• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2007년도 학술발표회 논문집
• /
• pp.438-443
• /
• 2007

개수로 흐름에 대한 연구는 1700년대 중엽 Chezy에 의해 이론적인 기초를 다졌으며, 광범위하고 조직적인 관측연구는 Darcy(1803-1858)에 의해 약 150년 전에 폭 2m, 길이 600m에 이르는 수로에서 실험관측을 수행하고자 시도하였다. Darcy의 동료이자 후계자인 Bazin은 제한된 조건의 현장관측뿐 아니라 다양한 조건의 수로를 제작하여 실험관측을 수행하였으며 그의 실험자료는 Bazin 자신 뿐만 아니라 Manning이나 Ganguillet와 Kutter 등 여러 연구자들의 경험식 개발에도 이용되었다. Nikuradse(1933)의 균일조도 원형관수로 실험결과로부터 관로 흐름은 층류, 천이층류, 완난류, 천이난류, 전난류 등 다섯 종류의 흐름특성을 가지고 있음을 확인하였고 Bazin(1829-1917)과 varwick(1945)의 실험결과로부터 개수로 흐름에서도 관로 흐름과 마찬가지로 층류, 천이층류, 완난류, 천이난류, 전난류 등 다섯가지의 흐름특성이 존재함을 알 수 있다. 본 연구에서는 기존의 지수형 마찰계수 산정식에서 단순히 조고만의 함수였던 ${\alpha}$에 물의 기본적인 성질인 표면장력, 점성력, 밀도와 자연 하천의 경사, 수심, 수면, 폭, 조고의 영향을 고려한 수심에 관한 무차원수 $Y_h$, 수면 폭에 관한 무차원수 $Y_b$, 조고에 관한 무차원수 $Y_k$를 도입하였다. 따라서 개수로 흐름 해석에 있어서 기존의 마찰계수 산정치보다 여러 영향을 반영하여 정확한 값을 산정할 수 있을 것으로 판단된다.

• 오토저널
• /
• 제6권4호
• /
• pp.36-45
• /
• 1984

The relationship between vehicle driving pattern and fuel consumption in urban area was studied in Seoul along three representative routes using a test car equipped with all the instruments required for recording modes of traffic and measuring fuel consumption. Correlation with idle speed, fuel consumption and CO concentration of car in use was also measured. The average vehicle speed in Seoul was 31.4 km/h and the time spent in different modes was 23.0% in idle mode, 22.5% in acceleration mode, 32.4% in cruising mode and 22.3% in deceleration mode, respectively. Hence, traffic flow was suggested to be relatively smooth. Fuel consumption per unit distance, .phi. was closely related with trip time spent per unit distance, t, and correlation coefficient obtained from the test car was 0.925, and the relationship between .phi. and t was also obtained from the linear regression with the following equation. .phi.=42.87+0.38 t. Idle speed of vehicle in use was mostly adjusted low and cars which were over the permissible standard of CO concentration (4.5%) were 50% or more. As the idle speed decreased, the fuel consumption was decreased, while the CO concentration was increased. Therefore, the decrease of fuel consumption can not be expected with only a decrease in idle speed.

• 한국디지털정책학회:학술대회논문집
• /
• 한국디지털정책학회 2007년도 춘계학술대회
• /
• pp.33-40
• /
• 2007

The Customs Administration, unlike other administrative service, should respond to constantly changing external environment. The Customs has to actively adapt itself to government policy changes, economic changes and international environment changes to facilitate the flow of trade logistics and maintain trading relations wi th other countries. The purpose of this paper is to explain policy directions of the Korea Customs Service which enforces various policies related to tariff and non-tariff barrier elimination for the trade liberalization while the Korean government is pursuing FTAs on a multi-track basis. This paper aims to seek ways to apply FTA policies to the Korean society and economy in a smooth manner. First of all, this paper examines changes in Customs administration brought by the proliferation of FTAs to such areas as FTA negotiations, import/export management, duties and taxes collection, drawback reduction/exempt ion of duty application area of preferential tariff rate and country of origin management. Then, the paper sets FTA missions of "supporting Customs Administration to lead the new trend of free trade environment" after analyzing the environment changes. To achieve the FTA mission mentioned above, the KCS designated 4 strategies and 40 implementation tasks. The 4 strategies are named "4C Strategies" taking initial letters from Client-oriented, Customized procedures, Cooperation and Constitution. "4C" also refers to Foresee(strategies to foresee the successful establishment of FTA policies) or For C(Customer or Customs). The KCS will continue to create new tasks through various channels and monitor their implementation process, and to help FTA regime successfully take root in Korea.

• 한국조리학회지
• /
• 제14권3호
• /
• pp.178-195
• /
• 2008

This examination was conducted as follows; 189 copies were coated in total, and demonstratively analyzed by SPSS WIN 15.0 program. The methods used in data for this analysis are as follows; Sensitivity, Reliability, Frequency, Internal consistency, One way ANOVA(Scheffe's examination) Analysis, T-test, etc. The findings of this study are as follows; firstly, it was revealed that respondents who were regular customers of Italian restaurants regarded convenient transportation, property of space, property of pastoral, visibility, and accessibility as importance. This means that Italian restaurant marketers should consider some of factors of location for business with a good view, good parking lot, location at main street, smooth flow of traffic, luxury, atmosphere of freedom, clean area around restaurants, elegant interior of the building, comfortable, luxurious, and deluxe atmosphere, and so on. Secondly, it was revealed that respondents who were regular customers of buffet restaurant either considered the same factors as the Italian restaurants above or regarded those factors less important. This suggests that restaurants should be located on main streets, on trunk roads, and in large-scale residential districts of apartment complex. Thirdly, it was revealed that respondents who were regular customers of traditional restaurants did not consider the locational factors above. This shows that traditional restaurants should be located in nearby customers' houses or their working places, and that marketers should consider focusing on their restaurants' homelike atmosphere, cleanliness, food flavors, and so on.

• Nuclear Engineering and Technology
• /
• 제33권2호
• /
• pp.241-253
• /
• 2001

Under severe accidents, the pressure and temperature response has an important role for the integrity of a nuclear power plant containment. The history of the pressure and temperature is characterized by the amount and state of steam/air mixture in a containment. Recently, the heat transfer rate to the structure surface is supposed to be increased by the wavy interface formed on condensate film. However, in the calculation by using CONTAIN code, the condensation heat transfer on a containment wall is calculated by assuming the smooth interface and has a tendency to be underestimated for safety. In order to obtain the best- estimate heat transfer calculation, we investigated the condensation heat transfer model in CONTAIN 1.2 code and adopted the new forced convection correlation which is considering wavy interface. By using the film tracking model in CONTAIN 1.2 code, the condensate film is treated to consider the effect of wavy interface. And also, it was carried out to investigate the effect of the different cell modelings - 5-cell and 10-cell modeling - for KNGR(Korean Next Generation Reactor) containment phenomena during a severe accident. The effect of wavy interface on condensate film appears to cause the decrease of peak temperature and pressure response . In order to obtain more adequate results, the proper cell modeling was required to consider the proper flow of steam/air mixture.

• 한국태양에너지학회 논문집
• /
• 제28권1호
• /
• pp.33-42
• /
• 2008

Zr-O ($Zr-ZrO_2$) cermets solar selective coatings with a double cermets layer film structure were prepared using a DC (direct current) magnetron sputtering method. The typical film structure from surface to bottom substrate were an $Al_2O_3$ anti-reflection layer on a double Zr-O cermets layer on an Al metal infrared reflection layer. Optical properties of optimized Zr-O cermets solar selective coating had an absorptance of ${\alpha}\;=\;0.95$ and thermal omittance of ${\epsilon}\;=\;0.10\;(100^{\circ}C)$. The absorbing layer of Zr-O cermets coatings on glass and silicon substrate was identified as being amorphous by using XRD. AFM showed that ZF-O cermets layers were very smooth and their surface roughness were approximately $0.1{\sim}0.2 nm$. The chemical analysis of the cermets coatings were determined by using XPS. Chemical shift of photoelectron binding energy was occurred due to the change of Zr-O cermets coating structure deposited with increase in oxygen flow rate. The result of thermal stability test showed that the Zr-O cermets solar selective coating was stable for use at temperature below $350^{\circ}C$.

• 설비공학논문집
• /
• 제6권2호
• /
• pp.166-174
• /
• 1994

An experimental study has been performed to identify the evaporation characteristics of HCFC-22 for transport refrigeration system. Heat transfer coefficients were measured in a horizontal, smooth evaporating tube with an inner diameter of 10.7mm and a length of 2.8m. The refrigerant was heated electrically by surface-wrapped heaters and uniform power is applied along the tube. The entire tube was divided into 7 sections. Surface temperatures of tube and refrigerant temperature in each test section were measured. Pressure drops in each section and the inlet pressure were also measured. The mass flowrate of the refrigerant was controlled and measured. A single tube evaporation test was conducted for different ranges of mass flux of refrigerant, heat flux of evaporator and condensing temperature of transport refrigeration system. The evaporation heat transfer coefficients of HCFC-22 were compared with predictions from the well known Chen's correlations. Averaged heat transfer coefficients in this experiment range from $2kW/m^2/^{\circ}C$ to $3kW/m^2/^{\circ}C$. Most of the experimental results differ from the predicted ones by less than ${\pm}30%$.

• 동력기계공학회지
• /
• 제11권1호
• /
• pp.63-69
• /
• 2007

The evaporation pressure drop of $CO_2$ (R-744) in a horizontal tube was investigated experimentally. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and an evaporator (test section). The test section consists of a smooth, horizontal stainless steel tube of 4.57 mm inner diameter. The experiments were conducted at saturation temperature of $-5^{\circ}C\;to\;5^{\circ}C$, and heat flux of 10 to $40kW/m^2$. The test results showed that the evaporation pressure drop of $CO_2$ are highly dependent on the vapor quality, heat flux and saturation temperature. The measured pressure drop during the evaporation process of $CO_2$ increases with increased mass flux, and decreased saturation temperature. The evaporation pressure drop of $CO_2$ is much lower than that of R 22. In comparison with test results and existing correlations, the best fit of the present experimental data is obtained with the previous correlation. But existing correlations failed to predict the evaporation pressure drop of $CO_2$. Therefore, it is necessary to develop reliable and accurate predictions determining the evaporation pressure drop of $CO_2$ in a horizontal tube.

• 한국CDE학회논문집
• /
• 제18권6호
• /
• pp.461-469
• /
• 2013

Computer simulation with FEM is very useful to analyze hypervelocity impact phenomena that are tremendously expensive or otherwise too impractical to analyze experimentally. Shock physics can be efficiently handled by mesh adaptation which allows finite element mesh to be locally optimized to resolve moving shock wave in explosion. In this paper, an adaptive meshing technique based upon quadtree data structure was applied to resolve ballistic impact phenomena. The technique can adaptively refine a mesh in the neighborhood of a shock and coarsen the mesh for the smooth flow behind the shock according to a criterion. The criterion for refinement and coarsening is based upon the standard deviation of the gradient of shock pressure on the associated field. Shock simulation starts with the rough mesh of the pressure field and mesh density is increased locally under the criterion at each time step. The results show that the mesh adaptation enables to minimize the global computation error of FEM and to increase storage and computational saving compared to the fixed resolution of the conventional static mesh approach.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권4호
• /
• pp.542-549
• /
• 2008

The evaporation heat transfer coefficient and pressure drop of R-22 and R-407C in a horizontal copper tube were investigated experimentally. The main components of the refrigerant loop are a receiver, a compressor, a mass flow meter, a condenser and a double pipe type evaporator (test section). The test section consists of a smooth copper tube of 6.4 mm inner diameter. The refrigerant mass fluxes were varied from 100 to $300\;kg/m^2s$ and the saturation temperature of evaporator were $5^{\circ}C$. The evaporation heat transfer coefficients of R-22 and R-407C increase with the increase of mass flux and vapor quality. The evaporation heat transfer coefficients of R-22 is about $5.68{\times}46.6%$ higher than that of R-407C. The evaporation pressure drop of R-22 and R-407C increase with the increase of mass flux. The pressure drop of R-22 is similar to that of R-407C. In comparison with test results and existing correlations, correlations failed to predict the evaporation heat transfer coefficient of R-22 and R-407C. therefore, it is necessary to develope reliable and accurate predictions determining the evaporation heat transfer coefficient of R-22 and R-407C in a horizontal tube.