• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.243-243
• /
• 2010

This paper two different etching, HF : HNO3 :DI and RIE were used for etching in multi-crystalline Silicon(Mc-Si) solar cell fabrication. The wafers etched in RIE texture showed low reflectance compared to the wafers etched in Acid soultion after SiNx deposition. In light current-voltage results, the cells etched in RIE texture exhibited higher short circuit current and open circuit voltage than those of the cells etched in acid solution. We have obtained 15.1% conversion efficiency in large area($156cm^2$) Multi-Si solar cells etched in RIE texture.

• Journal of Electrochemical Science and Technology
• /
• v.7 no.1
• /
• pp.52-57
• /
• 2016

Nanoporous-layer-covered TiO₂ nanotube arrays (Type II TNTs) were fabricated by two-step electrochemical anodization. For comparison, conventional TiO₂ nanotube arrays (Type I TNTs) were also prepared by one-step electrochemical anodization. Types I and II TNTs were detached by selective etching and then transferred successfully to a transparent F-doped SnO₂ (FTO) substrate by a sol-gel process. Both FTO/Types I and II TNTs allowed front side illumination to exhibit incident photon-to-current efficiencies (IPCEs) in the long wavelength region of 300 to 750 nm without the absorption of light by the iodine-containing electrolyte. The Type II TNT exhibited longer electron lifetime and faster charge transfer than the Type I TNT because of its relatively fewer defect states. These beneficial effects lead to a high overall energy conversion efficiency (5.32 %) of the resulting dye-sensitized solar cell.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.4
• /
• pp.1-7
• /
• 2014

The microgrid system is the combination of photovoltaic(PV) array, load, and battery energy storage system. The control strategies were defined as multi-modes of operation, including rest operation without use of battery, power charging, and power discharging, which enables grid connected mode or islanded mode. Photovoltaic power is a problem of the uniformity of power quality because the power generated from solar light is very sensitive to variation of insolation and duration of sunshine. As a solution to the above problem, energy storage system(ESS) is considered generally. There fore, in this study, we did basic research activities about optimization method of the amount of energy used, using a smart microgrid test-bed constructed in building. First, we analyzed the daily, monthly and period energy pattern amount of power energy used, and analyzed PV power generation level which is built on the roof. Utilizing building energy pattern analysis data, we was studied an efficient method of employing the ESS about building power consumption pattern and PV generation.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1645-1647
• /
• 1996

Polycrystalline CdTe thin films -have been studied for photovoltaic application because of their high absorption coefficient and optimal band gap energy (1.54 eV) for solar energy conversion. In this study, we prepared CdTe films using RF-magnetron sputtering method and investigated structural, optical and electrical properties with spectrophotometer, XRD, EDX, and resistivity meter. CdTe films at $200\;^{\circ}C$ showed a mixture of zinc blend (Cubic) and wurtzite (hexagonal) phase. On the other hand, the films at $400\;^{\circ}C$ showed highly oriented structure having hexagonal structure. The resistivity of CdTe films deposited on $SiO_2$ substrates was about $10_7\;{\Omega}cm$. The value of resistivity decreased with the increase of the substrate temperature. CdTe were sputtered on CdS thin films prepared by chemical bath deposition for the formation of the heterojunction. I-V characteristics of these cells were measured at a light density of $100mw/cm^2$, AM. 1.0. The present thin film solar cells showed a conversion efficiency of about 5%.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1256-1257
• /
• 2008

Dye-Sensitized Solar Cell(DSSC) is a new type of solar cell by using photocatalytic properties of $TiO_2$. The size and shape of $TiO_2$ particle are two of important parameters that are related to the characteristics of DSSC. And these can be changed by controlling $TiO_2$ sintering conditions especially temperature. The particles of $TiO_2$ are classified anatase and rutile. Anatase particles are created at low sintering temperature and rutile particles are created at high sintering temperature. Anatase particles have advantages such as increased surfaces that cause more attached dye molecules, and fast electron transportation. And rutile particles have advatages such as more efficient light scattering. Therefore, we studied characteristics of DSSC in this paper as $TiO_2$ sintering temperature is varied. As a result, we found that characteristics of DSSC are very good in the case that anatase and rutile particles are together and this sintering temperature is 450$^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.72-72
• /
• 2010

Recent development of organic solar cell approaches the level of 8% power conversion efficiency by the introduction of new materials, improved material engineering, and more sophisticated device structures. As for interface engineering, various interlayer materials such as LiF, CaO, NaF, and KF have been utilized between Al electrode and active layer. Those materials lower the work function of cathode and interface barrier, protect the active layer, enhance charge collection efficiency, and induce active layer doping. However, the addition of another step of thin layer deposition could be a little complicated. Thus, on a typical solar cell structure of Al/P3HT:PCBM/PEDOT:PSS/ITO glass, we used Li:Al alloy electrode instead of Al to render a simple process. J-V measurement under dark and light illumination on the polymer solar cell using Li:Al cathode shows the improvement in electric properties such as decrease in leakage current and series resistance, and increase in circuit current density. This effective charge collection and electron transport correspond to lowered energy barrier for electron transport at the interface, which is measured by ultraviolet photoelectron spectroscopy. Indeed, through the measurement of secondary ion mass spectroscopy, the Li atoms turn out to be located mainly at the interface between polymer and Al metal. In addition, the chemical reaction between polymer and metal electrodes are measured by X-ray photoelectron spectroscopy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.346.1-346.1
• /
• 2014

Porous nano crystalline $TiO_2$ is currently used as a working electrode in a dye-sensitized solar cell (DSSC). The conventional working electrode is comprised of absorption layer (particle size:~20 nm) and scattering layer (particle size:~300 nm). We inserted window layer with 10 nm particle size in order to increase transmittance and specific surface area of $TiO_2$. The electrochemical impedance spectroscope analysis was conducted to analysis characterization of the electronic behavior. The Bode phase plot and Nyquist plot were interpreted to confirm the internal resistance caused by the insertion of window layer and carrier lifetime. The photocurrent that occurred in working electrode, which is caused by rise in specific surface area, increased. Accordingly, it was found that insertion of window layer in the working electrode lead to not only effectively transmitting the light, but also increasing of specific surface area. Therefore, it was concluded that insertion of window layer contributes to high conversion efficiency of DSSCs.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.30.2-30.2
• /
• 2010

Nano-scale p-n junction can generate various nano-scale functional devices such as nanowire light emitting diode, nanowire solar cell, and nanowire sensor. The core shell type nanowire p-n junction has been considered for the high efficient devices in many previous reports. On the other hand, although device efficiency is relatively lower, the cross bar type p-n junction has simple topological structure, suggested by C.M. Lieber group, to integrate easily many p-n junction devices in one board. In this study, for the integration of the cross bar nanowire p-n junction device, a simple fabrication route, employed dielectrophoretic array and direct printing techniques, was demonstrated by the successful fabrication and programmable integration of the nanowire cross bar p-n junction solar cell. This direct printing process will give the single nanowire solar cell the opportunity of the integration on the circuit board with other nanowire functional devices.

• Korean Chemical Engineering Research
• /
• v.45 no.5
• /
• pp.415-423
• /
• 2007

Photocatalytic water splitting (PWS) is the most promising technology to produce $H_2$ energy directly from renewable water and solar light. In spite of the remarkable progress made in the last decade, there are still many technical challenges remaining particularly in finding new photocatalytic materials with high efficiency and durability. This article discusses the application of nanocomposite materials in search of new photocatalytic materials for solar hydrogen production from water. It has been demonstrated that smart combination and modification of known materials and functions could be fruitful approach for the purpose.

• Rapid Communication in Photoscience
• /
• v.2 no.3
• /
• pp.82-84
• /
• 2013

We fabricated dye-sensitized solar cells (DSSCs) with $TiO_2$ nanowire (NW)/nanoparticle (NP) composite and solidified nanogel as the photoelectrode and electrolyte, respectively. $TiO_2$ NWs were generated via pore-infiltration of titanium (IV) isopropoxide (TTIP) into a track-etched polycarbonate membrane with a pore diameter of 100 nm, followed by calcination at $500^{\circ}C$. Energy conversion efficiency of $TiO_2$ NW/NP-based DSSCs was always higher than that of NP-based cells. We attributed this to improved light scattering and electron transport by $TiO_2$ NWs, as verified by intensity modulation photocurrent spectroscopy (IMPS) and intensity modulation photovoltage spectroscopy (IMVS) analyses. Quasi-solid-state DSSCs with NW/NP composites exhibited 5.0% efficiency at 100 $mW/cm^2$, which was much greater than that of NP-based cells (3.2%).