• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.6
• /
• pp.689-702
• /
• 2019

This paper deals with the verification of the functions about mining robot, which is the system for developing deep seabed resources by applying V&V(verification and validation). In order to overcome water pressure of 500 bar and to travel on soft ground, and to operate in deep sea environment with bad conditions, it is necessary to develop a robot that can satisfy various deepsea conditions. A mining robot has been developed based on simulation based design and Multidisciplinary design optimization. In order to verify the developed robot, lab test and real sea test should be performed for various marine environment conditions. There are too many requirements to consider, such as space, time, cost, personnel, and environment to do performance test. So it is costly and time consuming for developing robot. In order to solve this problems, V&V technique was applied to mining robot. The stages of mining robot design, fabrication and commission were verified.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.203-208
• /
• 2003

In this paper, gait generation algorithm based on Linear Inverted Pendulum Mode is extended considering that the terrain is uncertain and flexible. Deformation of the soft terrain by the weight of the biped robot is taken into account to design the desired motion of the swing leg. Landing time disagreement caused by dynamics of the robot is also considered and a method to adjust gait is proposed. Results of numerical simulation show the effectiveness of the proposed method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.8
• /
• pp.1250-1258
• /
• 1997

This paper reports on the development of a new foot for a quadrupedal jointed-leg type walking robot. The foot has 2 toes, one at the front and the other at the rear side, for stable landing on uneven ground by point contact. The toes can move up and down independantly, guided by double-wishbone shaped parallel links which enable the lower leg to rotate with respect to a remote center on the ground surface. The motion of each toe is damped by a hydropneumatic shock absorber integrated in the foot in order to absorb the dynamic landing shock. Furthermore, the new foot can reduce the maximum hip joint drive torque by shortening the moment arm length between the hip joint and the landing force vector on the ground. Intensive experiments were carried out in this study by using a one-leg walking model to investigate the soft landing performance of the foot which could be hardly offered by conventional robot feet such as a flat plate with a gimbal type ankle joint. And it was confirmed that the hip joint torque of the leg walking on the flat surface could be reduced remarkably by using the new foot.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.4
• /
• pp.509-515
• /
• 2010

In this paper, the mechanism that can walk efficiently in wet land or sand area is proposed. A vision camera is attached to the mechanism, which makes a kind of biologically inspired robot for coast guard. This visionary information enables the biologically inspired robot to react in peripheral environment by a soft-computing algorithm. In addition, the biologically inspired robot can achieve the mission appointed by a programmer connecting with outside, based on RF and Blue-tooth communication module. Therefore, the purpose of this research is the implementation of the biologically inspired robot that can operate most adaptively in sand and wet surface based on Theo Jansen mechanism.

• Journal of Ocean Engineering and Technology
• /
• v.28 no.2
• /
• pp.152-159
• /
• 2014

KRISO(Korea Research Institute of Ships & Ocean Engineering) designed and manufactured a pilot mining robot called "MineRo" in 2012. MineRo is composed of four track modules. In general, much time and money are needed for deep-sea tests. Therefore, a numerical analysis to predict the dynamic behaviors has to be performed before a deep-sea test. In the numerical analysis, the information about the mining robot and soil properties are the most important factors to analyze the driving performance and dynamic response of MineRo. A terra-mechanics model of extremely cohesive soft soil is implemented in the form of the relationships between the normal pressure and sinkage, and between the shear stress and shear displacement. It is possible to acquire information about MineRo from the CAD model in the design phase. The Wong model is applied to the terra-mechanics model. This model is necessary to acquire many soil coefficients for a numerical analysis. However, in soil testing, the amount of soil property data obtained is limited. Moreover, it is difficult to analyze all of the cases for the many soil coefficients. In this paper, the dynamic behaviors of MineRo are analyzed according to the driving velocity, steering ratio, and variable extremely cohesive soft soil properties using a table of orthogonal arrays. The dynamic responses of MineRo are the turning radius, sinkage, and slip ratio. The relationships between the dynamic responses and variable soil properties are derived for MineRo.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.12 no.5
• /
• pp.331-341
• /
• 2017

This paper presents the sea-trial results of Crabster CR6000 which is a deep-sea walking robot developed by KRISO in 2016. Crabster CR6000 is designed to inspect deep-sea environment rejecting the disturbance on the silent and calm abyssal area. The sea-trial was conducted at the East Sea and the Philippine Sea on December 2016. The Crabster CR6000 undocked successfully from the Shuttle after touchdown on the sea-bed and walked out on the soft sediment soil of the 4,743m seafloor at the fourth diving in the Philippine Sea. The advanced technologies and capabilities of CR6000 were verified from the operational and functional test conducted in the sea-trial. The experimental data acquired from the sea-trial were summarized and the first experience of the deep-sea walking robot was presented in this paper.

• The Journal of Korea Robotics Society
• /
• v.15 no.4
• /
• pp.375-384
• /
• 2020

Today's robots consist of many hardware and software subsystems, depending on the functions needed for specific tasks. Integration of subsystems can require a great deal of effort, as both the communication method and protocol of the subsystem can vary. This paper proposes an expandable robotic system in which all subsystems are integrated under Robot Operation System (ROS) framework. To achieve this, the paper presents a software library, ROS_M, developed to implement the TCP/IP-based ROS communication protocol in different control environments such as MCU and RT kernel based embedded system. Then, all the subsystem including hardware can use ROS protocol consistently for communication, which makes adding new software or hardware subsystems to the robotic system easier. A latency measurement experiment reveals that the system built for loop control can be used in a soft real-time environment. Finally, an expandable mobile manipulator robot is introduced as an application of the proposed system. This robot consists of four subsystems that operate in different control environments.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.2
• /
• pp.60-69
• /
• 2010

Lookup-Table (LUT) based fuzzy controller for obstacle avoidance enhances operations faster in multiple obstacles environment. An LUT based fuzzy controller with Positive/Negative (P/N) fuzzy rule base consisting of 18 rules was introduced in our paper$^1$ and this paper shows a 50-rule P/N fuzzy controller for enhancing performance in obstacle avoidance. As a rule, the more rules are necessary, the more buffers are required. This paper suggests LUT sharing method in order to reduce LUT buffer size without significant degradation of performance. The LUT sharing method makes buffer size independent of the whole fuzzy system's complexity. Simulation using MSRDS(MicroSoft Robotics Developer Studio) evaluates the proposed method, and in order to investigate its performance, experiments are carried out to Pioneer P3-DX in the LabVIEW environment. The simulation and experiments show little difference between the fully valued LUT-based method and the LUT sharing method in operation times. On the other hand, LUT sharing method reduced its buffer size by about 95% of full valued LUT-based design.

• Composites Research
• /
• v.33 no.2
• /
• pp.50-54
• /
• 2020

Soft robotics and wearable devices require large motions and flexibility. In this regard, there is a demand for developing stretchable strain sensors which can be attached to the soft robots and wearable devices. In this work, we fabricated stretchable and electrically conductive composite fibers by combining polyurethane (PU) and silver nanoflowers (AgNFs). The PU/AgNF composite fibers showed the change of the resistance as a function of the applied strain, demonstrating the potential for stretchable strain sensors in soft robotics and wearable devices. The mechanical and electrical characteristics of the composite fibers were measured and analyzed to use the composite fibers for stretchable strain sensors.

• Journal of Biomedical Engineering Research
• /
• v.31 no.3
• /
• pp.227-233
• /
• 2010

This study analyzed performance according to kick point and stiffness of Soft-$golf^{TM}$ shaft. This research team developed soft-$golf^{TM}$ as a new fusion sports with similar motions with golf and it can be learned safely for all age groups in 2002. The head of Soft-$golf^{TM}$ club is made of zinc alloy and has a mesh or a grid structure, and shaft uses carbon graphite to reduce the total weight of the club. To improve carry distance and to assure consistency of a ball during Soft-$golf^{TM}$ swing, this study manufactured shaft with various kick points (low, middle and high) and stiffness (stiff, regular, lady, morelady) and analyzed a swing motion with characteristics of each shaft presented in a dynamic condition such as a ball's speed, a head's torsion angle and a ball's deviation with ProAnalyst program through a high-speed camera taking pictures using a swing machine robot system(Robo-7). From all of the results, this study determined an appropriate shaft of Soft-$golf^{TM}$.