• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.552-554
• /
• 2004

Barrier ribs of plasma display panel (PDP) are glass matrix composite reinforced with alumina particles. Mechanical properties of the ribs are very crucial for the improvement in reliability of the panel as the ribs might fracture during transportation and service. In this study, therefore, the effects of filler type and content on the mechanical properties of the ribs were investigated. The fillers used include $Al_2O_3$, $TiO_2$, $ZrO_2$ and fused silica. The content of the filler was changed from 0 to 40 vol.%. The mechanical properties of the ribs measured were hardness, Young's modulus, fracture toughness, and 3-point bending modulus. The fracture toughness evaluated by micro-Vicker's indentation of the composites, in general, was measured to increase with the content of the filler until the sintered density does not decrease significantly. The improvement, however, was dependent on the type of filler employed.

• Journal of the Korean Ceramic Society
• /
• v.31 no.8
• /
• pp.879-885
• /
• 1994

Coprecipitation technique was used to synthesize ZrO2+12 mol% CeO2 powders with ZrOCl2.8H2O and Ce(NO3)3.6H2O as starting materials. The powders were dried on different conditions such as distilled water, ethanol, and azeotropic distillation. The powders prepared by azeotropic distillation showed weak aggregation of particles and the average particle size of powders calcined at 85$0^{\circ}C$ for 1 hour was 0.19 ${\mu}{\textrm}{m}$. The optimum sintering temperature and holding time are 130$0^{\circ}C$ and 2.5~10 hours, respectively. Beyond the optimum conditions, a phase transition from tetragonal to monoclinic causes to produce cracks in the sintered bodies and to decrease the density.

• Journal of the Korean Ceramic Society
• /
• v.19 no.4
• /
• pp.300-308
• /
• 1982

A new perovskite type compound, (Pb1a-χKy□χ-y) (Zr0.33Ti0.67)O3-χ+y/2 was proposed and synthesized by "Wet-Dry Combination Technique". This defect ferroelectric material was characterized by partial substitutions of K+ for Pb+2 in Pb(Zr0.33Ti0.67)O3. This material was mono-phasic perovskite compound at 800℃ for 1hr., but ZrO2 was more or less isolated from the (Pb1a-χKy□χ-y) (Zr0.33Ti0.67)O3-χ+y/2. As a result, snitering temperature, sintered density, curie temperature, and dielectric constant of test pieces decreased and a-axis was nearly constant, while c-axis gradually decreased with the value x in the region of tetragonal phase of PZT. It was also recognized that the defect structure caused by adding K+ was found in both A-site cation and O-site anion vacancies in the defect PZT.

• Journal of the Korean Ceramic Society
• /
• v.32 no.2
• /
• pp.257-269
• /
• 1995

The TiC-Co/Al reaction-sintered products were prepared by the infiltration of various Co/Al metal mixture into the preform, and their microstructure, phases, and mechanical properties were investigated. With increasing the atomic ratio of Co/Al, tiC grain shape was changed from spherical to platelet particles, and the grain size increased. The crystalline phases found in the liquid matrix formed by the infiltration of Co/Al metal mixture were determined to be Al5Co2 and AlCo by EDS and XRD, and the two crystalline phases were located dominantly between TiC grains, when the Co/Al atomic ratio was lower than an unity. There was a tendency that the density, bending strength and fracture toughness increase with Co/Al atomic ratio until the infiltrated metal was 100% Co. The maximum value was achieved by the composition containing 100% Co infiltrated metal. The Vickers hardness decreased as Co/Al atomic ratio increased.

• Journal of the Korean Ceramic Society
• /
• v.32 no.4
• /
• pp.436-440
• /
• 1995

Effects of microstructure of two Mg-ferrite specimens with the same starting composition and relative density but with different grain size on B-H hysteresis loop, natural resonance frequency, and ferromagnetic resonance line width are reported. Such properties as B-H hysteresis loop, saturation magnetization, natural resonance frequency, and ferromagnetic resonance line width were influenced by the microstructure development during sintering. Large grain size specimen showed high saturation magnetization, low coercive force, low natural resonance frequency, and low ferromagnetic resonance line width compared with the specimen of small grain size. The main reason for the changes in properties can be explained by the variation in anisotropic characteristics due to Fe+2 content generated during sintering process.

• Journal of the Korean Ceramic Society
• /
• v.27 no.1
• /
• pp.118-126
• /
• 1990

Titanium Cabride powders were prepared by the self-propagating high temperature synthesismethod in air from the mixture of metal titanium powder and carbon powder. The result are as follows : 1. The conversion effciency of higher than 95% can be obtained and the lattice constant value of the product was 4.322$\AA$. 2. The combustion mode, velocity and temperature of combustion wave was photographed using high-speed camera, and showed steady-state, velocity of 15.414mm/sec at 250$0^{\circ}C$. 3. The relative density and MOR strength of TiC sintered at 180$0^{\circ}C$ for 90 minutes by hot-pressing under the pressure of 200kg/$\textrm{cm}^2$ were 95% and 395MPa, respectively.

• Journal of the Korean Ceramic Society
• /
• v.16 no.4
• /
• pp.225-236
• /
• 1979

The effect of $Ti^{+4}$ addition on the sinterability, microstructure, and temperature dependence of electromechanical coupling factor of magnetostrictive Ni-Cu-Co ferrite was investigated. The density of Ni-Cu-Co ferrite slightly increased by 2.0 mole % addition of either $TiO_2$ or $Fe_2TiO_4$, but tended to decrease by more than 2.0 mole % addition of $TiO_2$ or $Fe_2TiO_4$. As the content of either $TiO_2$ or $Fe_2TiO_4$ increased, the magnetocrystalline anisotropy compensation temperature also increased. Microstructure studies showed the stable grains when Ni-Cu-Co ferrite was sintered above 1, 20$0^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.16 no.1
• /
• pp.13-20
• /
• 1979

High purity alumina has been extracted form low grade Korean alunite. Alunite ore was treated by 15% $NH_4OH$ solution, followed by 10% $H_2SO_4$ leaching and metallic impurities such as Fe and Ti were removed by solvent extraction method. Alumina prepared by the extraction process was 99.9% in purity. Hot Petroleum Drying Method has been employed for the preparation of uniformly fine alumina powder, using chemical reagent aluminum sulfate and ammonium aluminum sulfate extrated from Korea alunite. The sinterability of alumina powder prepared by Hot Petroleum Drying Method was shown to be improved in comparison with the one treated by other methods such as ball milling method, but dry pressing was difficult due to the agglomeration of calcined powder. The best slip of alumina powder prepared by Hot Petroleum Drying Method contained a lower soild content than the one treated by other methods. The alumina body formed by soild and drain casting with the former alumina powder showed a higher sintered density.

• Journal of the Korean Ceramic Society
• /
• v.24 no.5
• /
• pp.431-436
• /
• 1987

High purity Al2O3 has been extracted from serlcite of clayminerals, selicite was treated by H2SO4(2N∼18N) solution, NH4OH treatment(PH8.5∼10.0) and metallic impurities such as Fe were removed by NaOH treatment. The tendency of extraction yield of ${\alpha}$-Al2O3 have been investigated by relating reaction time, acid concentration. Reaction products were analyzed by DT-TGA, chemical analysis and X-ray diffractometer. Prepared ${\alpha}$-Al2O3 power is fired in air at 1400$^{\circ}C$, 1600$^{\circ}C$ 2hr. The results are as follows; 1. The most suitable extracting conditions of ${\alpha}$-Al2O3 from Selicite were N-H2SO4, 120 min acidtreating time. 2. The optimum pH condition was 9.0. 3. Physical properties of sintered Al2O3 bodies were as follows. Relative density is 99%. Water absorption is 0.26%. Rock well hardness is 89.

• Journal of Mechanical Science and Technology
• /
• v.14 no.8
• /
• pp.823-829
• /
• 2000

[ $Nb/MoSi_2$ ]laminate composites have been successfully fabricated by hot pressing in a graphite mould. Lamination of Nb foil and $MoSi_2$ layer showed a sufficient improvement in the absorbed impact energy compared to that of monolithic $MoSi_2$ material. The impact value of $Nb/MoSi_2$ laminate composites obviously is reduced when sintered at temperatures higher than 1523K, even if the composite density contributing to impact load increased along with fabricating temperatures. Impact value of laminate composites was also drastically decreased with the growth of reaction layer after the heat treatment. However, it was effective to increase the pressure at the same sintering temperature for the improvement of the impact value.