• 한국품질경영학회:학술대회논문집
• /
• 한국품질경영학회 1998년도 The 12th Asia Quality Management Symposium* Total Quality Management for Restoring Competitiveness
• /
• pp.610-621
• /
• 1998

In parameter design introduced by Taguchi, we analyze a signal-to-noise(SN) ratio. The SN ratio is a function of the expected loss due to the variation of quality characteristic. In this paper, an easy way for developing SN ratios is presented, which can be used to several quality characteristics simultaneously in parameter design. To develop such multivariate SN ratios, the transformation method of the expected loss and combining techniques are employed. And the analysis of real empirical data for an application of the proposed method is also presented.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2013년도 춘계학술대회 논문집
• /
• pp.159-159
• /
• 2013

넓은 비표면적과 높은 전기전도성을 갖는 표면에 관능기가 도입된 RGO(reduced graphite oxide)를 modified Hummers method 와 thermal exfoliation 을 통해하여 합성하였으며 합성된 RGO를 PtSn alloy 촉매의 담지체로 도입하여 impregnation method를 통해 PtSn/RGO 시리즈 촉매를 합성하였다. XRD, SEM, TEM, XPS 분석을 통해 촉매의 특성을 분석하였고 methanol electrooxidation 활성을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.79-81
• /
• 2004

$TiO_2-SnO_2$ thin films are fabricated using sol-gel method. The thickness of thin films increase about $0.03{\sim}0.04{\mu}m$ every a dipping. The permittivity and dissipation factor of $TiO_2-SnO_2$ thin films decrease with increasing frequency. Thin films show semiconductive characteristics above $400^{\circ}C$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1433-1435
• /
• 2003

Ti-Sn sol is fabricated using sol-gel method. Initial viscosity of sol decreases with increasing HCl additive. Gelation of sol is retarded with increasing HCl additive. From the results of TG-DTA, the peaks of particular organics combustion do not occur because Sn sol is hydrolyzed sufficiently.

• 품질경영학회지
• /
• 제31권4호
• /
• pp.150-163
• /
• 2003

The purpose of this paper is to propose an interactive method using the concept of Signal­to­Noise (SN) ratios and cutting ranges for selecting the most preferred alternatives of Multiple­attribute Decision­Making(MADM) with the­smaller­the­better or the­larger­the­better characteristics. In this method the decision makers could make a grouping of attributes by their priorities. This research is based on the assumption of an equality between the attributes of MADM with the characteristics of Taguchi method. As a result, this interactive method could transform the characteristic value of Taguchi method into the size of SN ratios which are relatively easy to understand by decision makers.

• 한국재료학회지
• /
• 제26권9호
• /
• pp.468-471
• /
• 2016

$SnO_2:CNT$ thick films for gas sensors were fabricated by screen printing method on alumina substrates and were annealed at $300^{\circ}C$ in air. The nano $SnO_2$ powders were prepared by solution reduction method using tin chloride ($SnCl_2.2H_2O$), hydrazine ($N_2H_4$) and NaOH. Nano $SnO_2:CNT$ sensing materials were prepared by ball-milling for 24h. The weight range of CNT addition on the $SnO_2$ surface was from 0 to 10 %. The structural and morphological properties of these sensing material were investigated using X-ray diffraction and scanning electron microscopy and transmission electron microscope. The structural properties of the $SnO_2:CNT$ sensing materials showed a tetragonal phase with (110), (101), and (211) dominant orientations. No XRD peaks corresponding to CNT were observed in the $SnO_2:CNT$ powders. The particle size of the $SnO_2:CNT$ sensing materials was about 5~10 nm. The sensing characteristics of the $SnO_2:CNT$ thick films for 5 ppm $H_2S$ gas were investigated by comparing the electrical resistance in air with that in the target gases of each sensor in a test box. The results showed that the maximum sensitivity of the $SnO_2:CNT$ gas sensors at room temperature was observed when the CNT concentration was 8wt%.

• 한국건축시공학회지
• /
• 제14권6호
• /
• pp.505-513
• /
• 2014

본 연구에서는 전기화학적인 시험 및 CASS Test(염수분무시험)을 실시하여 중방식도장 시험체와 용융아연도금 시험체, Zn-Al 시험체와의 비교를 통해 Zn-Sn 금속용사의 방식 성능을 평가하였다. 시험 결과, 전기화학 시험을 통하여 Zn-Sn / Zn-Al 상온금속용사 시스템 공법의 방식원리는 방식전위에 의하여 확보되는 것을 확인하였으며 강구조물의 방식 공법으로서 상온금속용사 공법은 용융아연도금 공법과 중방식 도장공법과 비교하여 매우 우수한 방식성능을 가지고 있는 것이 CASS 시험을 통하여 검증되었다. 특히 Zn-Sn 금속용사와 Zn-Al 금속용사를 비교해본 결과 그 방식성이 현저하게 차이가 있지는 않았으나 Zn-Sn(65:35) 비율의 시험체가 가장 우수하였다. 또한 중방식 도장은 손상된 부분에서 현저하게 녹이 발생하고 도막이 박리되지만, Zn-Sn / Zn-Al 상온금속용사 시스템 공법은 갈바닉 희생방식에 의하여 매우 높은 부식 방지 특성을 가지고 있음을 확인 하였다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권11호
• /
• pp.511-516
• /
• 2002

$TiO_2-SnO_2$ thin films are fabricated using sol-gel method. In case the amount of water required hydrolysis smaller than that for stoichiometry, Ti sol forms clear sol which has normal chain structure. On the contrary, in case the amount of water required hydrolysis larger than that for stoichiometry, Ti sol forms suspended sol which has cluster structure. The thickness of thin films increase about $0.03{\sim}0.04{\mu}m$ every a dipping. The permittivity and dissipation factor of $TiO_2-SnO_2$ thin films decrease with increasing frequency. Thin films show semiconductive characteristics above $400^{\cric}C$.

• 한국표면공학회지
• /
• 제32권2호
• /
• pp.125-133
• /
• 1999

Fluorine-doped $SnO_2$ thin films were deposited on soda-lime glass substrates by reactive DC magnetron sputtering method. Crystallinity as well as electrical and optical properties of $SnO_2$ : F thin film were investigated as the variations of deposition conditions such as substrate temperature, DC Power, $O_2$ gas pressure, $SF_6$ gas pressure. $SnO_2$ : F thin film deposited with 5% $SF_6$ gas pressure showed electrical resistivities of $2.5\times10^{-3}$cm with the average optical transparency (about 80%) These electrical and optical properties were found to be related to the crystallinity of $SnO_2$ : F thin films.

• 한국산학기술학회논문지
• /
• 제19권9호
• /
• pp.536-542
• /
• 2018

이산화주석은 Rutile 구조를 갖는 Oxygen-Deficient n-type 반도체 물질로서, $H_2$, CO, $CO_2$ 등의 가스 분자가 표면에 흡착되면 전기저항이 변하는 특성을 가지고 있고, 이러한 성질을 활용하면 다양한 가스의 감지가 가능하기 때문에 가스센서로 연구가 활발히 이루어지고 있다. 나노구조물의 경우 Bulk 상태보다 체적 대비 표면적비가 높기 때문에 기체의 흡착이 유리하고, 가스 센서의 성능이 향상될 수 있다. 본 연구에서는 Thermal CVD 공정을 이용하여 SnO Nanoplatelet을 Si 기판위에 Dense하게 성장시켰다. 기상 수송 방법(Vapor Transport Method)으로 성장된 SnO 나노구조물을 Thermal CVD System을 이용하여 산소분위기에서 $830^{\circ}C$ 및 $1030^{\circ}C$에서 열처리(Post-Annealing)하여 $SnO_2$ 상(Phase)을 갖도록 하였다. 열처리 과정동안 쳄버의 압력을 4.2 Torr로 일정하게 유지시켰다. 열처리 된 SnO 나노구조물의 결정학적 특성을 Raman Spectroscopy 및 XRD 분석을 통하여 확인하였고, 형태학적 변화를 주사전사현미경(Scanning Electron Microscopy)을 통하여 확인하였다. 분석결과 SnO 나노구조물은 열처리 과정을 통하여 $SnO_2$ 나노구조물로 상변환 되었다.