• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.215-225
• /
• 2002

In order to enhance the thermal stability of binder materials of bonded type solid lubricants, several combinations of metal-alkoxide based sol-gel materials such as methyltrimethoxysilane(MTMOS), $titaniumisopropoxide(Ti(Opr^{j})_{4})$, $zirconiumisopropoxide(Zr(Opr^{j})_{4})$ and $aluminumbutoxide(Al(Obu^{t})_{4})$ were chemically modified by epoxy-, acrylic- and fluoro-silane compounds, respectively, in this work. Friction and wear characteristics of these hybrid ceramic materials were tested with a micro tribe-tester where a reciprocating steel ball slid on a test material, and the tribological property was also evaluated with respect to both heat-curing temperature and tile time. Test results generally showed that hybrid ceramic materials modified by epoxy-silane compounds had a low friction compared to others. And the higher heat-curing temperature and the longer heat treatment time resulted in the higher friction and the lower wear. IR spectroscopic analyses revealed that it was caused mainly by the increased metal oxide content in hybrid ceramics when the heat-curing temperature was over $320^{\circ}C$.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.3
• /
• pp.128-132
• /
• 2004

The perovskite ferroelectric materials of the PZT, SBT and BST series will attract much attention for application to ULSI devices. Among these materials, the BST ($Ba_0.6$$Sr_0.4$/$TiO_3$) is widely considered the most promising for use as an insulator in the capacitors of DRAMS beyond 1 Gbit and high density FRAMS. Especially, BST thin films have a good thermal-chemical stability, insulating effect and variety of Phases. However, BST thin films have problems of the aging effect and mismatch between the BST thin film and electrode. Also, due to the high defect density and surface roughness at grain boundarys and in the grains, which degrades the device performances. In order to overcome these weakness, we first applied the chemical mechanical polishing (CMP) process to the polishing of ferroelectric film in order to obtain a good planarity of electrode/ferroelectric film interface. BST ferroelectric film was fabricated by the sol-gel method. And then, we compared the surface characteristics before and after CMP process of BST films. We expect that our results will be useful promise of global planarization for FRAM application in the near future.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.1030-1035
• /
• 2001

Strontium barium niobate, (Sr$\sub$0.5/Ba$\sub$0.5/Nb$_2$O$\sub$6/), thin films of various composition were prepared by the sol-gel method. Solution derived from acetate powders and niobium ethoxide in a mixture of acetic acid, ethylene glycol and 2-methoxyehanol was spin-coated onto bare silicon, Pt-coated silicon and fused silica substrates. Processing parameters were optimized to develop stable solutions which yielded films with relatively low crystallization temperatures. It was determined that ethylene glycol was a necessary component of the solution to increase stability against precipitation and to decrease the crystallization temperature of the films as confirmed by XRD and FT-IR analyses.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.175-178
• /
• 1998

LiMn$_2$O$_4$-based spinels has been studied extensively as positive electrode materials for rechargeable lithium and lithium ion batteries. We describe here that LiMn$_2$O$_4$ cathode active materials is preparated by sol-gel process using water as solvent, which often yields inorganic oxides of excellent phase purity and well-controlled stoichiometry. Using this process, it has been possible to synthesize phase-pure crystalline spinel LiMn$_2$O$_4$ by calcining the appropriate precursors in air at 80$0^{\circ}C$ for several hours. The influence of different time have also been explored. LiMn$_2$O$_4$ preparated in the present study exhibit the single phase of cubic and active reaction at 400 ~ $600^{\circ}C$. Electrochemical studies show that the this method- synthesized materials appear to present reversible oxidation and reduction reactions at 3.0V ~ 4.5V and cycle stability during 50 cycle.

• Korean Chemical Engineering Research
• /
• v.48 no.4
• /
• pp.428-433
• /
• 2010

Waterborne polyurethane(WPU) was synthesized from isophorone diisocyanate(IPDI), poly(tetramethylene glycol)(PTMG), dimethylol propionic acid(DMPA), triethylamine(TEA), ethylenediamine(EDA) and 3-aminopropyl triethoxysilane(APS) as a coupling agent. Subsequently, WPU/silica nanocomposites with different silica contents(0 to 8 wt%) were prepared by performing sol-gel reactions with tetraethylorthosilicate in the WPU matrix. The average particle size of the nanocomposite solutions increased with increasing TEOS content. Also, the prepared nanocomposites showed better thermal stability than pure WPU.

• Tribology and Lubricants
• /
• v.18 no.5
• /
• pp.324-332
• /
• 2002

In order to enhance the thermal stability of binder materials of bonded type solid lubricants, several metal-alkoxide based sol-gel materials such as methyltrimethoxysilane(MTMOS), titaniumisopropoxide$(Ti(Opr^i)_4),$ zirconiumisopropoxide $(Zr(Opr^i)_4)$ and aluminumbutoxide$(Al(Obu^t)_4)$ were chemically modified by epoxy-, acrylic- and fluoro-silane compounds, respectively. Friction and wear characteristics of these hybrid ceramic materials were tested with a micro tribo-tester, and evaluated with respect to both heat-curing temperature and the time. Test results generally showed that hybrid ceramic materials modified by epoxy-silane compounds had a low friction compared to others. And the higher het-curing temperature and the longer heat treatment time resulted in the higher friction and the lower wear. IR spectroscopic analyses revealed that these results were caused mainly by the increased metal oxide content in hybrid ceramics when the heat-curing temperature was over $320^{\circ}C.$

• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3123-3127
• /
• 2010

A highly sensitive electrochemical detection method for dopamine (DA) has been developed by relying on a multiwalled carbon nanotube (CNT)-sol-gel titania-Nafion composite film modified glassy carbon (GC) electrode. The CNT-titania-Nafion/GC electrode exhibited excellent electrocatalytic activity towards DA. Therefore, the CNT-titania-Nafion/GC electrode showed improved voltammetric and amperometric responses for DA compared to those obtained with both titania-Nafion/GC and Nafion/GC electrodes. The CNT-titania-Nafion/GC electrode gave a linear response ($R^2$ = 0.999) for DA from $0.5\;{\mu}M$ to 0.5 mM with a detection limit (S/N = 3) of $0.1\;{\mu}M$ and a good sensitivity of 150 mA/M while other electrodes such as CNT-Nafion/GC, titania-Nafion/GC, and a bare GC gave a sensitivity of 89, 39, and 36 mA/M, respectively. Besides, the CNT-titania-Nafion/GC electrode displayed very fast response time within 2 s. The modified electrode showed good selectivity against ascorbic acid. The modified electrode showed good stability and reproducibility. The CNT-titania-Nafion/GC electrode was applied to the determination of DA in urine and serum samples.

• Journal of the Korean Applied Science and Technology
• /
• v.16 no.4
• /
• pp.317-322
• /
• 1999

Transparent films were prepared using the sol-gel process by mixing TEOS with PVA solution that was solved in EtOH and distilled water homogeneously. HCl, $CH_3COOH$ and $NH_4OH$ were used as catalysts of the sol-gel process, and for improving the flexibility of films glycerol was used as plasticizer. In case of each catalyst, transparency and tensile strength were increased, and glass transition temperature (Tg) was shifted to higher temperature with increasing TEOS ratio. Also, in case of adding the plasticizer, the flexibility of films was increased. On the contrary, transparency, thermal stability and tensile strength were decreased with increasing HCl and $NH_4OH$ ratio. Also, the range of being made of film type was expanded when $CH_3COOH$ was used than HCl and $NH_4OH$.

• Applied Chemistry for Engineering
• /
• v.16 no.6
• /
• pp.822-826
• /
• 2005

Colloidal Silica (CS)/methyltrimethoxysilane (MTMS) and CS/MTMS/epoxysilane (ES) sol solutions were prepared using various synthesizing parameters such as reaction time and types of CS and silane. In order to understand their physical and chemical properties, sol-gel coating films on glass were fabricated. In the case of the CS/MTMS sol, the coating films had high contact angle and more enhanced flat surface than the CS/MTMS/ES sol. In the case of thermal stability, thermal degradation of the CS/MTMS and CS/MTMS/ES coating films did not occur up to $550^{\circ}C$ and $440^{\circ}C$, respectively. The coating films prepared from the CS/MTMS sol were thicker than those of the CS/MTMS/ES sol. In addition, the coating films prepared from single CS were thicker than those of mixed CS. Hardness of the coating films prepared from CS/MTMS increased by adding ES. In case of the mixed CS, the hardness decreased by adding ES.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.43 no.5
• /
• pp.555-566
• /
• 2023

In this study, a composite phase change material (CPCM) produced using the SOL-GEL technique was developed as a thermal energy storage medium for low-temperature applications. Tetradecane and activated carbon (AC) were used as the core and supporting materials, respectively. The tetradecane phase change material (PCM) was impregnated into the porous structure of AC using the vacuum impregnation method, and a thin layer of silica gel was coated on the prepared composite using the SOL-GEL process, where tetraethyl orthosilicate (TEOS) was used as the silica source. The thermal performance of the CPCM was analysed using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). DSC results showed that the pure tetradecane PCM had melting and freezing temperatures of 6.4℃ and 1.3℃ and corresponding enthalpies 226 J/g and 223.8 J/g, respectively. The CPCM exhibited enthalpy of 32.98 J/g and 27.7 J/g during the melting and freezing processes at 7.1℃ and 2.4℃, respectively. TGA test results revealed that the AC is thermally stable up to 500℃, which is much higher than the decomposition temperature of the pure tetradecane, which is around 120℃. Moreover, in the case of AC-PCM and CPCM thermal degradation started at 80℃ and 100℃, respectively. The chemical stability of the CPCM was studied using Fourier-transform infrared (FT-IR) spectroscopy, and the results confirmed that the developed composite is chemically stable. Finally, the surface morphology of the AC and CPCM was analysed using scanning electron microscopy (SEM), which confirmed the presence of a thin layer of silica gel on the AC surface after the SOL-GEL process.