• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.4
• /
• pp.659-665
• /
• 2016

The limit equilibrium method (LEM) is commonly used for slope design and stability analysis because it is easy to simulate slope and requires short calculating time. However, LEM cannot adequately simulate ploughing failure in a footwall slope with a joint set dipping parallel with slope, e.g. bedding joint set. This study performed parametric study to analyze the influence factors on ploughing failure using UDEC which is a commercial two-dimensional DEM (Distinct Element Method)-based numerical program. The influence of joint structure and properties on stability of a footwall slope against ploughing failure was investigated, and the factor of safety was estimated using the shear strength reduction method. It was found that the stability of footwall slope against ploughing failure strongly relies on dip angle of conjugate joint, and the critical bedding joint spacing and the critical length of slab triggering ploughing failure are also affected by dip angle of conjugate joint. The results obtained from this study can be used for effective slope design and construction including reinforcement.

• Journal of the Ergonomics Society of Korea
• /
• v.29 no.4
• /
• pp.681-686
• /
• 2010

Although the height of a ramp is an important design element, it has not been considered in prior studies. Therefore, in this study, the ramp slope and height are considered as independent variables. To analyze the effects of the slope and height, five levels of slope (1:6, 1:8, 1:10, 1:12 and 1:14) and three levels of height (15cm, 30cm and 45cm) are considered. For the dependent variables, the total time, velocity and perceived discomfort were considered as usability measures, pulse rate changes and EMG signals of four related muscles (extensor carpi radialis, triceps brachii, anterior deltoid and posterior deltoid) were considered as physiology measures. As a result, differences among usability and physiological characteristic for the five slopes increased as the height increased. Additionally, slope effects were minor when the height was low (15cm). Almost domestic/international regulations and guidelines related to ramp recommended 1:12 slope for the ramp design, however, there was no significant difference between 1:10 and 1:12 according to result of this study. In addition, slope effects were minor at a low height; thus, a slope of 1:8 can be recommended if the installation space for a gentler ramp is not sufficient.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.10
• /
• pp.29-38
• /
• 2011

The unsaturated layers by rainfall infiltration are not properly reflected in construction codes to do slope design. The objective of this paper is to analyze the slope behavior according to the saturation layer increase resulted from the rainfall infiltration, to do that the laboratory slope model apparatus was adopted. From the model apparatus, the variation of water content and strength parameters of the model slope were analyzed. The safety factors of model slope was decreased, if saturation layer was increased from 3.0m to 4.5m, which means ground water level 3m selected from construction codes makes higher safety level. Also, if the ground water level is located in soil surface, the lower safety level will show up. Therefore, to make the proper slope design, the experiments and analysis of variation of saturation layer is needed.

• Journal of Biosystems Engineering
• /
• v.12 no.3
• /
• pp.62-72
• /
• 1987

The necessity of using land on slopes for agricultural production has been recognized all arable land resources in plains are decreased. Mechanization is one of the main factors determining the extent of cultivating slope lands and it must be considered as a means of increasing labor productivity. This article discussed some relevent aspects of farm mechanization on slopes. It includes the potential slope land resources which can be tilled for food and forage productions, design characteristics of agricultural machines for use in slope lands, and possible solutions of the problems to be encountered in the mechanization process.

• The Journal of Engineering Geology
• /
• v.28 no.4
• /
• pp.605-618
• /
• 2018

Korea follows the slope design criteria during construction. It was enacted by the Ministry of Land, Transport and Maritime Affairs. There are cases where the Soil-nail is designed as a measure to secure slope stability. The arrangement of the soil-nail may be arranged at equal intervals or may be arranged differently depending on the soil failure model. The optimum design of the countermeasure method is determined by securing stability of the slope through optimization of dimensions and shape. However, when uniform nails are placed at low elevations in slopes, the standard safety factor is exceeded, which may hinder economic design. It is preferable to arrange the reinforcement of the nails over the entire slope. When the horizontal spacing of the nails was topology optimized according to the slope height, it was possible to minimize the amount of reinforcement while satisfying the standard safety factor. Since the active load is reduced in the section where the slope height is lowered, the safety factor after reinforcement may be excessively increased. Therefore, the phase optimization method is proposed as an economical optimal design method using the reinforcing shape density. In addition, a relational expression was designed to optimize the horizontal spacing by slope height.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.11b
• /
• pp.103-114
• /
• 2002

Stability of cut-slope is considered to have a deep relationship with rock types since rock has its own engineering and geological characteristic such as shear strength, durability, weathering profile, geological structures. Therefore, analysis of geological and engineering characterisics of rock mass is essential for the evaluation of rock slope stability This paper introduces the statistical data of slope failure cases which was collected from highway slopes constructed in sedimentary rock mainly of shale in Ky ng-sang Basin. Primary failure feature in this area is planar failure along the bedding regardless of slope geometry. Even a disasterous slope failure case due to the thick clay layer between the beddings was reported. Failures and rock fall were reported to ocurred frequently after the completion of cutting due to the weathering, so long-term slope stability should be considered as a important factors in design.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.687-696
• /
• 2006

Slope failure triggered by rainfall produces severe effects on the serviceability and stability of railway. Therefore slope stability problem is one of the major concerns on the operation of railway. In this study we collected rainfall data when and where slope failures were observed. The collected data show that the range of cumulative rainfall is from 150 to 500mm and the rainfall duration is about 3 to 24 hours. By using the collected rainfall information, slope stability analysis considering infiltration was carried. The analyses employs multiple sliding surfaces to find the minimal factor of safety in the infinite slope condition. This approach show more reasonable results than the results from analysis following the design code which assumes that groundwater level and the slope surface are equal.

• 한국터널공학회:학술대회논문집
• /
• 2005.04a
• /
• pp.359-371
• /
• 2005

The Cutting slope is to be minimized when a tunnel meets the contour of slope terrain at a right angle around its portal. However, a tunnel portal has been generally installed at a right angle to the longitudinal axis of a tunnel with no consideration of the intersection angle with the slope terrain. This sometimes tended to cause huge cutting slope that resulted in many disadvantage in terms of safty, economy and environment. Therefore, the minimization of cutting slope is studied by taking the intersection angle into account, and the result is compared with that by the conventional method. In addition a design method for the inclined portal to the tunnel axis is proposed through 3D-FEM analysis, also the applicable ground condition is suggested.

• Journal of the Korean Society of Safety
• /
• v.15 no.2
• /
• pp.103-110
• /
• 2000

This paper deal with the stability evaluation and suggestion of progressive failure slope in biotite granite area of Andong. Based on geological site investigation and field test, stability analysis of slope was performed in conjunction with limit equilibrium methods and stereographic projection. Additionally, initial design and construction procedure was critically evaluated. Series of the slope stability analysis reveals the detection of local wedge and plane failure under the current slope condition. It is additionally appeared that a certain synthetic behavior of circle and plane failure exists on the right spot where the overall failure's going in progress. In order to construct more stable slope based on the suitability for the real state of the slope circumstances, this study issues a solution to eliminate the primary factors which cause the instability, by means of the grade of weathering and RMR classification of rock mass.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.557-560
• /
• 2008

In this paper, it discusses about the stability of rock slope of pyroclastic rock, which can easily meet at construction site. Basically carry out the investigation about the development of a surface of discontinuity, too. With that, it refers to the basic groups of sedimentary rock, treats of general details about investigation of rock slope and stability analysis, and discusses general characteristics and stability analysis case study about rock slope of pyroclastic rock. Achieved basic geological investigation on rock slope of pyroclasic rock, and examine the stability of slope by doing limit equilibrium and geometric stability analysis due to the result of investigation. It is considered to be able to accumulate many data about slope design of pyroclastic rock hereafter estimating degrees of rock mass properties of pyroclastic rock quantitatively.