• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.3
• /
• pp.251-260
• /
• 2003

A three dimensional (3-D) method of analysis is presented for determining the free vibration frequencies and mode shapes of deep, tapered rods and beams with circular cross section. Unlike conventional rod and beam theories, which are mathematically one-dimensional (1-D), the present method is based upon the 3-D dynamic equations of elasticity. Displacement components u/sup r/, u/sub θ/ and u/sub z/, in the radial, circumferential, and axial directions, respectively, are taken to be sinusoidal in time, periodic in , and algebraic polynomials in the r and z directions. Potential (strain) and kinetic energies of the rods and beams are formulated, the Ritz method is used to solve the eigenvalue problem, thus yielding upper bound values of the frequencies by minimizing the frequencies. As the degree of the polynomials is increased, frequencies converge to the exact values. Convergence to four-digit exactitude is demonstrated for the first five frequencies of the rods and beams. Novel numerical results are tabulated for nine different tapered rods and beams with linear, quadratic, and cubic variations of radial thickness in the axial direction using the 3D theory. Comparisons are also made with results for linearly tapered beams from 1-D classical Euler-Bernoulli beam theory.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.3
• /
• pp.259-268
• /
• 2014

In this paper, we suggest a method of extracting circuit parameters of the insulating transformer using S-parameter measurement, especially in high frequency range. At 60 Hz, conventionally, no load test and short circuit test are used to extract the circuit parameters. In this paper S-parameters measured from VNA(Vector Network Analyzer) were used to extract the transformer parameters using data fitting method (optimization). The S-parameters from the equivalent circuit using the extracted parameters showed good agreement with those from measurement. Furthermore, the transformer secondary voltages from the equivalent circuit model also coincide quite exactly to the measured secondary voltages in sinusoidal forms. Finally we assert that the proposed method to extract the parameters for the insulating transformer using S-parameter is valid especially in high frequency.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.47 no.5
• /
• pp.62-73
• /
• 2010

In this paper we proposed a candidate algorithm on G.711.1 and G.722 superwideband extension codec which is under standardization by ITU-T. The proposed codec not only provides an interoperable bitstream with ITU-T G.711.1 and G.722, but also encodes a superwideband signal with a bandwidth of 50-14,000 Hz using superwideband extension layer. The candidate codec consists of a core layer to provide an interoperability with conventional wideband codecs and superwideband extension layer using linear prediction-based sinusoidal coding. The proposed extension codec operates on 5ms frame and provides four superwideband bitrates of 64, 80, 96, and 112 kbit/s depending on the core codec. Since the resulting bitstream has an embedded structure, it can be converted into core bitstream by simple truncation without transcoding. The proposed codec has a short algorithmic delay and low complexity and passed the qualification test of G.711.1 and G.722 superwideband extension codec performed by ITU-T.

• Archives of Plastic Surgery
• /
• v.32 no.3
• /
• pp.369-375
• /
• 2005

Apoptosis is a physiologic or programmed cell death process which is controlled by genes. It is essential for the function and the appropriate development of multicellular organism. It is also thought to be one of the main mechanisms of cell death in ischemic tissues. The effect of prostaglandin $E_1$($PGE_1$) is proven to be useful in the recovery of ischemic changes by inducing vasodilation of peripheral vessels and platelet disaggregation. $PGE_1$ is also known to suppress apoptosis in human liver sinusoidal endothelial cell from ischemia-reperfusion injury. The purpose of this study is to evaluate the effects of $PGE_1$ on the apoptosis in the ischemia reperfusion injury of rat intestine. Thirty Sprague-Dawley rats were used. In control group(N=15), superior mesenteric artery was occluded for 60 minutes and after removing the vessel clamp, it was reperfused for 60 minutes and harvested. In experimental group(N=15), a jejunal flap was also made as in the control group except for the intraarterial administration of the $PGE_1$ right after clamping the artery and removing the clamp. H&E, TUNEL and immunohistochemical stains for p53, bax, and bcl-2 were performed. There were ischemic changes in gross and microscopic findings in both groups. The apoptotic index was significantly lower in the experimental group($1.29{\pm}0.82$(p=0.003)) than in the control group ($2.33{\pm}0.95$). The rat intestinal ischemia apoptosis by ischemia-reperfusion was partly related to the modulating of bcl-2, bax, and p53 expression. Our results indicate that $PGE_1$ suppresses the apoptosis in the ischemic jejunal flap and this effect is probably the result of a increase in expression of bcl-2.

• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.964-973
• /
• 1998

In this paper we propose a levitation and imbalance compensation controller design methodology of magnetic bearing system. In order to achieve levitation and elimination of unbalance vibartion in some operation speed we use the discrete-time Q-parameterization control. When rotor speed p = 0 there are no rotor unbalance, with frequency equals to the rotational speed. So in order to make levitatiom we choose the Q-parameterization controller free parameter Q such that the controller has poles on the unit circle at z = 1. However, when rotor speed p $\neq$ 0 there exist sinusoidal disturbance forces, with frequency equals to the rotational speed. So in order to achieve asymptotic rejection of these disturbance forces, the Q-parameterization controller free parameter Q is chosen such that the controller has poles on the unit circle at z = $exp^{ipTs}$ for a certain speed of rotation p ( $T_s$ is the sampling period). First, we introduce the experimental setup employed in this research. Second, we give a mathematical model for the magnetic bearing in difference equation form. Third, we explain the proposed discrete-time Q-parameterization controller design methodology. The controller free parameter Q is assumed to be a proper stable transfer function. Fourth, we show that the controller free parameter which satisfies the design objectives can be obtained by simply solving a set of linear equations rather than solving a complicated optimization problem. Finally, several simulation and experimental results are obtained to evaluate the proposed controller. The results obtained show the effectiveness of the proposed controller in eliminating the unbalance vibrations at the design speed of rotation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.4
• /
• pp.65-73
• /
• 2003

This paper presents the implementation of an analog signal-processing ASIS to detect an angular velocity signal from a vibrator angular velocity detection sensor. The output of the sensor to be charge appeared as the variation of the capacitance value in the structure of the sensor was detected using charge amplifiers and a self oscillation circuit for driving the sensor was implemented with a sinusoidal self oscillation circuit using the resonance characteristics of the sensor. Specially an automatic gain control circuit was utilized to prevent the deterioration of self-oscillation characteristics due to the external elements such as the characteristic variation of the sensor process and the temperature variation. The angular velocity signal, amplitude-mod)Hated in the operation characteristics of the sensor, was demodulated using a synchronous detection circuit. A switching multiplication circuit was used in the synchronous detection circuit to prevent the magnitude variation of detected signal caused by the amplitude variation of the carrier signal. The ASIC was designed and implemented using 0.5${\mu}{\textrm}{m}$ CMOS process. The chip size was 1.2mm x 1mm. In the experiment under the supply voltage of 3V, the ASIC consumed the supply current of 3.6mA and noise spectrum density from dc to 50Hz was in the range of -95 dBrms/√Hz and -100 dBrms/√Hz when the ASIC, coupled with the sensor, was in normal operation.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.5
• /
• pp.62-70
• /
• 2007

In this paper, the boost Power Factor Correction(PFC) technique for Direct Torque Control(DTC) of brushless DC motor drive in the constant torque region is implemented on a TMS320F2812DSP. Unlike conventional six-step PWM current control, by properly selecting the inverter voltage space vectors of the two-phase conduction mode from a simple look-up table at a predefined sampling time, the desired quasi-square wave current is obtained, therefore a much faster torque response is achieved compared to conventional current control. Furthermore, to eliminate the low-frequency torque oscillations caused by the non-ideal trapezoidal shape of the actual back-EMF waveform of the BLDC motor, a pre-stored back-EMF versus position look-up table is designed. The duty cycle of the boost converter is determined by a control algorithm based on the input voltage, output voltage which is the dc-link of the BLDC motor drive, and inductor current using average current control method with input voltage feed-forward compensation during each sampling period of the drive system. With the emergence of high-speed digital signal processors(DSPs), both PFC and simple DTC algorithms can be executed during a single sampling period of the BLDC motor drive. In the proposed method, since no PWM algorithm is required for DTC or BLDC motor drive, only one PWM output for the boost converter with 80 kHz switching frequency is used in a TMS320F2812 DSP. The validity and effectiveness of the proposed DTC of BLDC motor drive scheme with PFC are verified through the experimental results. The test results verify that the proposed PFC for DTC of BLDC motor drive improves power factor considerably from 0.77 to as close as 0.9997 with and without load conditions.

• Korean Journal of Optics and Photonics
• /
• v.17 no.1
• /
• pp.47-53
• /
• 2006

The Integrated Ballistics Identification Systems (IBIS) is widely used for bullet and casing signature identification. The IBIS obtains a pair of ballistic signatures from two bullets (or casings) using optical microscopy, and estimates a correlation score which can represent the degree of signature match. However, this method largely depends on lighting and surface conditions because optical image contrast is primarily a function of test surface's slope, shadowing, multiple reflections, optical properties, and illumination direction. Moreover, it can be affected with surface height variation. To overcome these problems and improve the identification system, we used well known surface topographic techniques, such as confocal microscopy and white-light scanning interferometry. The measuring instruments were calibrated by a NIST step height standard and verified by a NIST sinusoidal profile roughness standard and a commercial roughness standard. We also suggest a new analysis method for the ballistic identification. In this method, the maximum cross-correlation function CCFmax is used to quantify the degree of signature match. If the compared signatures were exactly the same, CCFmax would be $100\%$.

• Journal of Nutrition and Health
• /
• v.1 no.3_4
• /
• pp.201-205
• /
• 1968

The authors has observed the histopathologically and histochemically on the effect of the garlic and garlic oil to the liver and kidney of rats. In order to confirm the histochemical changes of the metabolism of polysaccarides, the periodic acid Schiff reaction was applied. The 30 albino adult male rats weighing about 150 grames from the National Institute of Health were housed individualy and devide into 3 experimental groups: Group C: stock diet group Group B: stock diet-garlic group Group A: stock diet-garlic oil group Group C was fed with stock diet only through out this experimental period, Group B was fed with stock diet supplemented with garlic homogenator to be 1%, and Group A was fed with stock diet supplemented with the garlic oil to 0.05%. The garlic oil used in this experiments was extracted by author. And all rats was fed during 10 weeks. The histopathological and histochemical results were shown in each figure. According to the all results, the following concIusions were drawn. 1) In the garlic oil administrated groups, congestion of the sinusoid was subsided and the liberation of the Kupffer's cells were observed. 2) In garlic administrated groups, fatty metamorphosis in hepatic cells, and slight liberation of Kupffer's cells in sinusoidal walls were observed. Connective tissue proliferation and collagen bundle were observed. 3) The connective tissue and blood vessel wall in portal area Were reacted intensely with PAS stain. The hepatic cells Were reacted intensely with PAS stain in control group and moderately or slightly in garlic and garlic oil administrated group. 4) There were no significant differences in collecting and Henle's loops in each groups, but narrowing of lumen of the distal tubules were observed in garlic oil administrated group. 5) The basement membrane of the tubules and the connective tissues of the vessel wall in Kideny were reacted intensely with PAS stain in each groups. In control and garlic administrated groups. the brush border of the proximal tubules were reacted intensely with PAS stain, but epithelium of the Heine's loop, proximal, distal and collecting tubules were reacted moderately. In garlic oil administrated-group, there were tendency of decreasing of PAS stain in each tubules.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.4
• /
• pp.659-666
• /
• 2006

Servo-motors are used as key components of automated system by performing precise motion control as accurate positioning and accurate speed regulation in response to the commands from computers and sensors. Especially, the linear brushless servo-motors have numerous advantages over the rotary servo motors which have connection with the friction induced transfer mechanism such as ball screws, timing belts, rack/pinion. This paper proposes an estimation method of unknown motor system parameters using the informations from the sinusoidal driving type linear brushless DC motor dynamics and outputs. The estimated parameters can be used to tune the controller gain and a disturbance observer. In order to meet this purpose high performance Digital Signal Processor, TMS320F240, designed originally for implementation of a Field Oriented Control(FOC) technology is adopted as a controller of the liner BLDC servo motor. Having A/D converters, PWM generators, rich I/O port internally, this servo motor application specific DSP play an important role in servo motor controller. This linear BLDC servo motor system also contains IPM(Intelligent Power Module) driver and hail sensor type current sensor module, photocoupler module for isolation of gate signals and fault signals.