.28-2.22 mm)

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.56.1-56.1
• /
• 2009

The intermediate operating temperature of solid oxide fuel cells (IT-SOFCs) have achieved considerable importance in the area of power fabrication. This is because to improve materials compatibility, their long-term stability and cost saving potential. However, to conserve rational cell performance at reduced-temperature regime, cathode performance should be obtained without negotiating the internal resistance and the electrode kinetics of the cell. Recently, double perovskite structure cathodes have been studied with great attention as a potential material for IT-SOFCs. In this study, double-perovskite structured cathodes of $GdBaCoCuO_{5+\delta}$, $GdBaCo_{2/3}Cu_{2/3}Fe_{2/3}O_{5+\delta}$ compositions and $(1-x)GdBaCo_2O_{5+\delta}+xCe_{0.9}Gd_{0.1}O_{1.95}$ (x = 10, 20, 30 and 40 wt.%) composites were evaluated as the cathode for intermediate temperature solid oxide fuel cells(IT-SOFCs). Electrical conductivity of the cathodes were measured by DC 4-probe method, and the thermal expansion coefficient of each sample was measured up to $900^{\circ}C$ by a dilatometer study. Area specific resistances(ASR) of the $GdBaCo_{2/3}Cu_{2/3}Fe_{2/3}O_{5+\delta}$ cathode and 70 wt.% $GdBaCo_2O5+\delta$ + 30wt.% Ce0.9Gd0.1O1.95 composite cathode on CGO electrolyte substrate were analyzed using AC 3-probe impedance study. The obtained results demonstrate that double perovskite-based compositions are promising cathode materials for IT-SOFCs.

• 한국분말재료학회지
• /
• 제15권5호
• /
• pp.405-410
• /
• 2008

SOFC (Solid Oxide Fuel Cell) Ni-YSZ anode was fabricated by the spark plasma sintering (SPS) process and its microstructure and electrical properties were investigated in this study. The spark plasma sintering process was carried out at $800{\sim}1000^{\circ}C$ for holding time of 5 min under 40 MPa. To fabricate Ni-YSZ anode, the SPS processed specimens were reduced at $800^{\circ}C$ under $H_2$ atmosphere. The reduced specimens showed relative density of $48.4{\sim}64.8%$ according to sintering temperature. And also, the electrical conductivity of reduced specimens after sintering at 900 and $1000^{\circ}C$ showed $480{\sim}600$ (S/cm) values at the measuring range of $600{\sim}900^{\circ}C$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1051-1053
• /
• 1995

Nowadays perovskite $La_{1-x}Sr_xMnO_3$ is preferred cathode material in Solid Oxide Fuel cell(SOFC). The $La_{1-x}Sr_xMnO_3$ with Sr contents ranging $x=0{\sim}1.0$ were prepared by a citrate method. These powders were characterized by usual means like TG/DTA, X-ray diffraction analysis. The samples used for measuring thermal expansion were prepared as pellets by cold pressing and subsequent sintering in air at $1200^{\circ}C$ for 5 hours. To measure the by-product of $La_{1-x}Sr_xMnO_3$ reacted with 8mol% YSZ, that samples were sintered at $1200^{\circ}C$ for 5 hours.