• Transactions on Electrical and Electronic Materials
• /
• v.17 no.2
• /
• pp.104-108
• /
• 2016

To research the correlation between oxygen vacancy and the electrical characteristics of ZTO, which is made by using a target mixed ZnO:SnO₂=1:1, the ZnO, SnO₂ and ZTO were analyzed by PL, XPS, XRD patterns and electrical properties. It was compared with the electron orbital spectra of O 1s in accordance with the electrical characteristics of ZnO, SnO₂ and ZTO. The electrical characteristics of ZTO were improved by increasing the annealing temperatures, due to the high degree of crystal structures at a high temperature, and the physical properties of ZTO was similar to that of ZnO. The amorphous structure of SnO₂ was increased with increasing the temperature. The Schottky contact of oxide semiconductors was formed using the depletion region, which is increased by the electron-hole combination due to the annealing processes. ZnO showed the Ohmic contact in spite of a high annealing temperature, but SnO₂ and ZTO had Schottky contact. As such, it was confirmed that the electrical properties of ZTO are affected by the molecules of SnO₂.

• Journal of Powder Materials
• /
• v.29 no.5
• /
• pp.357-362
• /
• 2022

The low-temperature sinterability of TiO₂-CuO systems was investigated using a solid solution of SnO₂. Sample powders were prepared through conventional ball milling of mixed raw powders. With the SnO₂ content, the compositions of the samples were Ti_1-xSn_xO₂-CuO(2 wt.%) in the range of x ≤ 0.08. Compared with the samples without SnO₂ addition, the densification was enhanced when the samples were sintered at 900℃. The dominant mass transport mechanism seemed to be grain-boundary diffusion during heat treatment at 900℃, where active grain-boundary diffusion was responsible for the improved densification. The rapid grain growth featured by activated sintering was also obstructed with the addition of SnO₂. This suggested that both CuO as an activator and SnO₂ dopant synergistically reduced the sintering temperature of TiO₂.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.2
• /
• pp.83-90
• /
• 2023

The β-Ga₂O₃ has the most thermodynamically stable phase, a wide band gap of 4.8~4.9 eV and a high dielectric breakdown voltage of 8MV/cm. Due to such excellent electrical characteristics, this material as a power device material has been attracted much attention. Furthermore, the β-Ga₂O₃ has easy liquid phase growth method unlike materials such as SiC and GaN. However, since the grown pure β-Ga₂O₃ single crystal requires the intentionally controlled doping due to a low conductivity to be applied to a power device, the research on doping in β-Ga₂O₃ single crystal is definitely important. In this study, various source powders of un-doped, Sn 0.05 mol%, Sn 0.1 mol%, Sn 1.5 mol%, Sn 2 mol%, Sn 3 mol%-doped Ga₂O₃ were prepared by adding different mole ratios of SnO₂ powder to Ga₂O₃ powder, and β-Ga₂O₃ single crystals were grown by using an edge-defined Film-fed Growth (EFG) method. The crystal direction, crystal quality, optical, and electrical properties of the grown β-Ga₂O₃ single crystal were analyzed according to the Sn dopant content, and the property variation of β-Ga₂O₃ single crystal according to the Sn doping were extensively investigated.

• Journal of Sensor Science and Technology
• /
• v.33 no.2
• /
• pp.105-111
• /
• 2024

In this study, the H₂S gas sensing characteristics were evaluated using surface-modified SnO₂ microparticles by tip sonication. The surface-modified SnO₂ microparticles were synthesized using the following sequential process. First, bare SnO₂ microparticles were synthesized via a hydrothermal method. Then, the surfaces of bare SnO₂ microparticles were modified with Ti nanoparticles during tip sonication. The sensing characteristics of SnO₂ microparticles modified with Ti were systematically investigated in the range of 100-300℃, compared with the bare SnO₂ microparticles. In this study, we discuss in detail the improved H₂S sensing characteristics of SnO₂ microparticles via Ti nanoparticle modification.

• Journal of Powder Materials
• /
• v.31 no.2
• /
• pp.146-151
• /
• 2024

Pure SnO₂ has proven very difficult to densify. This poor densification can be useful for the fabrication of SnO₂ with a porous microstructure, which is used in electronic devices such as gas sensors. Most electronic devices based on SnO₂ have a porous microstructure, with a porosity of > 40%. In pure SnO₂, a high sintering temperature of approximately 1300℃ is required to obtain > 40% porosity. In an attempt to reduce the required sintering temperature, the present study investigated the low-temperature sinterability of a current system. With the addition of TiO₂, the compositions of the samples were Sn_1-xTi_xO₂-CoO(0.3wt%)-CuO(2wt%) in the range of x ≤ 0.04. Compared to the samples without added TiO₂, densification was shown to be improved when the samples were sintered at 950℃. The dominant mass transport mechanism appears to be grain-boundary diffusion during heat treatment at 950℃.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.3
• /
• pp.201-207
• /
• 2023

Eu³⁺-doped SnO² (SnO²:Eu³⁺) phosphor thin films were grown on quartz substrates by radio-frequency magnetron sputtering. The deposition temperature was varied from 100 to 400 ℃. The X-ray diffraction patterns showed that all the thin films had two mixed phases of SnO₂ and Eu₂Sn₂O₇. The 880 nmthick SnO²:Eu³⁺ thin film grown at 100 ℃ exhibited numerous pebble-shaped particles. The excitation spectra of SnO²:Eu³⁺ thin films consisted of a strong and broad peak at 312 nm in the vicinity from 250 to 350 nm owing to the O^2--Eu3+ charge transfer band, irrespective of deposition temperature. Upon 312 nm excitation, the SnO²:Eu³⁺ thin films showed a main emission peak at 592 nm arising from the ⁵D₀→⁷F₁ transition and a weak 615 nm red band originating from the ⁵D₀→⁷F₂ transition of Eu³⁺. As the deposition temperature increased, the emission intensities of two bands increased rapidly, approached a maximum at 100 ℃, and then decreased slowly at 400 ℃. The thin film deposited at 200 ℃ exhibited a band gap energy of 3.81 eV and an average transmittance of 73.7% in the wavelength range of 500-1100 nm. These results indicate that the luminescent intensity of SnO²:Eu³⁺ thin films can be controlled by changing the deposition temperature.

• Journal of the Korean Chemical Society
• /
• v.41 no.4
• /
• pp.175-179
• /
• 1997

Luminescence of $Eu^{3+}$ has been studied in $Sr_{2-2x}Eu_xK_xSnO_4$ with two-dimensional $K_2NiF_4$ structure. The $^5D_o$ → $^7F_o$$Eu^{3+}$ ion represents the J=0 → J=0 transition which is forbidden by a Judd-Ofelt selection rule for electric dipole transition in 4f shell of $Eu^{3+}$ ions. However, the emission line of $^5D_o$ → $^7F_o$$Eu^{3+}$ emission spectra of Sr2-2xEuxKxSnO4$Sr_{2-2x}Eu_xK_xSnO_4$structure around $Eu^{3+}$ ions.

• Korean Journal of Materials Research
• /
• v.12 no.5
• /
• pp.347-352
• /
• 2002

A transparent dielectric of the $PbO-B_2O_3-SiO_2-A1_2O_3$ system which was a low melting glass has been used for PDP (Plasma Display Panel), but it has a problem which is a reaction to be occurred between a transparent dielectric layer and electrodes (Ag, ITO) after firing. This research was conducted for ion migration of $Ag^+\$ and $Sn^ {2+}$ during firing three different frits of low melting glass. The result showed that yellowing phenomena occurred through a chemical reaction between $Ag^+\$and $Sn^ {2+}$ at 550~58$0^{\circ}C$ for 20~60 min. In addition, it was confirmed that the migration of $Sn^{2+}$ from ITO electrode made a strong effect on the yellowing phenomena.

• Journal of Sensor Science and Technology
• /
• v.31 no.5
• /
• pp.348-352
• /
• 2022

Hydrogen gas (H₂) which is odorless, colorless is attracting attention as a renewable energy source in varions applications but its leakage can lead to disastrous disasters, such as inflammable, explosive, and narcotic disasters at high concentrations. Therefore, it is necessary to develop H₂ gas sensor with high performance. In this paper, we confirmed that H₂ gas detection ability of SnO₂ based H₂ gas sensor along with thermal treatment effect of SnO₂. Proposed SnO₂ based H₂ gas sensor is fabricated by MEMS technologies such as photolithgraphy, sputtering and lift-off process, etc. Deposited SnO₂ thin films are thermally treated in various thermal treatement temperature in range of 500-900 ℃ and their H₂ gas detection ability is estimatied by measuring output current of H₂ gas sensor. Based on experimental results, fabricated H₂ gas sensor with SnO₂ thin film which is thermally treated at 700 ℃ has a superior H₂ gas detection ability, and it can be expected to utilize at the practical applications.

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.639-642
• /
• 2009

The research was performed to find out the optimum firing condition for the $SnO_2-TiO_2-V_2O_5$ system yellow pigment. The pigment based on $SnO_2-V_2O_5$ system showed very intense yellow color and it was used widely in ceramics industry. Synthesized pigment, with partial substitutions of $SnO_2\;by\;TiO_2$, was fired at $1300{^{\circ}C}$ soaking 1h and it showed bright yellow color. $SnO_2-TiO_2-V_2O_5$ system was very more intensive changes in yellow color by colorimetric value $b^*$ than $SnO_2-V_2O_5$ system. Synthesized yellow pigments were characterized by X-ray diffraction (XRD), FT-IR, and UV-vis spectroscopy. The best composition for yellow pigment was 93:7:0.5(mole%) for $SnO_2-V_2O_5-TiO_2$. The measurement of CIE $L^*a^*b^*$ of pigment was $L^*(78.82),\;a^*(-4.88)\;and\;b^*$(59.25).