• Korean Journal of Metals and Materials
• /
• v.47 no.8
• /
• pp.500-507
• /
• 2009

Pb-free solder has recently been used in electronics in efforts to meet environmental regulations, and a number of Pb-free solder alloy choices beyond the near-eutectic SnAgCu solder are now available. With increased demand for thin and portable electronics, the high cost of alloys containing significant amounts of silver and their poor mechanical shock performance have spurred the development of low Ag SnAgCu solder, which provides improved mechanical performance at a reasonable cost. Although low Ag SnAgCu solder exhibits significantly higher fracture resistance under high-strain rates, little thermal fatigue data exist for this solder. Therefore, it is necessary to investigate thermal fatigue reliability of low Ag SnAgCu solder under variation of thermal stress in order to allow its implementation in electronic products with high reliability requirements. In this study, the reliability of Sn0.3Ag0.7Cu(SAC0307), a low Ag solder alloy, is discussed and compared with that of Sn3Ag0.5Cu(SAC305). Three sample types and six samples size are evaluated. Mechanical properties and microstructure of the solder joint are investigated under thermal shock cycles. It was observed that the mechanical strength of SAC0307 dropped slightly with thermal cycling relative to that of SAC305. This reveals that the failure mode of SAC0307 is different from that SAC305 under this critical condition.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.211-214
• /
• 2007

Sn-0.3Ag-0.7Cu 조성의 젖음 특성과 반응 특성을 Sn-1.0Ag-0.5Cu 및 Sn-3.0Ag-0.5Cu 합금의 결과와 비교, 분석하였다. 또한 Sn-0.3Ag-0.7Cu 조성의 용융 및 응고 특성을 DSC로 측정하고, 인장시험을 통한 stress-strain curve를 관찰하였다. 아울러 할로겐 함유량이 많은 플럭스를 사용하여 Sn-0.3Ag-0.7Cu 조성의 젖음 특성을 향상 시킬 수 있는지를 조사하였으며, Sn-0.3Ag-0.7Cu 조성에 미량의 In을 첨가하여 젖음 특성의 개선 정도를 분석하였다. 그 결과 할로겐 함유량이 높은 플럭스를 사용한 경우보다 미량의 In을 첨가한 경우에서 wettability의 향상을 보다 효과적으로 유도할 수 있음을 관찰할 수 있었다.

• Journal of Climate Change Research
• /
• v.7 no.3
• /
• pp.231-236
• /
• 2016

Electrocatalytic reduction can produce useful chemicals and fuels such as carbon monoxide, methane, formate, aldehydes, and alcohols using carbon dioxide, the green house gas, as a reactant through the supply of electrical energy. In this study, tin-lead (Sn-Pb) alloy electrodes are fabricated by electrodeposition on a carbon paper with different alloy composition and used as cathode for electrocatalytic reduction of carbon dioxide into formate in an aqueous system. The prepared electrodes are measured by Faradaic efficiency and partial current density for formate production. Electrocatalytic reduction experiments are carried out at -1.8 V (vs. Ag/AgCl) using H-type cell under ambient temperature and pressure and the gas and liquid products are analyzed by gas chromatograph and liquid chromatograph, respectively. As results, the Sn-Pb electrodes show higher Faradaic efficiency and partial current density than the single metal electrode. The Sn-Pb alloy electrode which have Sn:Pb molar ratio=2:1, shows the highest Faradaic efficiency of 88.7%.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.04a
• /
• pp.81-86
• /
• 2000

To evaluate the possibility of the partial melting soldering. wettability of partial melted solders was measured using wetting balance. Off eutectic Sn-Pb allows are wettable in their partial melting zone. Especially, Pb rich alloys showed excellent wettability while wettability of Sn rich alloys were adequate or poor. It is found that wettability increases over $200^{\circ}C$ regardless of composition liquid fraction and phases of the original alloy Sn-7Ag alloy showed good wettability in their partial melting zone, while Sn-65Bi alloy was non-wettable under their melting points.

• The Journal of Korean Academy of Prosthodontics
• /
• v.21 no.1
• /
• pp.9-26
• /
• 1983

In order to investigate the biocompatibility of silver-palladium alloys, gingival fibroblast was obtained from a healthy human gingival and cultured in MEM medium with the addition of silverpalladium alloys. Four different mixture of silver-palladium alloys comprising of Ag-Pd-Au, Ag-Pd-In and Ag-Sn were tested. Results were assessed by calculating the cell multiplication rate per millimeter of medium and morphological changes in cells were also observed and noted.The obtained results were as follows; 1. Ag-Pd-Au alloy was indicated to be most biocompatible with gingival fibroblast. Also there was a decrease in cytotoxicity of the alloy as the concentration of gold increased. 2. Ag-Pd alloy showed a decrease in cell multiplication rate as compared to Ag-Pd~Au alloy. 3. Silver-palladium alloy supplemented with Indium increased the cell multiplication rate. 4. Among the alloys tested, Ag-Sn alloy was indicated to be the most cytotoxic and the least biocompatible with human gingival fibroblast.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.139-141
• /
• 2006

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.5
• /
• pp.332-337
• /
• 2015

We have studied the effects of Ag on the characteristics of $Sn_{60}Pb_{40}Ag_x$ (wt%) solder for photovoltaic ribbon. Ag atoms in the solder formed an alloy phase of $Ag_3Sn$ after reacting with some part of Sn atoms, while they did not react with Pb atoms, but decreased the mean size of Pb solid phase. The enhancement of peel strength between solar cell and ribbon is an important part in the developments of long-lifespan solar module. The peel strength of the solder ribbon of $Sn_{60}Pb_{40}$ (wt%) was $169N/mm^2$, and it was largely enhanced by adding a small amount of Ag atoms. The maximum peel strength was $295N/mm^2$ in the solder ribbon of $Sn_{60}Pb_{40}Ag_2$ (wt%). This result is caused by the high binding energy of 162.9 kJ/mol between Ag atoms in the solder and Ag atoms in Ag sheet.

• Proceedings of the KWS Conference
• /
• 2001.05a
• /
• pp.268-270
• /
• 2001

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1999.05a
• /
• pp.123-123
• /
• 1999

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.2
• /
• pp.119-125
• /
• 2017

We have studied the effects of Ag on the characteristics of $Sn_{43}Bi_{57}Ag_x$(wt%) lead-free solders for photovoltaic ribbon. Ag atoms in the solder formed an alloy phase of Ag3Sn after reacting with some part of Sn atoms, while they did not react with Bi atoms, but decreased the mean size of Bi solid phase and the thickness of solder. When Ag atoms of 3.0 wt% was added to eutectic $Sn_{43}Bi_{57}$(wt%) solder, it showed the optimally useful results that the peel strength of photovoltaic ribbon greatly increased and the sheet resistance of the solder decreased. In the meanwhile, the eutectic $Sn_{43}Bi_{57}$(wt%) solder showed a low melting temperature of $138.9^{\circ}C$, and showed a very similar result regardless of the added amount of Ag atoms.