• 한국공간정보시스템학회:학술대회논문집
• /
• 2004.05a
• /
• pp.83-88
• /
• 2004

First author proposed a proportioning method for member sections of a single layer reticulated dome subjected to uniform and non-uniform load without any geometrical initial imperfection, and discussed the validity and effectiveness of the method which was based on linear buckling stress and a knock down factor. However, buckling of a single layer reticulated dome is strongly affected by initial imperfection. It is well known that geometrical initial imperfections reduce the nonlinear buckling capacity of a single layer raticulated dome. Thus, structural engineers may be recommended to reflect the effects of geometrical initial imperfections in proportioning member sections. In this paper, firstly, the presented proportioning method by first author is applied to dome without consideration of any imperfections and the thickness and diameter of each member are determined. Secondly, the load bearing capacities of the proportioned domes are checked with the imperfection, by the inelastic buckling analysis.

• Proceeding of KASS Symposium
• /
• 2005.05a
• /
• pp.147-153
• /
• 2005

The single layer latticed dome is very sensitive on the slenderness ratio and half open angle of the elements, load condition, and the connection type because it is originazed by a lot of thin elements, so we have to use the geometrically nonlinear buckling load when the buckling of the structures is analyzed. But, it is very difficult to design the single layer latticed domes considered all conditions. Therefore the purpose of this paper is to propose the appropriate design method of the single layer latticed dome considered the geometrically nonlinear buckling load in base of the linear buckling load by the eigenvalue analysis.

• Journal of Korean Association for Spatial Structures
• /
• v.13 no.4
• /
• pp.75-81
• /
• 2013

The circular hollow section is usually used for member of main frame to carry the external load in single layer lattice dome. But, the H-shaped section may be used for member of main frame since it is convenient for attaching roof panels. Single layer lattice domes have various buckling characteristics, such as the overall buckling, the member buckling, and nodal buckling. The purpose of this study is to compare buckling characteristics of single-layer lattice domes in which the H-shaped steel section as the existing domestically-produced structural steel is used as main frames to those of domes in which a circular hollow section is used as main frames.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1997.04a
• /
• pp.240-247
• /
• 1997

Single-layer latticed domes, which ore consisted of slender linear elements, are able to transmit external loads to the structure by in-plane forces, therefore spatial structures can be constructed with the merit of its own lightweight. But, as external load reaches to any critical level at which each member has not material nonlinearity, the single-layer latticed dome shows unstable phenomenon. In particular, pin-connected single-layer latticed domes have much complicate unstable phenomena that are combined with nodal buckling and member buckling. Furthermore, single-layer latticed domes are very sensible to the initial imperfection which occurred inevitably in construction. In this study, we are going to grasp the characteristics of instability for the latticed dome by finite element method considering geometrical nonlinearity.

• Journal of Korean Association for Spatial Structures
• /
• v.16 no.4
• /
• pp.45-52
• /
• 2016

The single layer latticed domes have attracted many designers and researchers's attention all of the world, because these structures as spatial structure are of great advantage in not only mechanical rationality but also function, fabrication, construction and economic aspect. But single layer latticed domes are apt to occur the unstable phenomena that are called "buckling" because of the lack of strength of members, instability of structural shape, etc. In the case of latticed dome, there are several types of buckling mode such as overall buckling, local buckling, and member buckling according to the shape of dome, section type of member, the size of member, junction's condition of member and so on. There are many methods to increase the buckling strength of the single layer latticed dome, that is, with the change of geometrical shape of dome, the reinforcement of buckled member, etc. Therefore, the purpose of this study is to verify the reinforcement effect of buckled member when designers reinforce the buckled member to increase the buckling strength of single layer latticed dome with 3-way grid.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.2
• /
• pp.5-12
• /
• 1998

Exploitation of the papermaking technology to reduce the strength loss that accompanies when using recycled papers as raw materials for papermaking is one of the most important issues imposed upon today's paper industry. Multi-layer sheet forming technology has been suggested as a way that provides some answers to this issue. In this study strength properties of single- and two-layer handsheets formed with recycled fiber and unbleached softwood kraft pulp have been examined to quantify the benefits when using two-layer sheet forming technology rather than a conventional single layer sheet forming precess. Single- and two-layer handsheets were made from 50% of OCC and 50% of Sw-UKP and their strength properties were evaluated. Also the strength properties made from Sw-UKP and OCC sheets were determined. A multihead, which can be attached on the top of hand- sheet former, was used to form two-layer sheets. Maximum strength properties could be obtained in the freeness range of 500∼300mL CSF for Sw-UKP Most of the strength properties was reduced by 30∼35% when 50% OCC was blended with UKP. Decrease of strength properties, however, could be reduced by employing a two-layer sheet forming method. Creator strengths could be obtained when UKP was positioned at the top layer of two layered sheets indicating greater UKP fines retention due to the filtration effect of the OCC layer formed prior to UKP layer contributed the strength improvement. Two-layer sheet showed lower Scott internal bond strength than single layer sheet. By incorporating some of UKP fibers into OCC layer this reduction could be reduced.

• Nano
• /
• v.13 no.12
• /
• pp.1850138.1-1850138.6
• /
• 2018

Two-dimensional (2D) or layered materials have a great potential for applications in energy storage, catalysis, optoelectronics and gas separation. Fabricating novel 2D or quasi-2D layered materials composed of relatively abundant and inexpensive atomic species is an important issue for practical usage in industry. Here, we suggest the layer-structured AlOOH (Boehmite) as a promising candidate for such applications. Boehmite is a well-known layer-structured material and a single-layer can be exfoliated from the bulk boehmite by breaking the interlayer hydrogen bonding. We study atomic and electronic band structures of both bulk and single-layer boehmite, and also obtain the single-layer exfoliation energy using first-principles calculations.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.5
• /
• pp.242-245
• /
• 2013

Sn-doped $In_2O_3$ (ITO) thin films were prepared by radio frequency magnetron sputtering without intentional substrate heating on bare glass and $TiO_2$-deposited glass substrates to investigate the effect of a $TiO_2$ buffer layer on the electrical and optical properties of ITO films. The thicknesses of $TiO_2$ and ITO films were kept constant at 5 and 100 nm, respectively. As-deposited ITO single layer films show an optical transmittance of 75.9%, while $ITO/TiO_2$ bi-layered films show a lower transmittance of 76.1%. However, as-deposited $ITO/TiO_2$ films show a lower resistivity ($9.87{\times}10^{-4}{\Omega}cm$) than that of ITO single layer films. In addition, the work function of the ITO film is affected by the $TiO_2$ buffer layer, with the $ITO/TiO_2$ films having a higher work-function (5.0 eV) than that of the ITO single layer films. The experimental results indicate that a 5-nm-thick $TiO_2$ buffer layer on the $ITO/TiO_2$ films results in better performance than conventional ITO single layer films.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.36.1-36.1
• /
• 2009

OLED(organic light emitting diode)는 차세대 평판 디스플레이로 전자종이, 입는 디스플레이 등 flexible한 디스플레이로도 주목받고 있다. 하지만, OLED의 가장 큰 단점 중의 하나가 수분과 산소에 매우 민감하다는 것으로 이것은 OLED의 lifetime과 연결된다. 따라서 이에 대한 mechanism의 확립이 필요하다. 따라서 본 연구에서는, flexible한 OLED에 적용되는 금속 코팅막의 적층구조 및 기판의 노출온도에 따른 금속 코팅막의 수분침투 특성에 대해 MOCON의 weight gain test (WGT)를 통해 barrier layer에 대해 평가하고 이에 대한 mechanism을 확립하는데 그 목적이 있다. 금속 코팅막은 OLED의 cathode와 anode 재료로 많이 사용되는 Al과 ITO를 sputter장비를 이용해 single layer와 multi-layer의 두 가지 구조로 PET기판에 증착하였다. 또한, 노출온도에 따른 특성을 알아보고자 bare PET / ITO coated PET(single layer $50{\mu}m$) / Al coated PET(single layer $200{\mu}m$)의 세 가지 시편을 제작하였다. 이 시편을 각각 $25^{\circ}C$, $37.8^{\circ}C$, $50^{\circ}C$의 온도에서 test를 진행하였고 이 과정을 100%RH, 70%RH, 40%RH조건의 수분조건에서 진행하여 각각의 수분조건에서 각각의 온도에 따른 금속 코팅막의 수분침투 특성에 대한 mechanism을 확립하였다. 적층구조에 따른 수분침투 특성 평가 결과 multi-layer가 single layer보다 더 우수한 수분침투의 barrier 특성을 나타냈었다. 그리고 각 온도에 따른 test결과 온도가 증가할수록 barrier의 특성이 나빠짐이 보였다.

• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.6
• /
• pp.422-433
• /
• 2015

In this paper, we demonstrate inter-layer prediction tools for scalable video coders. The proposed scalable coder is designed to support not only spatial, quality and temporal scalabilities, but also view scalability. In addition, we propose quad-tree inter-layer prediction tools to improve coding efficiency at enhancement layers. The proposed inter-layer prediction tools generate texture prediction signal with exploiting texture, syntaxes, and residual information from a reference layer. Furthermore, the tools can be used with inter and intra prediction blocks within a large coding unit. The proposed framework guarantees the rate distortion performance for a base layer because it does not have any compulsion such as constraint intra prediction. According to experiments, the framework supports the spatial scalable functionality with about 18.6%, 18.5% and 25.2% overhead bits against to the single layer coding. The proposed inter-layer prediction tool in multi-loop decoding design framework enables to achieve coding gains of 14.0%, 5.1%, and 12.1% in BD-Bitrate at the enhancement layer, compared to a single layer HEVC for all-intra, low-delay, and random access cases, respectively. For the single-loop decoding design, the proposed quad-tree inter-layer prediction can achieve 14.0%, 3.7%, and 9.8% bit saving.