• Journal of Powder Materials
• /
• v.8 no.2
• /
• pp.110-116
• /
• 2001

Abstract To investigate the effect of mechanical alloying process to thermoelectric properties of PbTe sintered body, Pb-Te mixed powder with Pb : Te : 1 : 1 composition was mechanically alloyed using tumbler-ball mill. Thermoelectric properties of the sintered body were evaluated by measuring of the Seebeck coefficient and specific electric resistivity from the room temperature to 50$0^{\circ}C$. Sintered body of only mechanically alloyed PbTe powder showed p-type behavior at the room temperature, and occurred type transition from p-type to n-type at about 30$0^{\circ}C$. PbTe sintered body which was fabricated using heat treated powder in $H_2$ atmosphere after mechanical alloying showed stable n-type behavior under 50$0^{\circ}C$. N-type PbTe sintered body fabricated by mechanical alloying process had 4 times higher power factor than that fabricated by the melt-crushing process. Application of a mechanical alloying process to fabricate of n-type PbTe thermoelectric material seemed to be useful to increase the power factor of PbTe sintered body.

• Metals and materials international
• /
• v.24 no.6
• /
• pp.1422-1431
• /
• 2018

We investigated the additional (secondary) cooling effect of casted strips on the magnetic properties of Nd-Fe-B sintered magnets. The Nd-Fe-B sintered magnets were fabricated with the casted strips prepared without and with additional cooling. Additional cooling was achieved by blowing Ar gas at various pressures (0.1, 0.3, and 0.6 MPa) on the free-side surface of the strips during the strip-casting process. The higher magnetic properties of $H_c$, $B_r$, and $(BH)_{max}$ of the final Nd-Fe-B sintered magnets were obtained for 0.1 MPa rather than for 0.0 MPa. The best microstructure of the columnar grains in the casted strips was produced with the aid of a lower pressure of gas on the free-side surface. It was found that the microstructure of the strips affects the distribution of grains grown in the sintered magnets. This report demonstrates that the improved magnetic performance of Nd-Fe-B sintered magnets was achieved via additional gas cooling.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.4
• /
• pp.215-222
• /
• 2023

3Y-TZP (3 mol% yttria-stabilized tetragonal zirconia polycrystals, 3Y-TZP) ceramics are emerging as dental implant materials due to their superior optical and mechanical properties as well as excellent biophysical properties, in spite of low bioactivity. In this study, we investigated to sintered properties and microstructural defects of dental zirconia implants fabricated by ceramic injection molding and post-HIP (Hot isostatic pressing) processing and analyzed the processing parameters related with the obtainment of its high sinterd density. Sintered and microstructural parameters, i.e, apparent density, grain size and phase composition of zirconia implants fabricated by injection molding were dependent on the fixtute size and implant type. Maximum sintered density of 99.2% and minimum grain size of 0.3-0.4 ㎛ were obtained from large-scaled 2-body sample. In 1-body ceramic implant, high sintered density of 99.5% was obtained, but it had a little monoclinic phase and wide grain size distribution.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.987-988
• /
• 2006

The processes of P/M affect the properties of sintered gears. The different techniques of P/M lead to the different properties of sintered gears. This paper summarizes new progress in powder metallurgy for sintered gears. These progresses include warm compaction, high velocity compaction, sinter hardening, high temperature sintering, infiltration, CNC powder press and surface densification etc.

• Resources Recycling
• /
• v.9 no.2
• /
• pp.18-25
• /
• 2000

Magnetic and physical properties of sintered bodies prepare from waste sintered barium hexaferrite magnets which were come from fabrication process of isotropic permanent magnets were investigated. The properties of the sintered bodies were characterized by XRD, XRF, SEM, and BH curve tracer. After the waste permanent magnets were milled and granulated, the granules of the waste permanent magnet powders and the commercial granules were mixed with various proportions, pressed, and sintered. although the magnetic properties were decreased gradually with the content of waste magnet powder, the magnetic characteristics of the sintered magnets at $1150~1200^{\circ}C$ were comparable to those required for isotropic permanent magnets.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.11a
• /
• pp.273-274
• /
• 2023

In this study, ultrasonic pulse velocity was analyzed to evaluate the high-temperature mechanical properties of concrete mixed with non-sintered hwangto. The W/B of the specimens was set at 0.41, the percentage of non-sintered hwangto admixture was set at two levels of 15,30%. The target temperature of the specimen is set to 6 levels of 20, 100, 200, 300, 500, 700 ℃, and the heating rate is set to 1℃/min. The result showed that the amount of non-sintered hwangto incorporated into the concrete tends to results in lower compressive strength. Ultrasonic pulse velocity showed similar trends, but differed in some areas.

• Journal of Powder Materials
• /
• v.23 no.6
• /
• pp.447-452
• /
• 2016

Neodymium-iron-boron (Nd-Fe-B) sintered magnets have excellent magnetic properties such as the remanence, coercive force, and the maximum energy product compared to other hard magnetic materials. The coercive force of Nd-Fe-B sintered magnets is improved by the addition of heavy rare earth elements such as dysprosium and terbium instead of neodymium. Then, the magnetocrystalline anisotropy of Nd-Fe-B sintered magnets increases. However, additional elements have increased the production cost of Nd-Fe-B sintered magnets. Hence, a study on the control of the microstructure of Nd-Fe-B magnets is being conducted. As the coercive force of magnets improves, the grain size of the $Nd_2Fe_{14}B$ grain is close to 300 nm because they are nucleation-type magnets. In this study, fine particles of Nd-Fe-B are prepared with various grinding energies in the pulverization process used for preparing sintered magnets, and the microstructure and magnetic properties of the magnets are investigated.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.818-819
• /
• 2006

The effect of individual gas constituents in a sintering atmosphere is examined to optimize the sintered properties of Iron-Carbon P/M components. The influence of sintered properties is reviewed as a function of hydrogen percentages and dew point in the sintering zone. Microstructures, porosity, pore morphology and dimensional changes are the subject of this review. The effects of CO containing atmospheres are compared against the non CO atmospheres in terms of hardness, carbon control and dimensional changes.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.690-691
• /
• 2006

Variable valve timing unit, which is able to decrease environmental load and improve fuel economy is loaded onto many automobiles recently. This unit consists mainly of sprocket, housing and rotor. These parts are requested different properties according to environment. We produce sintered parts for variable valve timing unit by selecting compact, sinter process and special treatment according to demanded properties. In this paper, demanded properties of sintered parts for variable valve timing unit and adopted technique to satisfy them are presented.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1991.10a
• /
• pp.17-19
• /
• 1991

Pastes consisting of $CdZnS_{1-y}Te_{y}$ powder, 20wt/o of $CdCl_2$as a sintering aid and appropriate amount of Propylene Glycol(P.G) have been coated on glass substrates and were sintered at the temperature of $625^{\circ}C$ to find energy band gap, transmittance and electrical properties of the sintered films. The resistivity of sintered film increases with increasing Te content. X-ray diffraction patterns show that $CdZnS_{0.9}Te_{0.1}$ sintered film is in the single film in the two phase region. The transmittance of the sintered film decreases with increasing the Te content.