• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.54-56
• /
• 2005

Ultrasonic soldering using of Si-wafer to FR-4 PCB atroom temperature was investigated. Sn3.5Ag foil rolled $100{\mu}m$ was used for solder. The UBM of Si-die was Cu/ Ni/ Al from top to bottom and its thickness was $0.4{\mu}m$, $0.4{\mu}m$, $0.3{\mu}m$ respectively. Pad on FR-4 PCB comprised of Au/ Ni/ Cu from top to bottom and its thickness was $0.05{\mu}m$, $5{\mu}m$, $18{\mu}m$ respectively. The ultrasonic soldering time was changed from 0.5sec to 3.0sec and its power 1400W. As experimental result, reliable bond joint by ultrasonic at room temperature was obtained. The shear strength increased with soldering time up to 2.5 sec. That means at 2.5sec, the shear strength showed maximum rate of 65.23N. The strength decreased to 33.90N at 3.0 sec because the cracks generated along the intermetallic compound between Si-wafer and Sn-3.5mass%Ag solder. intermetallic compound produced by ultrasonic between the solder and the Si-die was $(Cu, Ni)_{6}Sn_{5}$ and the intermetallic compound between solder and pad on FR-4 was $(Ni, Cu)_{3}Sn_{4}$.

• 한국표면공학회지
• /
• 제54권3호
• /
• pp.119-123
• /
• 2021

SnO₂ single layer and SnO₂/Ag/SnO₂ (SAS) tri-layered films were deposited on the glass substrate by RF and DC magnetron sputtering at room temperature and then the effect of Ag interlayer on the opto-electrical performance of the films were considered. As deposited SnO₂ films show a visible transmittance of 85.5 % and a sheet resistance of 1.2×10⁴ Ω/□, the SAS films with a 15 nm thick Ag interlayer show a lower resistance of 18.8 Ω/□ and a visible transmittance of 70.6 %, respectively. The figure of merit based on the optical transmittance and sheet resistance revealed that the Ag interlayer in the SnO₂ films enhances the opto-electrical performance without substrate heating or annealing process.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2006년도 춘계학술발표대회 및 제10회 신소재 심포지엄 논문개요집
• /
• pp.25.2-25.2
• /
• 2006

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1995년도 특별강연 및 추계학술발표 개요집
• /
• pp.110-112
• /
• 1995

Initial solder joint strengths of various solder pastes, such as Sn-Pb(63-37wt%), Sn-In(52-48wt%), Sn-In-Ag(77.5-20-2.5wt%), and Sn-Ag(96.5-3.5wt%) has been studied. A system that can control the solder joint interface temperature during bonding process was also desined and implemented to improve solder joint integrity.

• 한국표면공학회지
• /
• 제52권3호
• /
• pp.145-149
• /
• 2019

Transparent and conductive ZnO/Ag/SnO2 (ZAS) tri-layer films were deposited onto glass substrates at room temperature by using radio frequency (RF) and direct current (DC) magnetron sputtering. The thickness values of the ZnO and $SnO_2$ thin films were kept constant at 50 nm and the value for Ag interlayer was varied as 5, 10, 15, and 20 nm. In the XRD pattern the diffraction peaks were identified as the (002) and (103) planes of ZnO, while the (111), (200), (220), and (311) planes could be attributed to the Ag interlayer. The optical transmittance and electrical resistivity were dependent on the thickness of the Ag interlayer. The ZAS films with a 10 nm thick Ag interlayer exhibited a higher figure of merit than the other ZAS films prepared in this study. From the observed results, a ZAS film with a 10 nm thick Ag interlayer was believed to be an alternative transparent electrode candidate for various opto-electrical devices.

• 한국재료학회지
• /
• 제17권2호
• /
• pp.91-95
• /
• 2007

Electromigration characteristics of Sn-3.5Ag flip chip solder bump were analyzed using flip chip packages which consisted of Si chip substrate and electroplated Cu under bump metallurgy. Electromigration test temperatures and current densities peformed were $140{\sim}175^{\circ}C\;and\;6{\sim}9{\times}10^4A/cm^2$ respectively. Mean time to failure of solder bump decreased as the temperature and current density increased. The activation energy and current density exponent were found to be 1.63 eV and 4.6, respectively. The activation energy and current density exponent have very high value because of high Joule heating. Evolution of Cu-Sn intermetallic compound was also investigated with respect to current density conditions.

• 마이크로전자및패키징학회지
• /
• 제13권1호통권38호
• /
• pp.23-29
• /
• 2006

Si-웨이퍼와 FR-4 기판을 상온에서 초음파 접합한 후, 접합부의 신뢰성을 평가하였다. Si-웨이퍼 상의 UBM(Under Bump Metallization)은 위에서부터 Cu/ Ni/ Al을 각각 $0.4{\mu}m,\;0.4{\mu}m,\;0.3{\mu}m$의 두께로 전자빔으로 증착하였다. FR-4 기판위의 패드는 위에서부터 Au/ Ni/ Cu를 각각 $0.05{\mu}m,\;5{\mu}m,\;18{\mu}m$의 두께로 전해 도금하여 형성하였다. 접합용 솔도로는 Sn-3.5wt%Ag을 두께 $100{\mu}m$으로 압연하여 사용하였다. 시편의 초음파 접합을 위하여 초음파 접합 시간을 0.5초에서 3.0초까지 0.5초 단위로 증가시키면서 상온에서 접합하였으며, 이 때 출력은 1,400W로 하였다. 실험 결과, 상온 초음파 접합법에 의해 신뢰성 있는 'Si-웨이퍼/솔더/FR-4기판' 접합부를 얻을 수 있었다. 접합부의 전단 강도는 접합 시간에 따라 증가하여 접합 시간 2.5초에서 65N으로 가장 높게 측정되었다. 이 후 접합 시간 3.0초에서는 전단 강도가 34N으로 감소하였는데, 이는 초음파 접합시간이 과도해지면서 Si-웨이퍼와 솔더 사이의 계면을 따라 균열이 발생되었기 때문으로 판단된다. 초음파 접합에 의해 Si-웨이퍼와 솔더 사이에서 생성된 금속간 화합물은 ($(Cu,Ni)_{6}Sn_{5}$)으로 확인되었다.

• 한국전기전자재료학회논문지
• /
• 제20권6호
• /
• pp.561-565
• /
• 2007

Because of a good wear resistance and a stable contact resistance, Ag-CdO is widely used as electrical contact material. But, the Cd-oxide mainly exists as a coarse particle and adversely affected to environment. As a reason, $Ag-SnO_2$ alloy has been developed. The Sn-oxide maintains stable and fine particle even at high temperature. In order to investigate the effect of Misch metal (Mm) additional that affects the formation of the oxide and the formation of fine matrix Ag, we studied the microstructures and properties of Ag-Sn-In(-Mm) material fabricated by rapid solidification process. The experimental procedure were melting using high frequency induction, melt spinning, and internal oxidation. The Mm addition makes Ag matrix more fine than no Mm addition. The reason is that the addition of Misch metal decreased a latent heat of fusion of alloy, as a result the rapid solidification effect of alloy is increased. The maximum hardness shows at 0.3 wt%Mm. after that the hardness is decreased until 0.4 wt% Mm, but still larger than no Mm addition alloy. At 0.5 wt% Mm alloy, the precipitation of Misch metal causes a decrease of hardness than no Mm addition alloy.

• 마이크로전자및패키징학회지
• /
• 제8권4호
• /
• pp.25-33
• /
• 2001

Bi(0, 2.5, 4.8, 7.5, 10 wt%)가 첨가된 Sn-3.5Ag-xBi 합금을 주조 및 압연을 거쳐 준비하였다. 그 후, dog-bone형상의 시편의 안정한 미세 조직을 위해 열처리를 거친 후, 일정하중에 크리프 실험을 수행하였다. 2.5%Bi 첨가 합금의 경우, 크리프 저항성이 가장 우수하였으며, Bi가 더 첨가됨에 따라 크리프 저항성은 감소하였다. 합금의 응력 지수는 전형전인 전위 크리프에 의한 4를 나타내었으며, 10%Bi 시편의 경우, 입계 미끄러짐에 의한 2를 나타내었다. 0%Bi 합금의 경우, 연성 파괴 양상을 보인 반면, Bi 첨가 합금의 경우, 약간의 단면적 감소를 보이는 취성 파괴 양상을 보여주었다. 파단 시편의 미세 조직 관찰 결과, 응력축에 수직한 방향으로 기공이 관찰되었으며, 상당량의 입계 미끄러짐이 관찰되었다.

• 마이크로전자및패키징학회지
• /
• 제20권2호
• /
• pp.29-32
• /
• 2013

본 연구에서는 LED 리드프레임 상에 Sn-3.5wt%Ag를 무전해도금하여 표면 거칠기와 반사율을 측정하였다. Sn-3.5wt%Ag를 도금하기에 앞서 Sn-3.5wt%Ag 도금층의 반사율을 향상시키기 위하여 Cu 전해도금을 실시하였다. 도금 후 도금액의 교반속도와 온도가 도금층의 표면 거칠기와 반사율에 어떠한 영향을 미치는지 알아보기 위하여 각각의 도금인자에 대해서 표면 거칠기와 반사율을 측정하고자 하였다. 교반속도가 100~300 rpm으로 증가함에 따라 표면 거칠기는 0.513 ${\mu}m$에서 0.266 ${\mu}m$으로 감소하였으며, 반사율은 1.67 GAM에서 1.86 GAM으로 증가하였다. 또한 온도가 $25{\sim}45^{\circ}C$로 증가함에 따라 표면 거칠기는 0.507 ${\mu}m$에서 0.350 ${\mu}m$으로 감소하였으며, 반사율은 1.68 GAM에서 1.84 GAM으로 증가하였다.