• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.3-4
• /
• 2008

Photovoltaic module consists of serially connected solar cell which has low voltage characteristics. But, the other way, the whole current flow of PV module is restricted by lowest current of one solar cell. For the experiment, we make PV module composing the solar cells that have short circuit current difference of 0%, 1%, 3% and 5%. Using Light I-V and Dark I-V measurements, electrical characteristic parameters like Isc(short-circuit current), Voc(open-circuit voltage), Rs(series resistance), Rsh(shunt resistance) are analyzed. PV module of low current characteristics has electrical stress from other modules. And, such a module has a tendency of hot-spot suffering which leads degradation.

• 한국재료학회지
• /
• 제30권5호
• /
• pp.262-266
• /
• 2020

In this paper, we investigated the effect of the passivation stack with Al₂O₃, hydrogenated silicon nitride (SiN_x:H) stack and Al₂O₃, silicon oxynitride (SiON_x) stack in the n type bifacial solar cell on monocrystalline silicon. SiNx:H and SiON_x films were deposited by plasma enhanced chemical vapor deposition on the Al₂O₃ thin film deposited by thermal atomic layer deposition. We focus on passivation properties of the two stack structure after laser ablation process in order to improve bifaciality of the cell. Our results showed SiN_x:H with Al₂O₃ stack is 10 mV higher in implied open circuit voltage and 60 ㎲ higher in minority carrier lifetime than SiON_x with Al₂O₃ stack at Ni silicide formation temperature for 1.8% open area ratio. This can be explained by hydrogen passivation at the Al₂O₃/Si interface and Al₂O₃ layer of laser damaged area during annealing.

• 신재생에너지
• /
• 제3권4호
• /
• pp.54-62
• /
• 2007

In this paper, we report the research highlight on the preparation and characterization of Indium-free $Cu_2ZnSnSe_4$ and Indium-reduced $CulnZnSe_2$ thin films in order to seek the viability of these absorber materials to be applied in thin film solar cells. The films of $Cu_2ZnSnSe_4\;and\;CulnZnSe_2$ were prepared using mixed binary chalcogenides powders. It was observed that Cu concentration was a function of substrate temperature as well as CuSe mole ratio in the target. Under an optimized condition, $Cu_2ZnSnSe_4\;and\;CulnZnSe_2$ thin films grew with strong [112]. [220/204] and [312/116] reflections. Both $Cu_2ZnSnSe_4\;and\;CulnZnSe_2$ films were found to exhibit a high absorption coefficient of $104^4cm^{-1}\;Cu_2ZnSnSe_4$ film showed a band gap of 1.5eV which closes to the optimum band gap of an ideal solar absorber for a solar cell. On the other side, an increase of optical band gap from 1.0 to 1.25eV was found to be proportional with an increase of Zn concentration in the $CulnZnSe_2$ film. All films in this study revealed a p-type semiconductor characteristic.

• Current Photovoltaic Research
• /
• 제9권4호
• /
• pp.111-122
• /
• 2021

Silicon heterojunction technology (HJT) solar cells have received considerable attention due to advantages that include high efficiency over 26%, good performance in the real world environment, and easy application to bifacial power generation using symmetric device structure. Furthermore, ultra-highly efficient perovskite/c-Si tandem devices using the HJT bottom cells have been reported. In this paper, we discuss the unique feature of the HJT solar cells, the fabrication processes and the current status of technology development. We also investigate practical challenges and key technologies of the HJT solar cell manufacturers for reducing fabrication cost and increasing productivity.

• 한국태양에너지학회 논문집
• /
• 제32권2호
• /
• pp.35-41
• /
• 2012

Knowledge of the solar radiation components and classified wavelength data are essential for modeling many solar photovoltaic systems. This is particularly the case for applications that concentrate the incident energy to attain high photo-dynamic efficiency achievable only at the higher intensities. In order to estimate the performance of concentrating PV systems, it is necessary to know the intensity of the beam radiation, as only this components can be concentrated, and The new PV cell can generate electricity from ultraviolet and infrared light as well as visible light. The Korea Institute of Energy Research(KIER) has began collecting solar radiation components data since January, 1988, and solar radiation classified wavelength data since November, 2008. KIER's solar radiation components and classified wavelength data will be extensively used by concentrating PV system users or designers as well as by research institutes. It is essential to utilize the solar radiation data as application and development of solar energy system increase. Consider able efforts have been made constructing a standard data base system from measure data.

• 한국산학기술학회논문지
• /
• 제22권5호
• /
• pp.310-316
• /
• 2021

기존의 인공위성은 다기능·높은 성능을 가진 대형위성을 국가 단위에서 운용하는 것이 일반적이었으나 최근의 전기·전자 및 광학 기술의 경량 소형화 발전에 따라 점차 소형위성이 주목받고 있다. 크기와 무게가 감소됨에 따라 적은 비용으로 개발 및 발사가 가능하여 위성 개발에 진입장벽이 낮아지고 있으나, 인공위성의 전력공급에 필수적인 태양전지 패널의 경우 태양광에 효율적으로 노출되기 위해 넓은 표면적이 필요하여 소형화 및 경량화가 제한적이다. 우주용 태양전지는 우주선과 태양열, 온도와 같은 다양한 우주환경을 고려하여 제작되어야하고, 부피를 최적화하기 위해 전개 매커니즘을 적용하며 경량화 및 고효율화를 위하여 태양전지 셀의 구조적 재료적인 연구개발이 필요하다. 현재 태양전지 패널로 개발되어 운용되고 있는 제품들은 고효율화를 위하여 주로 InGaP/GaAs/Ge 소재의 3중구조를 적용하고 있다. 최근에는 초고효율 다층구조 태양전지를 위하여 4중접합 이상의 구조가 연구되고 있으며, 나아가 소재적으로 경량화에 유리한 유연박막 태양전지, 유기 및 유무기 하이브리드 태양전지 등이 차세대 소형위성용 태양전지로 주목받고 있다.

• 한국태양에너지학회 논문집
• /
• 제33권2호
• /
• pp.35-41
• /
• 2013

Dye-sensitized solar cell (DSC) allows light transmission and the application of various colors that make it especially suitable for building-integrated PV (BIPV) application. In order to apply DSC module into windows, it has to be panelized: DSC module should be protected with reinforced glass to the entire surface. Up to date, it seems to be common to make double glazing with DSC modules with air gaps between the glasses and the DSC modules. Few research has been conducted on the characteristics of various glazing types with DSC modules. This study aims to analyze the electrical performance of DSC modules according to panelizing method for glazing unit with DSC modules. The prototype of the DSC glazing that applied silicone filler between DSC modules and glasses was developed. The electrical performances of this type of DSC glazing with the filler and rather conventional double glazing with DSC modules were compared. Their performances were measured using a solar simulator that is suitable for DSC performance testing. The results indicated that the electrical performance of the filler type DSC glazing improved by 7% compared to that of the conventional DSC double glazing type.

• 한국태양에너지학회 논문집
• /
• 제25권4호
• /
• pp.77-83
• /
• 2005

The verified thermal efficiency, thermal capacity confirmed the effects of the cooling system. Therefore, it is useful for preventing the PV cell temperature rising when solar radiation accumulates in summer. When adopting a hybrid panel for the BIPV system, the affected areas include the vertical outside walls facing the south, southeast, and southwest on the curtain walls excluding windows. The standards on replace aluminum panel which were the popular exterior material were investigated, Designing practice made sure that it could be manufactured in various sizes, and confirmed the most proper method to install a hybrid panel in the BIPV system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.1544-1546
• /
• 2004

This paper describes the element of solar cell's characteristics, photovoltaic system and solar tracking through experiment. Furthermore, it proposes the experiment results of the PV system is contained solar modules, power conditioning system and the solar tracking system using air compress charging energy The experimental results show that the PV system is always operated at maximum power of solar cells and tracking the sun in order to generate efficiently power generation and propose a capability of its application.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2010년도 춘계학술대회
• /
• pp.658-661
• /
• 2010

태양에너지의 활용은 새로운 산업의 창출과 함께 다양화 되고 있다. 본 연구에서는 태양에너지를 이용하기 위한 단일 모듈 형태의 전원공급시스템을 구현함으로써 공간적 지배를 받지 않고 전기 공급이 어려운 곳에서도 전기를 효율적으로 충전하고 간편하게 사용할 수 있는 개선된 성능의 전원공급시스템을 개발하고자 한다.