• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.3
• /
• pp.152-162
• /
• 2003

In this paper, Binary to Quaternary Converter(BQC), Quaternary to Binary Converter(QBC) and Quaternary inverter circuit, which is the basic logic gate, have been proposed based on voltage mode. The BQC converts the two bit input binary signals to one digit quaternary output signal. The QBC converts the one digit quaternary input signal to two bit binary output signals. And two circuits consist of Down-literal circuit(DLC) and combinational logic block(CLC). In the implementation of quaternary inverter circuit, DLC is used for reference voltage generation and control signal, only switch part is implemented with conventional MOS transistors. The proposed circuits are simulated in 0.35 ${\mu}{\textrm}{m}$ N-well doubly-poly four-metal CMOS technology with a single +3V supply voltage. Simulation results of these circuit show 250MHz sampling rate, 0.6mW power consumption and maintain output voltage level in 0.1V.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.6
• /
• pp.553-559
• /
• 2015

The purpose of this research is to develop a gait assistive device to enhance the gait stability and training efficiency of stroke patients. The configuration of this device is mainly composed of a motored wheel and a single cane whose lower end is attached to a motored wheel frame. A patient can feel haptic information from continuous ground contact from the wheel while walking through the grip handle. In addition, the wheeled cane can avoid using excessive use of the patient's upper limb for weight support and motivate the patient to use a paralyzed lower limb more actively. Moreover, the proposed device can provide intuitive and safe user interaction by integrating a force sensor and a tilt sensor equipped to the cane frame, and a switch sensor at the cane's handle. The admittance control has been implemented for the patient to change the walking speed intuitively by using the interaction forces at the handle. A hemi-paretic stroke patient participated in the walking assistive experiments as a pilot study to verify the effectiveness of the proposed haptic cane system. The results showed that the patient could improve walking speed and muscle activations during walking with a constant speed mode of the haptic cane. Moreover, the patient could maintain the preferred walking speeds and gait stability regardless of the magnitude of resistance forces with the admittance control mode of the haptic cane. The proposed robotic gait assistive device with a simple and intuitive mechanism can provide efficient gait training modes to stroke patients with high possibilities of widespread utilizations.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.8
• /
• pp.10-21
• /
• 1999

This paper describes a 12bit CMOS current cell matrix D/A converter which shows a conversion rate of 65MHz and a power supply of 3.3V. Designed D/A converter utilizes current cell matrix structure with good monotonicity characteristic and fast settling time, and it is implemented by using the tree structure bias circuit, the symmetrical routing method with ground line and the cascode current switch to reduce the errors of the conventional D/A converter caused by a threshold voltage mismatch of current cells and a voltage drop of the ground line. The designed D/A converter was implemented with a $0.6{\mu}m$ CMOS n-well technology. The measured data shows a settling time of 20ns, a conversion rate of 50 MHz and a power dissipation of 35.6mW with a single power supply of 3.3V. The experimental SNR, DNL, and INL of the D/A converter is measured to be 55dB, ${\pm}0.5LSB$, and ${\pm}2LSB$, respectively.

• Safety and Health at Work
• /
• v.7 no.4
• /
• pp.347-353
• /
• 2016

Background: This study aimed to investigate the relation between key strike forces and musculoskeletal symptoms (MSS). Moreover, this study presents a key strike force measurement method to be used in a workplace setting. The correlation between key strike force characteristics and MSS was previously studied, but the measurement methods used either a single-key switch or force platforms applied under the keyboard. Most of the studies were conducted in a laboratory setting. The uniqueness of measurement methods in the current study is their ability to measure forces applied to a specific key in a workplace setting and to provide more information about specific key strike forces during typing. Methods: Twenty-four healthy computer workers were recruited for the study. The demographic questionnaire, and self-reported questionnaires for psychosocial status (General Nordic Questionnaire for Psychological and Social Factors at Work) and for detecting MSS were filled up, which later helped in dividing the participants into two groups (12 participants with pain and 12 without pain). Participants typed a predetermined text that utilized the instrumented keys multiple times. The dynamic forces applied to the keys were recorded and collected, using four thin and flexible force sensors attached to the preselected keys according to their location. Results: The results demonstrated that participants with high levels of MSS, specifically in the back and neck, in the last year exerted significantly higher key strike forces than those with lower levels of symptoms (p < 0.005). Conclusion: The key strike force exerted while typing on a keyboard may be a risk factor for MSS, and should therefore be considered in ergonomic evaluations and interventional programs.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.9
• /
• pp.1633-1640
• /
• 2016

In this paper, we propose a open-ended rectangular microstirp patch antenna with fork-shaped feeding structure. This antenna extends the effective bandwidth by transforming single or multi resonant frequency and is designed planar monopole structure with microstrip line to satisfy the WLAN bands (2.4 - 2.484, 5.15 - 5.35, 5.25-5.825 GHz). The substrate is printed in 0.8 mm thickness on an FR-4 board. A commercial 3D simulation tool was used to analyze surface current and electromagnetic field distribution in order to analyze the operation mode and reconfiguration principle of antenna. According to the lengths of individual patches, simulated reflection loss was compared to obtain optimized values. When it was designed with the optimized values, it satisfied WLAN bands (2.380 - 2.710, 4.900 - 5.950 GHz), if the switch is off, and 2.4 WLAN band (2.380 - 2.710 GHz). From the fabricated and measured results, measured results of return loss, gain and radiation patterns characteristics displayed for operating bands.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.6
• /
• pp.727-735
• /
• 2005

Statement of problem. Platform switching in implant prosthesis has been used for esthetic and biological purpose. But there are few reports for this concept. Purpose. The purpose of this study is evaluation of platform switching in wide implant by three dimensional finite element analysis. Materials and Methods. The single implant and prosthesis was modeled in accordance with the geometric designs for Osstem implant system. Three-dimensional finite element models were developed for (1) a wide diameter 3i type titanium implant 5 mm in diameter, 13 mm in length with wide cemented abutment, titanium alloy abutment screw, and prosthesis (2) a wide diameter 3i type titanium implant 5 mm in diameter, 13 mm in length with regular cemented abutment, titanium alloy abutment screw and prosthesis(platform switching) was made for finite element analysis. The abutment screws were subjected to a tightening torque of 30 Ncm. The amount of preload was hypothesized to 650N, and round and flat type prostheses were loaded to 200 N. Four loading offset point (0, 2, 4, 6 mm from the center of the implants) were evaluated. Models were processed by the software programs HyperMesh and ANSA. The PAM-CRASH 2G simulation software was used for analysis of stress. The PAM-VIEW and HyperView were used for post processing. Results. The results from experiment were as follows; 1. von Mises stress value is increased in order of bone, abutment, implant and abutment screw. 2. von Mises stress of abutment screw is lower when platform switching. 3. von Mises stress of implant is lower when platform switching until loading offset 4 mm. 4. von Mises stress of abutment is similar between each other. 5. von Mises stress of bone is slightly higher when platform switching. Conclusion. The von Mises stress pattern of implant components is favor when platform switch ing but slightly higher in bone stress distribution than use of wide abutment. The research about stress distribution is essential for investigation of the cortical bone loss.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.1
• /
• pp.70-77
• /
• 1999

An extremely cadmium-tolerant budding yeast, Hansenula anomala B-7 underwent a morphological switch in response to either heat shock treatment or cadmium stress, respectively. It exhibited a morphological transition from a unicellular yeast form to a pseudohyphae-like coagulation when subjected to prolonged heat shock treatment. In contrast, the yeast cells showed an irregularity in surface morphology when given thermal stress for a short time. Patterns of proteins expressed in the pseudohyphae-like cells demonstrated that several proteins were overexpressed while others were underexpressed in comparison with those prepared from the cells in the yeast form. It was a striking feature, however, that nearly 40％ of the proteins extracted from the cells in the pseudohyphae form appeared to be composed of a single polypeptide. This polypeptide was apparently overexpressed during the pseudohyphae phase and its molecular weight was estimated to be 58 kDa according to SDS-PAGE analysis. However, a significant level of the protein was not observed in the cells before transition to pseudohyphae. The architecture of the cell shape was also damaged when incubated in a medium containing more than 1,000 ppm (8.9mM) of cadmium ions, although able to proliferate at a slow rate. However, the irregularity in the cell morphology exerted either by the brief heat shock treatment or by the cadmium stress with the high concentrations of the metal ions was not repaired, even though the damaged cells were allowed to grow for sufficient time in fresh, cadmium-free medium.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.1
• /
• pp.7-15
• /
• 2002

This paper is concerned with remote environment monitoring & control for the breeding house as scattering far and wide. The environment data is detected in the breeding house that is collected to one processor. It's adapted to the PSTN(public switch tele-phone network) and multi-processing for exchange the environment data and the control data in between the manager and a breeding house by micro-processor. We have designed the algorithm of the communication sequence through the experimental research. This system is composed of sensor interface, FSK communications, LED display, data latch and MCS-51 single-chip. The S/W is composed with data acquisition by multi-processing, data communication and interrupt. And this paper is Proposed the DB structure algorithm concern to a mount scale using web design. The subject is a performance of effective management for the breeding house.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.6
• /
• pp.699-706
• /
• 2015

A previous adapter have a single-ouput, however, a demand of a multi-output adapter increase in the recent industrial site. In order to satisfy the demand, in this research, we implement a programmable high efficiency multi-output adapter. The basic structure of the adapter introduced in this paper is a sort of flyback. The way for producing the reference voltage of the adapter proposed is similar to the way in the general flyback implemented with TL431. In addition to the basic concept of the design, however, we introduce a digital variable resistor, AD5246BKSZ10-RL7 and a microcontroller for changing a programmable multi-output. It makes output be variable that the digital variable resistor change the reference voltage of the adapter by order of the microcontroller. The adapter output voltage is controllable in the range of 20V by the user, and the power efficiency is proven to be 85%.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.6
• /
• pp.486-494
• /
• 2012

In this paper, we proposes the three-phase embedded Z-source inverter consisting of the three embedded Z-source converters and it's the output voltage control method. Each embedded Z-source converter can produce the bipolar output capacitor voltages according to duty ratio D such as single-phase PWM inverter. The output AC voltage of the proposed system is obtained as the difference in the output capacitor voltages of each converter, and the L-C output filter is not required. Because the output AC voltage can be stepped up and down, the boost DC converter in the conventional two-stage inverter is unnecessary. To confirm the validity of the proposed system, PSIM simulation and a DSP based experiment were performed under the condition of the input DC voltage 38V, load $100{\Omega}$, and switching frequency 30kHz. Each converter is connected by Y-connection for three-phase loads. In case that the output phase voltage is the same $38V_{peak}$ as the input DC voltage and is the 1.5 times($57V_{peak}$), the simulation and experimental results ; capacitor voltages, output phase voltages, output line voltages, inductor currents, and switch voltages were verified and discussed.